模具英語詞匯

1、2021/8/21模具英語詞匯模具英語詞匯Mould English Word2021/8/22（一）Mould Engineering模具工程詞匯2021/8/23一 ：入水：gate 進入位：gate location 水口形式：gate type 大水口：edge gate 細水口： pin-point gate 水口大小：gate size 轉水口：switching runner/gate 唧嘴口徑：sprue diameter 二：流道: runner 熱流道：hot runner,hot manifold 熱嘴冷流道: hot sprue/cold runner 唧嘴直流: di

2、rect sprue gate 圓形流道：round(full/half runner 流道電腦分析：mold flow analysis 流道平衡:runner balance 熱嘴：hot sprue 熱流道板：hot manifold發熱管：cartridge heater 探針: thermocouples 2021/8/24插頭：connector plug 插座： connector socket 密封/封料： seal 三：運水： water line 喉塞：line lpug 喉管：tube 塑膠管：plastic tube 快速接頭：jiffy quick connector

3、 plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 邊釘/導邊：leader pin/guide pin 邊司/導套：bushing/guide bushing 中托司：shoulder guide bushing 中托邊L：guide pin 頂針板：ejector retainner plate 托板：support plat 2021/8/25螺絲： screw 管釘：dowel pin 開模槽：ply bar scot 內模管位：core/cavity inter-lock 頂針：ejector p

4、in 司筒：ejector sleeve 司筒針：ejector pin 推板：stripper plate 縮呵：movable core,return core core puller 扣機（尼龍拉勾）：nylon latch lock斜頂：lifter 模胚（架）： mold base 上內模：cavity insert 下內模：core insert行位（滑塊）： slide 鑲件：insert 壓座/斜雞：wedge 耐磨板/油板：wedge wear plate 壓條：plate 2021/8/26撐頭: support pillar 唧嘴： sprue bushing 擋板：st

5、op plate 定位圈：locating ring 鎖扣：latch 扣雞：parting lock set 推桿：push bar 栓打螺絲：S.H.S.B頂板：eracuretun 活動臂：lever arm 分流錐：spure sperader 水口司:bush 垃圾釘：stop pin 隔片：buffle 彈弓柱：spring rod 彈弓:die spring 中托司：ejector guide bush 中托邊：ejector guide pi 2021/8/27鑲針：pin 銷子：dowel pin 波子彈弓：ball catch喉塞: pipe plug 鎖模塊：lock p

6、late 斜頂：angle from pin 斜頂桿：angle ejector rod 尼龍拉勾：parting locks活動臂：lever arm 復位鍵、提前回桿：early return bar 氣閥：valves 斜導邊：angle pin 五術語：terms 承壓平面平衡：parting surface support balance 模排氣：parting line venting 回針碰料位：return pin and cavity interference 2021/8/28?？偢叱銎C(jī)規格：mold base shut hight 頂針碰運水：water line i

7、nterferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不準用鑲件： Do not use (core/cavity) insert 用鈹銅做鑲件： use beryllium copper insert 初步（正式）模圖設計：preliinary (final) mold design 反呵：reverse core 彈弓壓縮量：spring compressed length 穩定性好：good

8、 stability,stable 強度不夠：insufficient rigidity 均勻冷卻：even cooling 扣模：sticking 熱膨脹：thero expansion 公差：tolorance 銅公(電極)：copper electrode2021/8/29六：common vocabulary for die engineering模具工程常用詞匯 die 模具 figure file, chart file圖檔 cutting die, blanking die沖裁模 progressive die, follow (-on)die 連續模 compound die復

9、合模 punched hole沖孔 panel board鑲塊 to cutedges=side cut=side scrap切邊 to bending折彎 to pull, to stretch拉伸 Line streching, line pulling線拉伸 engraving, to engrave刻印 upsiding down edges翻邊 to stake鉚合 designing, to design設計 design modification設計變化 die block模塊 folded block折彎塊 sliding block滑塊 2021/8/210location

10、pin定位銷 lifting pin頂料銷 die plate, front board模板 padding block墊塊 stepping bar墊條 upper die base上模座 lower die base下模座upper supporting blank上承板 upper padding plate blank上墊板 spring 彈簧 bolt螺栓plate電鍍 mold成型 material for engineering mold testing工程試模材料not included in physical inventory不列入盤點 sample樣品 ncoming m

11、aterial to be inspected進貨待驗 description品名2021/8/211（二）Mould Tool制模工具詞匯2021/8/212adjustable spanner 活動扳手 angle cutter 角銑刀 anvil 鐵鉆 arbour 心軸 backing 襯墊 belt sander 帶式打磨機 buffing 拋光 chamfering machine 倒角機 chamfering tool 去角刀具 chisel 扁鏨 chuck 夾具 compass 兩角規 concave cutter 凹面銑刀 convex cutter 凸形銑刀 cross

12、joint 十字接頭 cutting edge clearance 刃口余隙角 drill stand 鉆臺 edge file 刃用銼刀 2021/8/213file 銼刀 flange joint 凸緣接頭 grinder 砂輪機 hammer 鐵錘 hand brace 手搖鉆 hatching 剖面線 hexagon headed bolt六角頭螺栓 hexagon nut 六角螺帽 index head 分度頭 jack 千斤jig 治具 kit kit 工具箱工具箱 lapping lapping 研磨研磨 metal saw metal saw 金工鋸金工鋸 nose angle

13、 nose angle 刀角刀角 pinchers pinchers 鉗子鉗子 pliers pliers 鋏鉗頂鋏鉗頂 plug 柱塞頭 polisher 磨光器 protable driller 手提鉆孔機 2021/8/214punch 沖頭 sand paper 砂紙 scraper 刮刀 screw driver 螺絲起子 scribing 劃線 second out file 中紋銼 spanner 扳手 spline broach 方栓槽拉刀 square 直角尺 square sleeker 方形鏝刀 square trowel 直角度 stripping 剝離工具 T-slo

14、t T形槽 tool for lathe 車刀 tool point angle 刀刃角 tool post 刀架 tosecan 劃線盤 trimming 去毛邊 waffle die flattening 壓紋效平 2021/8/215wiper 脫模鉗 wrench 螺旋扳手 analog-mode device類模器 die lifter舉模器 argon welding氬焊pedal踩踏板 stopper阻擋器 flow board流水板 hydraulic handjack油壓板車 forklift叉車 pallet棧板 glove(s)手套 glove(s) with expos

15、ed fingers割手套 thumb大拇指 forefinger食指 midfinger中指 ring finger無名指little finger小指 band-aid創可貼 iudustrial alcohol工業酒精 2021/8/216alcohol container沾濕臺 head of screwdriver起子頭 sweeper掃把 mop拖把 vaccum cleaner吸塵器 rag 抹布 garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain鏈條 jack升降機 production line流水線 chain鏈條

16、槽 magnetizer加磁器 lamp holder燈架 to mop the floor拖地to clean the floor掃地 to clean a table擦桌子 2021/8/217air pipe 氣管 packaging tool打包機 packaging打包automatic screwdriver電動啟子 thickness gauge厚薄規 gauge(or jig)治具 power wire電源線 buzzle蜂鳴器 defective product label不良標簽 identifying sheet list標示單 screwdriver holder起子插

17、座 2021/8/218（三）Defect in Molding成型缺陷詞匯2021/8/219aberration 色差 atomization 霚化 bank mark 滯料紋bite bite 咬入咬入 blacking hole blacking hole 涂料孔涂料孔( (鑄疵鑄疵) ) blacking scab blacking scab 涂料疤涂料疤 blister blister 起泡起泡 blooming blooming 起霜起霜 blow hole blow hole 破孔破孔 blushing blushing 泛白泛白 body wrinkle body wrink

18、le 側壁皺紋側壁皺紋 breaking-in breaking-in 冒口帶肉冒口帶肉 bubble bubble 膜泡膜泡 burn mark burn mark 糊斑糊斑 burr burr 毛邊毛邊 camber camber 翹曲翹曲 center buckle center buckle 表面中部波皺表面中部波皺 check check 細裂痕細裂痕 checking checking 龜裂龜裂 2021/8/220chipping 修整表面缺陷 clamp-off 鑄件凹痕 collapse 塌陷 color mottle 色斑 corrosion 腐蝕 crack 裂痕 cra

19、zing 碎裂 deformation 變形 edge 切邊碎片 edge crack 裂邊 fading 退色 filler speak 填充料斑 fissure 裂紋 galling 毛邊 glazing 光滑 gloss 光澤 grease pits 污斑 grinding defect 磨痕 2021/8/221haircrack 發裂 haze 霧度 incrustation 水銹 indentation 壓痕flange wrinkle 凸緣起皺 flaw 刮傷cell 氣泡overflow 溢流 peeling 剝離 pit 坑 pitting corrosion 點狀腐蝕 pl

20、ate mark 模板印痕 pock 麻點 pock mark 痘斑 resin streak 樹脂流紋 resin wear 樹脂脫落 riding 凹陷 sagging 松垂 saponification 皂化 2021/8/222scar 疤痕 scrap 廢料 scrap jam 廢料阻塞 scratch 刮傷/劃痕 scuffing 深沖表面劃傷seam 裂痕short shot 充填不足 shrinkage pool 凹孔 sink mark 凹痕 skin inclusion 表皮折迭 straightening 矯直 streak 條狀痕 surface check 表面裂痕

21、surface roughening 橘皮狀表皮皺折 surging 波動 sweat out 冒汗 torsion 扭曲 warpage 翹曲 waviness 波痕 2021/8/223webbing 熔塌 weld mark 焊痕 whitening 白化 wrinkle 皺紋 shock line ?？跀D痕critical defect極嚴重缺陷 major defect主要缺陷 minor defect次要缺陷not up to standard不合規格 not up todimension/size is a little bigger尺寸偏大(小) cosmetic defect

22、外觀不良 slipped screwhead/slippery screw head螺絲滑頭 slipped screwhead/shippery screw thread滑手 speckle斑點 mildewed=moldy=mouldy發霉 rust生銹 deformation變形 burr(金屬) flash(塑件)毛邊 poor staking鉚合不良2021/8/224excesssive gap間隙過大 grease/oil stains油污 inclusion雜質 painting peel off臟污 shrinking/shrinkage縮水 mixed color雜色 sc

23、ratch劃傷 poor processing 制程不良 poor incoming part事件不良 fold of pakaging belt打包帶折皺 painting make-up補漆 discoloration羿色 water spots水漬 polishing/surface processing表面處理 exposed metal/bare metal金屬裸露 ack of painting烤漆不到位qualified products, up-to-grade products良品 defective products, not up-to-grade products不良品

24、 waste廢料 2021/8/225missing part漏件 wrong part錯件 excessive defects過多的缺陷 2021/8/226(四）Heat Treatment熱處理詞匯2021/8/227age hardening 時效硬化 ageing 老化處理 air hardening 氣體硬化 air patenting 空氣韌化 annealing 退火 anode effect 陽極效應 anodizing 陽極氧化處理 atomloy treatment 阿扥木洛伊表面 austempering 奧氏體等溫淬火 austenite 奧斯田體/奧氏體 baini

25、te 貝氏體 banded structure 條紋狀組織 barrel plating 滾鍍 barrel tumbling 滾筒打光 blackening 染黑法 blue shortness 青熟脆性 bonderizing 磷酸鹽皮膜處理 box annealing 箱型退火 box carburizing 封箱滲碳 bright electroplating 輝面電鍍 2021/8/228bright heat treatment 光輝熱處理 bypass heat treatment 旁路熱處理 carbide 炭化物 carburized case depth 浸碳硬化深層 ca

26、rburizing 滲碳 cementite 炭化鐵 chemical plating 化學電鍍 chemical vapor deposition 化學蒸鍍 coarsening 結晶粒粗大化 coating 涂布被覆 cold shortness 低溫脆性 comemtite 滲碳體depth of hardening 硬化深層 diffusion 擴散 diffusion annealing 擴散退火 electrolytic hardening 電解淬火 embossing 壓花 etching 表面蝕刻 ferrite 肥粒鐵 first stage annealing 第一段退火

27、2021/8/229flame hardening 火焰硬化 flame treatment 火焰處理 full annealing 完全退火 gaseous cyaniding 氣體氧化法 globular cementite 球狀炭化鐵controlled atmosphere 大氣熱處理 corner effect 銳角效應 creeping discharge 蠕緩放電 decarburization 脫碳處理 decarburizing 脫碳退火hardenability curve 硬化性曲線 hardening 硬化 heat treatment 熱處理 hot bath que

28、nching 熱浴淬火 hot dipping 熱浸鍍 induction hardening 高周波硬化 ion carbonitriding 離子滲碳氮化 ion carburizing 離子滲碳處理 ion plating 離子電鍍 isothermal annealing 等溫退火 liquid honing 液體噴砂法 2021/8/230low temperature annealing 低溫退火 malleablizing 可鍛化退火 martempering 麻回火處理 martensite 馬氏體/硬化鐵炭 metallikon 金屬?lài)婂兎╣rain size 結晶粒度 gr

29、anolite treatment 磷酸溶液熱處理 graphitizing 石墨退火 hardenability 硬化性nitriding 氮化處理 nitrocarburizing 軟氮化 normalizing 正常化 oil quenching 油淬化 overageing 過老化 overheating 過熱 pearlite 針尖組織 phosphating 磷酸鹽皮膜處理 physical vapor deposition 物理蒸鍍quench hardening 淬火 quenching crack 淬火裂痕 2021/8/231quenching distortion 淬火變

30、形 quenching stress 淬火應力 reconditioning 再調質 recrystallization 再結晶 red shortness 紅熱脆性 residual stress 殘留應力 retained austenite 殘留奧 rust prevention 防蝕 salt bath quenching 鹽浴淬火 sand blast 噴砂處理 seasoning 時效處理 second stage annealing 第二段退火plasma nitriding 離子氮化 pre-annealing 預備退火 precipitation 析出 precipitati

31、on hardening 析出硬化 press quenching 加壓硬化 process annealing 制程退火 quench ageing 淬火老化secular distortion 經年變形 2021/8/232segregation 偏析 selective hardening 部分淬火 shot blast 噴丸處理 shot peening 珠擊法 single stage nitriding 等溫滲氮 sintering 燒結處理 soaking 均熱處理 softening 軟化退火 solution treatment 固溶化熱處理 spheroidizing 球狀

32、化退火 stabilizing treatment 安定化處理 straightening annealing 矯直退火 strain ageing 應變老化 stress relieving annealing 應力消除退火 subzero treatment 生冷處理 supercooling 過冷 surface hardening 表面硬化處理temper brittleness 回火脆性 temper colour 回火顏色 tempering 回火 2021/8/233tempering crack 回火裂痕 texture 咬花 thermal refining 調質處理 the

33、rmoechanical treatment 加工熱處理 time quenching 時間淬火 transformation 變態 tufftride process 軟氮化處理 under annealing 不完全退火 vacuum carbonitriding 真空滲碳氮化 vacuum carburizing 真空滲碳處理 vacuum hardening 真空淬火 vacuum heat treatment 真空熱處理 vacuum nitriding 真空氮化 water quenching 水淬火 wetout 浸潤處理 2021/8/234(五）Machine機床詞匯2021

34、/8/235punching machine 沖床 robot機械手 hydraulic machine油壓機 lathe車床 planer |plein |刨床miller銑床 grinder磨床 driller鉆床 linear cutting線切割 electrical sparkle電火花 welder電焊機 staker=reviting machine鉚合機CNC/computerized numerical control 電腦鑼/加工中心2021/8/236(六）Plastic Material塑膠原料名稱詞匯2021/8/237英文簡稱 英文全稱 中文全稱 ABA Acryl

35、onitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物 ABS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物 AES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物 AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物 ARP Aromatic polyester 聚芳香酯 AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯樹脂 ASA Acrylonitrile-styrene-acrylat

36、e 丙烯腈/苯乙烯/丙烯酸酯共聚物 CA Cellulose acetate 醋酸纖維塑料 CAB Cellulose acetate butyrate 醋酸-丁酸纖維素塑料 CAP Cellulose acetate propionate 醋酸-丙酸纖維素 CE Cellulose plastics, general 通用纖維素塑料 CF Cresol-formaldehyde 甲酚-甲醛樹脂 CMC Carboxymethyl cellulose 羧甲基纖維素 CN Cellulose nitrate 硝酸纖維素 CP Cellulose propionate 丙酸纖維素 CPE Chlo

37、rinated polyethylene 氯化聚乙烯 CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯 CS Casein 酪蛋白 CTA Cellulose triacetate 三醋酸纖維素 2021/8/238EC Ethyl cellulose 乙烷纖維素 EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物 EP Epoxy, epoxide 環氧樹脂 EPD Ethylene-propylene-diene 乙烯-丙烯-二烯三元共聚物 EPM Ethylene-propylene polymer 乙烯-丙烯共聚物

38、 EPS Expanded polystyrene 發泡聚苯乙烯 ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物 EVA Ethylene/vinyl acetate 乙烯-醋酸乙烯共聚物 EVAL Ethylene-vinyl alcohol 乙烯-乙烯醇共聚物 FEP Perfluoro(ethylene-propylene) 全氟（乙烯-丙烯）塑料 FF Furan formaldehyde 呋喃甲醛 HDPE High-density polyethylene plastics 高密度聚乙烯塑料 HIPS High impact polysty

39、rene 高沖聚苯乙烯 IPS Impact-resistant polystyrene 耐沖擊聚苯乙烯 LCP Liquid crystal polymer 液晶聚合物 LDPE Low-density polyethylene plastics 低密度聚乙烯塑料 LLDPE Linear low-density polyethylene 線性低密聚乙烯 LMDPE Linear medium-density polyethylene 線性中密聚乙烯 MBS Methacrylate-butadiene-styrene 甲基丙烯酸-丁二烯-苯乙烯共聚物 2021/8/239MC Methyl

40、 cellulose MDPE Medium-density polyethylene 中密聚乙烯 MF Melamine-formaldehyde resin 密胺-甲醛樹脂 MPF Melamine/phenol-formaldehyde 密胺/酚醛樹脂 PA Polyamide (nylon) 聚酰胺（尼龍） PAA Poly(acrylic acid) 聚丙烯酸 PADC Poly(allyl diglycol carbonate) 碳酸-二乙二醇酯 烯丙醇酯樹脂 PAE Polyarylether 聚芳醚 PAEK Polyaryletherketone 聚芳醚酮 PAI Polya

41、mide-imide 聚酰胺-酰亞胺 PAK Polyester alkyd 聚酯樹脂 PAN Polyacrylonitrile 聚丙烯腈 PARA Polyaryl amide 聚芳酰胺 PASU Polyarylsulfone 聚芳砜 PAT Polyarylate 聚芳酯 PAUR Poly(ester urethane) 聚酯型聚氨酯 PB Polybutene-1 聚丁烯-1 PBA Poly(butyl acrylate) 聚丙烯酸丁酯 PBAN Polybutadiene-acrylonitrile 聚丁二烯-丙烯腈 2021/8/240PBS Polybutadiene-st

42、yrene 聚丁二烯-苯乙烯 PBT Poly(butylene terephthalate) 聚對苯二酸丁二酯 PC Polycarbonate 聚碳酸酯 PCTFE Polychlorotrifluoroethylene 聚氯三氟乙烯 PDAP Poly(diallyl phthalate) 聚對苯二甲酸二烯丙酯 PE Polyethylene 聚乙烯 PEBA Polyether block amide 聚醚嵌段酰胺 PEBA Thermoplastic elastomer polyether 聚酯熱塑彈性體 PEEK Polyetheretherketone 聚醚醚酮 PEI Poly

43、(etherimide) 聚醚酰亞胺 PEK Polyether ketone 聚醚酮 PEO Poly(ethylene oxide) 聚環氧乙烷 PES Poly(ether sulfone) 聚醚砜 PET Poly(ethylene terephthalate) 聚對苯二甲酸乙二酯 PETG Poly(ethylene terephthalate) glycol 二醇類改性PET PEUR Poly(ether urethane) 聚醚型聚氨酯 PF Phenol-formaldehyde resin 酚醛樹脂 PFA Perfluoro(alkoxy alkane) 全氟烷氧基樹脂

44、PFF Phenol-furfural resin 酚呋喃樹脂 PI Polyimide 聚酰亞胺 2021/8/241PVAL Poly(vinyl alcohol) 聚乙烯醇 PVB Poly(vinyl butyral) 聚乙烯醇縮丁醛 PVC Poly(vinyl chloride) 聚氯乙烯 PVCA Poly(vinyl chloride-acetate) 聚氯乙烯醋酸乙烯酯 PVDC Poly(vinylidene chloride) 聚（偏二氯乙烯） PVDF Poly(vinylidene fluoride) 聚（偏二氟乙烯） PVF Poly(vinyl fluoride)

45、 聚氟乙烯 PVFM Poly(vinyl formal) 聚乙烯醇縮甲醛 PVK Polyvinylcarbazole 聚乙烯咔唑 PVP Polyvinylpyrrolidone 聚乙烯吡咯烷酮 S/MA Styrene-maleic anhydride plastic 苯乙烯-馬來酐塑料SAN Styrene-acrylonitrile plastic 苯乙烯-丙烯腈塑料 SB Styrene-butadiene plastic 苯乙烯-丁二烯塑料 Si Silicone plastics 有機硅塑料 SMS Styrene/alpha-methylstyrene plastic 苯乙烯

46、-甲基苯乙烯塑料 SP Saturated polyester plastic 飽和聚酯塑料 SRP Styrene-rubber plastics 聚苯乙烯橡膠改性塑料 TEEE Thermoplastic Elastomer,Ether-Ester 醚酯型熱塑彈性體 TEO Thermoplastic Elastomer, Olefinic 聚烯烴熱塑彈性體 2021/8/242TES Thermoplastic Elastomer, Styrenic 苯乙烯熱塑性彈性體 TPEL Thermoplastic elastomer 熱塑(性)彈性體 TPES Thermoplastic po

47、lyester 熱塑性聚酯 TPUR Thermoplastic polyurethane 熱塑性聚氨酯 TSUR Thermoset polyurethane 熱固聚氨酯 UF Urea-formaldehyde resin 脲甲醛樹脂 UHMWPE Ultra-high molecular weight PE 超高分子量聚乙烯 UP Unsaturated polyester 不飽和聚酯 VCE Vinyl chloride-ethylene resin 氯乙烯/乙烯樹脂 VCEV Vinyl chloride-ethylene-vinyl 氯乙烯/乙烯/醋酸乙烯共聚物 VCMA Viny

48、l chloride-methyl acrylate 氯乙烯/丙烯酸甲酯共聚物 VCMMA Vinyl chloride-methylmethacrylate 氯乙烯/甲基丙烯酸甲酯共聚物 VCOA Vinyl chloride-octyl acrylate resin 氯乙烯/丙烯酸辛酯樹脂 VCVAC Vinyl chloride-vinyl acetate resin 氯乙烯/醋酸乙烯樹脂 VCVDC Vinyl chloride-vinylidene chloride 氯乙烯/偏氯乙烯共聚物 2021/8/243（七）Steel for Mold模具鋼材詞匯2021/8/244allo

49、y tool steel 合金工具鋼 aluminium alloy 鋁合金鋼 bearing alloy 軸承合金 blister steel 浸碳鋼 bonderized steel sheet 邦德防蝕鋼板 carbon tool steel 碳素工具鋼 clad sheet 被覆板 clod work die steel 冷鍛模用鋼 emery 金鋼砂 ferrostatic pressure 鋼鐵水靜壓力 forging die steel 鍛造模用鋼 galvanized steel sheet 鍍鋅鐵板 hard alloy steel 超硬合金鋼 high speed tool

50、 steel 高速度工具鋼 hot work die steel 熱鍛模用鋼 low alloy tool steel 特殊工具鋼 low manganese casting steel 低錳鑄鋼 marging steel 馬式體高強度熱處理鋼 martrix alloy 馬特里斯合金 meehanite cast iron 米漢納鑄鋼 2021/8/245meehanite metal 米漢納鐵 merchant iron 市售鋼材 molybdenum high speed steel 鉬系高速鋼 molybdenum steel 鉬鋼 nickel chromium steel 鎳鉻鋼 prehardened steel 頂硬鋼 silicon steel sheet 硅鋼板 stainless steel 不銹鋼 tin plated steel sheet 鍍錫鐵板 tough pitch copper 韌銅 troostite 吐粒散鐵 tungsten steel 鎢鋼 vinyl tapped steel sheet 塑料覆面鋼板2021/8/246（八）Punch Press沖壓詞匯2021/8/247stamping, press沖壓 punch press, die