（超經典）施工用電安全專項方案（含全套計算書）

1、 *名苑114#及管理用房 施工用電安全專項方案編制人: 職務(職稱):項目電氣技術負責人 審核人: 職務(職稱):質安科長 批準人: 職務(職稱):技術負責人 編制單位: *建設集團有限公司 編制時間: 年 月 日 本施工方案為安全施工組織設計的補充部分，關于工程概況、人員安排、進度計劃等此略。 本工程按照施工現場實際情況及用電安全考慮，施工用電采用三相五線制“tn-s”系統進行配電，現場設三只總配電箱，八只動力分配電箱及二只照明分配電箱，施工機具均單獨設置專用開關箱，其中兩臺對焊機及兩臺塔吊單獨從1#及3#總箱內引出，電纜線采用埋地設置（部分采用架空設置），各臨時用電安裝后須經公司安全負責

2、人和編制方案的人員參加驗收，驗收合格后方可使用。設計步驟如下:一、現場情況 施工現場臨時用電平面布置圖，見(附圖)。二、負荷計算根據臨時電源的位置及用電設備分布和現場環境條件等確定總配電箱、分配電箱和開關箱的位置。施工現場機械設備匯總表序號設備名稱臺數單機功率kw小計功率kw規格型號備注1塔吊16060qtz63開工進場2塔吊16060qtz63開工進場3物料提升機117.575sse100開工進場4砼攪拌機65.533tz350開工進場5插入式振動機401.560zn-50開工進場6平臺振動機201.122zbp-50開工進場7木工圓鋸21.53.0hb-50開工進場8鋼筋切斷機23.57.

3、0gq-40開工進場9鋼筋彎曲機22.24.4g26-40開工進場10對焊機290180un1-100開工進場電焊機210.521bxtf-3開工進場生活照明6.0總負荷計算pe =(60+60+75+33+60+22+3+7+4.4+180+21+6) =531.4kw則： pj = 0.6 531.4= 318.8kw qj = pjtan = 318.8 1.17 kvar373kvar sj = pj2 + qj2 = 318.82 +3732 =490.6kva sj 490.6 ij = = a 745.6a ue3 0.383 三、1#配電系統計算1#總配電箱機械設備匯總表序號設

4、備名稱臺數單機功率kw小計功率kw規格型號備注1塔吊16060qtz63開工進場2物料提升機67.545sse100開工進場3砼攪拌機35.516.5tz350開工進場4插入式振動機201.530zn-50開工進場5平臺振動機101.111zbp-50開工進場6木工圓鋸11.51.5hb-50開工進場7鋼筋切斷機13.53.5gq-40開工進場8鋼筋彎曲機12.22.2g26-40開工進場9對焊機19090un1-100開工進場10電焊機110.510.5bxtf-3開工進場生活照明6.0總負荷計算pe =(60+45+16.5+30+11+1.5+3.5+2.2+90+10.5+6)=276

5、.2kw則： pj = 0.6 276.2= 171kw qj = pjtan = 171 1.17 kvar200kvar sj = pj2 + qj2 = 1712 +2002 =263kva sj 263 ij = = a 399.8a ue3 0.383 1#總配電箱1-1分配電箱的計算負荷 pj1 = (3.5+2.2+1.5) =7.2kw(取cos=0.85,則tan = 0.62) qj1 = pj1tan = 7.2 0.62 kvar 4.5kvar sj1 = pj12 + qj12 = 7.22 +4.52 =8.5kva sj 8.5 ij1 = = a 12.9a

6、ue3 0.383 1#總配電箱1-2#分配電箱的計算負荷 pj2 = (7.5+7.5+5.5+7*1.5+4*1.1) = 35.4kw qj2 = pj2tan =35.4 0.62 kvar 22kvar sj2 = pj22 + qj22 = 35.42 +222 =41.7kva sj2 41.7 ij2 = = 63a ue3 0.383 1#總配電箱1-3#分配電箱的計算負荷 pj2 = (7.5+7.5+5.5+7*1.5+4*1.1) = 35.4kw qj2 = pj2tan =35.4 0.62 kvar 22kvar sj2 = pj22 + qj22 = 35.42

7、 +222 =41.7kva sj2 41.7 ij2 = = 63a ue3 0.3831#總配電箱1-4#分配電箱的計算負荷 pj2 = (7.5+7.5+5.5+6*1.5+3*1.1) = 32.8kw qj2 = pj2tan =32.8 0.62 kvar 20.36kvar sj2 = pj22 + qj22 = 32.82 +20.362 =38.6kva sj2 38.6 ij2 = = 58.6a ue3 0.3831#總配電箱對焊機的計算負荷 pj3 = 90kw qj3 = 900.62 kvar55.8kvar (取cos=0.85,tan=0.62) sj3 = 9

8、02 +55.82 105.9kva 105.9 ij3 = 160a ue3 1#總配電箱塔吊的計算負荷 pj3 = 60kw qj3 = 600.62 kvar37.2kvar (取cos=0.85,tan=0.62) sj3 = 602 +37.22 70.5kva 70.5 ij3 = 107a ue3 1#總配電箱照明分箱的計算負荷 pj(1) = 6.0kw qj(1) = 2.3 1.52 kvar 3.5kvar (取cos=0.5，tan=1.52) sj(1) = 6.02 +3.52 = 6.9kva 6.9 ij(1) = a 31.4a 0.22 2、導線及導線截面的

9、選擇（1#配電系統） 本施工現場場地不大，進戶線和總電源箱至各分配電箱的導線采用橡皮絕緣電纜(yc)按規范要求進行敷設。 選擇橡皮絕緣電纜的程序是，先按允許溫度初選截面，使jj小于電纜允許截流量，然后再效驗電壓損失，使其小于電壓損失規定值為滿足要求。 芯線最高溫度為65，環境溫度為25。進戶線由上可知，ij=399.8a查表可選yc 3 185m2 + 2 75m2 (i=388a)電纜1#總1-1段，l1= 59m =0.059km ij1 = 12.9a pj1 =7.2kw qj1 =4.5kvar 查表選 yc 3 25mm2 + 1 16mm2 (i=101a)電纜 電壓損失查表，電

10、纜的電阻r0=1.2/km，x0=0.295/km r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 =ua%+ ur%1.2 0.295 = 42.4 0.004 + 26.3 0.004 100.382 100.382 =0.83142.40.004+0.20426.30.004 = 0.140 + 0.021 = 0.16(%) (5%)滿足規定,1#總到第1-1分配電箱可選用yc 325m2+116m2的四蕊電纜。1#總-1-2段，l2 =63m =0.063km ij2 =63a pj2 =35.4kw qj2 =22kvar 查表選yc 325

11、m2+116m2 (i=101a)電纜 電壓損失查表，電纜的電阻ro=0.28/kw，電抗xo=0.258/kw r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 = ua%+ ur%0.28 0.258 = 107.7 0.085 + 66.80.085 100.382 100.382 = 0.193+ 1.014 = 1.20(%) (5%)滿足規定,1#總到第1-2分配電箱可選用yc 325m2 + 116m2的四蕊電纜。1#總-1-3段，l2 =63m =0.063km ij2 =63a pj2 =35.4kw qj2 =22kvar 查表選yc

12、325m2+116m2 (i=101a)電纜 電壓損失查表，電纜的電阻ro=0.28/kw，電抗xo=0.258/kw r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 = ua%+ ur%0.28 0.258 = 107.7 0.085 + 66.80.085 100.382 100.382 = 0.193+ 1.014 = 1.20(%) (5%)滿足規定,1#總到第1-3分配電箱可選用yc 325m2 + 116m2的四蕊電纜。1#總- 1-4段，l2 =120m =0.120km ij2 =58.6a pj2 =32.8kw qj2 =20.36k

13、var 查表選yc 325m2+216m2 (i=101a)電纜 電壓損失查表，電纜的電阻ro=0.28/kw，電抗xo=0.258/kw r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 = ua%+ ur%0.28 0.258 = 107.7 0.085 + 66.80.085 100.382 100.382 = 0.193+ 1.014 = 1.20(%) (5%)滿足規定,1#總到第1-4分配電箱可選用yc 325m2 + 116m2的四蕊電纜。1#總對焊機配電箱l2 =56m =0.056km ij2 = 160a pj2 = 90kw qj2

14、=55.8kvar 查表選yc 395m2+125m2 (i=191a)電纜 電壓損失查表，電纜的電阻ro=0.28/kw，電抗xo=0.258/kw r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 = ua%+ ur%0.28 0.258 = 107.7 0.085 + 66.80.085 100.382 100.382 = 0.193+ 1.014 = 1.20(%) (5%)滿足規定,總到對焊機開關箱可選用yc 395m2 + 125m2的四蕊電纜。1#總塔吊配電箱l2 =5m =0.005km ij2 = 107a pj2 = 60kw qj2

15、=37.2kvar 查表選yc 350m2+125m2 (i=158a)電纜 電壓損失查表，電纜的電阻ro=0.28/kw，電抗xo=0.258/kw r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 = ua%+ ur%0.28 0.258 = 107.7 0.085 + 66.80.085 100.382 100.382 = 0.193+ 1.014 = 1.20(%) 1.3ij1=1.312.9=16.8a 查表選用hr5-100a刀熔開關。(2) 漏電保護器的選擇 ih 1.3ij1=1.312.9=16.8a 查表選用dz15l-40/390型

16、漏電保護器，額定電壓380v，額定漏電動作電流75ma，額定漏電分?jǐn)鄷r(shí)間0.1s。(3) 隔離開關的選擇 控制切斷機開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。控制彎曲機開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a?？刂颇竟ら_(kāi)關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。第1-2分配電箱開關電器的選擇(1) 開關選擇： ih 1.3ij1=1.363=81.9a 查表選用rt-10/4刀熔開關。(2) 漏電保護器的選擇 ih 1.3ij1=1.363=81.9a 查表選用dz25l-40/390型漏電保護器，額定電壓380v，額

17、定動作電流75ma，額定漏電分?jǐn)鄷r(shí)間0.1s。(3) 隔離開關的選擇 控制井架開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。 控制攪拌機的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。 控制其他開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。第1-3分配電箱開關電器的選擇(1) 開關選擇： ih 1.3ij1=1.363=81.9a 查表選用rt-10/4刀熔開關。(2) 漏電保護器的選擇 ih 1.3ij1=1.363=81.9a 查表選用dz25l-40/390型漏電保護器，額定電壓380v，額定動作電流75ma，額定漏電分?jǐn)鄷r(shí)間0.

18、1s。(3) 隔離開關的選擇 控制井架開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。 控制攪拌機的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。 控制其他開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。第1-4分配電箱開關電器的選擇(1) 開關選擇： ih 1.3ij1=1.358.6=76a 查表選用rt-10/4刀熔開關。(2) 漏電保護器的選擇 ih 1.3ij1=1.358.6=76a 查表選用dz25l-40/390型漏電保護器，額定電壓380v，額定動作電流75ma，額定漏電分?jǐn)鄷r(shí)間0.1s。(3) 隔離開關的選擇 控制井架開

19、關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。 控制攪拌機的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。 控制其他開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。對焊機開關箱開關電器選擇 (1) 開關選擇 ih 1.3ij2=1.3192.6=250.3a 查表選用hr5-200a刀熔開關。(2) 漏電保護器的選擇 ih 1.3ij2=1.3192.6=250.3a 查表選用dz10l-63/490漏電保護器，過電流脫扣器額定電流100a，額定漏電動作電流100ma，額定不動作電流50ma，額定漏電分?jǐn)鄷r(shí)間0.1s。(3) 隔離開關的選擇

20、 控制對焊機開關箱的隔離開關選用hr5-200a刀熔開關，額定電流200a。塔吊開關箱開關電器選擇(1) 開關選擇 ih 1.3ij2=1.3107=139a 查表選用hr5-200a刀熔開關。(2) 漏電保護器的選擇 ih 1.3ij2=1.3107=139a 查表選用dz10l-63/490漏電保護器，過電流脫扣器額定電流100a，額定漏電動作電流100ma，額定不動作電流50ma，額定漏電分?jǐn)鄷r(shí)間0.1s。(3) 隔離開關的選擇 控制對焊機開關箱的隔離開關選用hr5-200a刀熔開關，額定電流照明分配電箱此略四、3#配電系統計算：3#總配電箱機械設備匯總表序號設備名稱臺數單機功率kw小計

21、功率kw規格型號備注1塔吊16060qtz63開工進場2物料提升機57.537.5sse100開工進場3砼攪拌機35.516.5tz350開工進場4插入式振動機201.530zn-50開工進場5平臺振動機101.111zbp-50開工進場6木工圓鋸11.51.5hb-50開工進場7鋼筋切斷機13.53.5gq-40開工進場8鋼筋彎曲機12.22.2g26-40開工進場9對焊機19090un1-100開工進場10電焊機110.510.5bxtf-3開工進場總負荷計算pe =(60+37.5+16.5+30+11+1.5+3.5+2.2+90+10.5+6)=268.7kw則： pj = 0.6

22、268.7= 162kw qj = pjtan = 162 1.17 kvar188kvar sj = pj2 + qj2 = 1622 +1882 =248.6kva sj 248.6 ij = = a 377.8a ue3 0.383 3#總配電箱3-1分配電箱的計算負荷 pj1 = (3.5+2.2+1.5) =7.2kw(取cos=0.85,則tan = 0.62) qj1 = pj1tan = 7.2 0.62 kvar 4.5kvar sj1 = pj12 + qj12 = 7.22 +4.52 =8.5kva sj 8.5 ij1 = = a 12.9a ue3 0.383 3#

23、總配電箱3-2#分配電箱的計算負荷 pj2 = (7.5+7.5+5.5+7*1.5+4*1.1) = 35.4kw qj2 = pj2tan =35.4 0.62 kvar 22kvar sj2 = pj22 + qj22 = 35.42 +222 =41.7kva sj2 41.7 ij2 = = 63a ue3 0.383 3#總配電箱3-3#分配電箱的計算負荷 pj2 = (7.5+5.5+7*1.5+4*1.1) = 27.9kw qj2 = pj2tan =27.9 0.62 kvar 17.3kvar sj2 = pj22 + qj22 = 27.92 +17.32 =32.3k

24、va sj2 32.3 ij2 = = 49a ue3 0.3833#總配電箱3-4#分配電箱的計算負荷 pj2 = (7.5+7.5+5.5+6*1.5+3*1.1) = 32.8kw qj2 = pj2tan =32.8 0.62 kvar 20.36kvar sj2 = pj22 + qj22 = 32.82 +20.362 =38.6kva sj2 38.6 ij2 = = 58.6a ue3 0.3833#總配電箱對焊機的計算負荷 pj3 = 90kw qj3 = 900.62 kvar55.8kvar (取cos=0.85,tan=0.62) sj3 = 902 +55.82 10

25、5.9kva 105.9 ij3 = 160a ue3 3#總配電箱塔吊的計算負荷 pj3 = 60kw qj3 = 600.62 kvar37.2kvar (取cos=0.85,tan=0.62) sj3 = 602 +37.22 70.5kva 70.5 ij3 = 107a ue3 導線及導線截面的選擇（1#配電系統） 本施工現場場地不大，進戶線和總電源箱至各分配電箱的導線采用橡皮絕緣電纜(yc)按規范要求進行敷設。 選擇橡皮絕緣電纜的程序是，先按允許溫度初選截面，使jj小于電纜允許截流量，然后再效驗電壓損失，使其小于電壓損失規定值為滿足要求。 芯線最高溫度為65，環境溫度為25。進戶線

26、由上可知，ij=377.8a查表可選yc 3 185m2 + 2 75m2 (i=388a)電纜3#總3-1段，l1=70m =0.070km ij1 = 12.9a pj1 =7.2kw qj1 =4.5kvar 查表選 yc 3 25mm2 + 1 16mm2 (i=101a)電纜 電壓損失查表，電纜的電阻r0=1.2/km，x0=0.295/km r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 =ua%+ ur%1.2 0.295 = 42.4 0.004 + 26.3 0.004 100.382 100.382 =0.83142.40.004+0

27、.20426.30.004 = 0.140 + 0.021 = 0.16(%) (5%)滿足規定,3#總到第3-1分配電箱可選用yc 325m2+116m2的四蕊電纜。3#總- 3-2段，l2 =40m =0.040km ij2 =63a pj2 =35.4kw qj2 =22kvar 查表選yc 325m2+116m2 (i=101a)電纜 電壓損失查表，電纜的電阻ro=0.28/kw，電抗xo=0.258/kw r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 = ua%+ ur%0.28 0.258 = 107.7 0.085 + 66.80.085

28、 100.382 100.382 = 0.193+ 1.014 = 1.20(%) (5%)滿足規定,3#總到第3-2分配電箱可選用yc 325m2 + 116m2的四蕊電纜。3#總- 3-3段，l2 =85m =0.085km ij2 =49a pj2 =27.9kw qj2 =17.3kvar 查表選yc 325m2+116m2 (i=101a)電纜 電壓損失查表，電纜的電阻ro=0.28/kw，電抗xo=0.258/kw r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 = ua%+ ur%0.28 0.258 = 107.7 0.085 + 66.

29、80.085 100.382 100.382 = 0.193+ 1.014 = 1.20(%) (5%)滿足規定,3#總到第3-3分配電箱可選用yc 325m2 + 116m2的四蕊電纜。3#總- 3-4段，l2 =120m =0.120km ij2 =58.6a pj2 =32.8kw qj2 =20.36kvar 查表選yc 325m2+216m2 (i=101a)電纜 電壓損失查表，電纜的電阻ro=0.28/kw，電抗xo=0.258/kw r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 = ua%+ ur%0.28 0.258 = 107.7 0

30、.085 + 66.80.085 100.382 100.382 = 0.193+ 1.014 = 1.20(%) (5%)滿足規定,3#總到第3-4分配電箱可選用yc 325m2 + 116m2的四蕊電纜。3#總對焊機配電箱l2 =10m =0.010km ij2 = 160a pj2 = 90kw qj2 =55.8kvar 查表選yc 395m2+125m2 (i=191a)電纜 電壓損失查表，電纜的電阻ro=0.28/kw，電抗xo=0.258/kw r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 = ua%+ ur%0.28 0.258 = 1

31、07.7 0.085 + 66.80.085 100.382 100.382 = 0.193+ 1.014 = 1.20(%) (5%)滿足規定,3#總到對焊機開關箱可選用yc 395m2 + 125m2的四蕊電纜。3#總塔吊配電箱l2 =20m =0.020km ij2 = 107a pj2 = 60kw qj2 =37.2kvar 查表選yc 350m2+125m2 (i=158a)電纜 電壓損失查表，電纜的電阻ro=0.28/kw，電抗xo=0.258/kw r0 n x 0 n u% = pala + qala 10ue2 1 10ue2 1 = ua%+ ur%0.28 0.258

32、= 107.7 0.085 + 66.80.085 100.382 100.382 = 0.193+ 1.014 = 1.20(%) 1.3ij1=1.312.9=16.8a 查表選用hr5-100a刀熔開關。(2) 漏電保護器的選擇 ih 1.3ij1=1.312.9=16.8a 查表選用dz15l-40/390型漏電保護器，額定電壓380v，額定漏電動作電流75ma，額定漏電分?jǐn)鄷r(shí)間0.1s。(3) 隔離開關的選擇 控制切斷機開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a?？刂茝澢鷻C(jī)開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a?？刂颇竟ら_(kāi)關箱的隔離

33、開關選用hg1-63/3熔斷式隔離開關，額定電流63a。第3-2分配電箱開關電器的選擇(1) 開關選擇： ih 1.3ij1=1.363=81.9a 查表選用rt-10/4刀熔開關。(2) 漏電保護器的選擇 ih 1.3ij1=1.363=81.9a 查表選用dz25l-40/390型漏電保護器，額定電壓380v，額定動作電流75ma，額定漏電分?jǐn)鄷r(shí)間0.1s。(3) 隔離開關的選擇 控制井架開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。 控制攪拌機的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。 控制其他開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，

34、額定電流63a。第3-3分配電箱開關電器的選擇(1) 開關選擇： ih 1.3ij1=1.349=63.7a 查表選用rt-10/4刀熔開關。(2) 漏電保護器的選擇 ih 1.3ij1=1.349=63.7a 查表選用dz25l-40/390型漏電保護器，額定電壓380v，額定動作電流75ma，額定漏電分?jǐn)鄷r(shí)間0.1s。(3) 隔離開關的選擇 控制井架開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。 控制攪拌機的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。 控制其他開關箱的隔離開關選用hg1-63/3熔斷式隔離開關，額定電流63a。第3-4分配電箱開關電器的選擇(1) 開關選擇： ih 1.3ij1=1.358.6=76a 查表選用rt-10/4刀熔開關。(2) 漏電保護器的選擇 ih 1.3ij1=1.358.6=76a 查表選用dz25l-40/390型漏電保