3機艙inst9個zch文件和輪轂安裝

1、機艙和輪轂安裝Installation of nacelle with hub檢查項目和規范：由現場填寫 To be filled in by the site已校準設備Calibrated equipment位置.nr設備描述（類型、名稱等）Description of equipment(Type ,name,etc)設備校準號Equipment calibration number123456789101112在上面的列表中詳列設備，隨后使用該設備時參考其位置。Specify equipment in list above, and subsequently refer to theNo

2、, when the equipment is used客戶/業主：Customer/owner:項目名稱：Project Name：項目：Project No:風機：Turbine No.:參照作業指導書：ZWI 1040333Work Instruction:ZWI 1040333ECN 222562 PTL 2015.11.10Check-item and specification:已校準設備位置： Cal. equipment完成日期（日/月/年） Date completed安裝 簽字installer signature監督簽字 Supervisor signature. no:

3、1安裝機艙前塔筒頂部法蘭Tower top flange cleaned before nacelle is installed.2根據作業指導書對螺栓涂抹潤滑脂根據作業指導書要求正確放置墊片和螺母，確保方向正確Stud bolts lubricated according to work instruction.Washers and nutsitioned correctly according to work instruction.3根據指導書要求安裝法蘭面螺栓根據指導書要求預緊法蘭面螺栓Flange bolts mounted according to work instructio

4、n.Flange bolts pretightened according to work instruction.4按終擰力矩要求擰緊螺栓，力矩Nm Stud bolts tightened to final toqueTorque:Nm風速風向儀安裝在合適位置Wind sensor support mounted in normal ition移除輪轂吊具螺母托在吊具的螺栓安裝盲塞Nut holder for hub lifting bracket removed Bling plugs mounted in bolt holes forlifting bracket安裝吊具的開口處安裝導

5、流罩分段。依據D1197831 “螺栓緊固-扭矩和緊固”擰緊螺栓Spinner sections in opening for lifting bracket mounted.Bolts tightened according to D1197831 “Bolt tightening - torque and ten”.備注：Remarks 全部完成，ZCH 完成。Completed, ZCH complete.監督員簽字： 日期： Supervisor signatureDate安裝簽字： 日期： Installation Signature：Date備注:檢查表必須在安裝或調試過程階段進行填寫,嚴禁提前填寫或后補,特此.Note: The checklist must be filled during