霍尼韋爾LON終端電阻95-7554

1、®U.S. Registered TrademarkCopyright © 1997 Honeywell Inc. All Rights Reserved BEFORE INSTALLATIONE-Bus Free Topology Transceiver (FTT/Linked PowerTransceiver (LPT networks require termination. Dependingon the network topology, one or more FTT/LPT TerminationModules may be required, see Fig

2、. 1. If an FTT Repeateror a LPT device is required in the network, their on-boardterminators can be used in place of the 209541BTermination Module. Refer to the E-Bus Wiring Guidelines, form 74-2865, for complete rules on network topology andtermination module locations. Refer to the Q7740A,B FTTRep

3、eater Installation Instructions, form 95-7555, forinformation on enabling the on-board network terminators.FTT networks are very flexible and convenient forinstallation and maintenance. However it is imperative tocarefully plan the network layout, and create and maintain accurate layout documentatio

4、n.INSTALLATIONThe FTT/LPT Termination Module can be attached to thenetwork at a controller node (the easiest place; In a wallmodule that is attached to standard utility junction box (themodule will not fit in a 60 mm junction box; At a wiringjunction (using wire nuts. See Fig. 6 when connecting twow

5、ires at a controller or wall module terminal. If thetermination module must be located at a surface mountedwall module, and does not fit inside the wall modulehousing, extend a pair of E-Bus wires from the wall moduleback to the nearest junction box or controller, and wire inthe termination module.

6、The module has three lead wires,but only two are attached to the E-Bus network .To installthe termination module, connect the brown and yellowwires to the E-Bus when the network requires single termination ; connect the brown and orange to the E-Buswhen the network requires double termination. In ei

7、thercase, always cover the unused wire with a wire nut toprevent potential grounding problems. As with other E-Busconnections, polarity is not important. Fig. 2 shows themodule attached to typical FTT/LPT network topologies fora single termination .Fig. 2. FTT/LPT termination module wiring for singl

8、etermination network topologies.Excel 10 FTT/LPT 209541BTERMINATION MODULEEXCEL 10 FTT/LPT 209541B TERMINATION MODULE Home and Building ControlHome and Building ControlHome and Building Control ProductsHoneywell Inc.Honeywell Limited-Honeywell LimiteeHoneywell AGHoneywell Plaza155 Gordon Baker RoadB

9、oblinger Strae 17P.O. Box 524North York, OntarioD-71101 SchomaichMinneapolis, MN 55408-0524M2H 3N7Phone (49-7031 637-01Fax (49-07031 637-493 95-7554 J.D. 3-97Printed in MexicoFig. 3 shows the physical connection of the module for asingle termination network. Fig. 4 shows the modulesattached to a typ

10、ical FTT/LPT network for a double termination . Fig. 5 shows the physical connection of themodules for a double termination network. Doubletermination is only applicable when a network is wired in adaisy-chain topology and the total wire length is greaterthan 1640 ft (500m. Refer to the E-Bus Wiring

11、 Guidelines, form 74-2865, for complete rules on network topology andtermination module locations.Fig. 3. Physical connection of module for a singletermination network.Fig. 4. FTT/LPT termination module wiring for doubletermination network topology.Fig. 5. Physical connection of modules for a double

12、termination network.STRIP 1/2 IN. (13 MM FROM WIRES TO BE ATTACHED AT ONE TERMINAL.1.2. TWIST WIRES TOGETHER WITH PLIERS (A MINIMUMOF THREE TURNS.3. CUT TWISTED END OF WIRES TO 3/16 IN. (5 MMBEFORE INSERTING INTO TERMINAL AND TIGHTENING SCREW. THEN PULL ON EACH WIRE IN ALL TERMINALSTO CHECK FOR GOOD MECHANICAL CONNECTION.M8945Fig. 6. Attaching two wires at controller or wall module terminals.NOTE:T