實驗7QoS流量分類、標記及排隊

1、實驗7 QoS流量分類、標記及排隊1. 實驗?zāi)康恼莆誕os流量分類、標記方法;掌握Qos流量排隊方法。2. 實驗設備2811路由器、PC機3. 實驗過程首先，配置各接口的IP地址。配置各路由器路由:ip route 0. 0. 0. 0 0. 0. 0. 0 f0/03. 1 PQ排隊策略（1）在R1或R2路由器中設置enconf taccess-list 100 permit icmp any any priority-list 1 protocol ip high tcptelnet/Telnet流量定義為High優先級priority-list 1 protocol ip low lis

2、t100/ICMP流量定義為low優先級int f0/0priority-group 1/在接口應用優先級隊列(2) 查看結果show int f0/0sh queueing priority(3) 調試結果debug priority/扌丁開debugPCI ping PC2 以及 PCI telnet R2,查看 debug 的輸出。*Mar 1 00:25:17.235: PQ: FastEthernetO/0: ip (s=,d二 192. 16& 1. 1) - low*Mar 1 00:25:17.235: PQ: FastEthernetO/0 output

3、 (Pk size/Q 114/3)*Mar 1 00:25:17.419: PQ: FastEthernetO/0: ip (s=, (1=192. 168. 1. 1) - low*Mar1 00:25:17.419: PQ: FastEthernetO/0 output (Pk size/Q 114/3)*Mar1 00:25:17.691: PQ: FastEthernetO/O: ip (s=192. 168. 0.1,d二 192. 168. 1. 1) - low*Mar1 00:25:17. 695:PQ: FastEthernetO/0 output (

4、Pk size/Q 114/3)*Mar 1 00:25:17.799:PQ: FastEthernetO/O:ip(s二 192. 16& 0. 1,d=192. 168. 1. 1) - low*Mar00:26:56. 971:PQ: FastEthernetO/O:ip23)high*Mar00:26:57. 151:PQ: FastEthernetO/O:ip23)high*Mar00:26:57. 159:PQ: FastEthernetO/O:ip23)high*Mar00:26:57. 163:PQ: FastEthernetO/O:ip23)high*Mar00:26:57.

5、 167:PQ: FastEthernetO/O:ip23)high體會其它命令的作用priority-list 1 interface f0/0 highpriority-list 1 defauIt lowpriority-list 1 queueTimit 22 33 44 553.2CQ排隊策略在fO/O端口刪除，剛才配置的PQ策略，并進行下面的配置。（1）在R1或R2路由器中設置access-list 100 permit icmp any anyqueue-list 1 protocol ip 2 tcptelnet/Telnet流量定義為第2個隊列queue-list 1 pro

6、tocol ip 3 list100/ICMP流量定義為第3個隊列interface FastEthernetO/0/在接口應用優先級隊列custom - queueTist 1show int f0/0Queueing strategy： custom-list 1Output queues: (queue #： size/max/drops)0: 0/20/0 1: 0/20/0 2: 0/20/0 3: 0/20/0 4: 0/20/05: 0/20/0 6: 0/20/0 7: 0/20/0 8: 0/20/0 9: 0/20/010: 0/20/0 11: 0/20/0 12: 0/

7、20/0 13: 0/20/0 14: 0/20/015: 0/20/0 16: 0/20/0查看結果sh queueing customRouterSsh queueing customCurrent custom queue configuration： List Queue Args1 2 protocol ip tcp port telnet1 3 protocol ip list 100調試結果debug custom-queue*Mar 1 00:34:32.415:CQ: FastEthernetO/0output(Pksize/Q: 114/3)Q #was 1 now 3*M

8、ar 1 00:34:32.615:CQ: FastEthernetO/0output(Pksize/Q: 114/3)Q #was 3 now 3*Mar 1 00:35:40.207:CQ: FastEthernetO/0output(Pksize/Q: 60/2)Q # was1 now 2*Mar 1 00:35:40.283:CQ: FastEthernetO/0output(Pksize/Q: 60/2)Q # was2 now 2*Mar 1 00:35:40. 287:CQ: FastEthernetO/0output(Pksize/Q： 63/2)Q # was2 now 2

9、體會其它命令的作用/來自于f0/0端口的/沒有定義的流量默認queue-list 1 interface f0/0 1 所有流量定義為笫1個隊列queue-list 1 defauIt 15為第1個隊列，但可以設置queue-list 1 queue 2 byte-count 3000隊列2的門限值設置為3000字節，默認為1500字節包,queue-list 1 queue 2 limit 40默認為20個包隊列2的隊列大小為40個efWWW3.3 CBLLQ排隊策略在R1或者R2路由器上配置下列命令(1)配置ACL配置R1 (config)#accesslist 100 permit ip

10、 any any precedence語音流量R1 (config)#accesslist 100 permit ip any any dscp語音流量R1 (config)#access-list 101 permit tcp any any eq/Web流量R1 (config)#accesslist 102 permiticmp anyany/ICMP流量配置Class-mapR1(config)#class-map VOIPR1 (config-cmap)Smatch access-group 100R1(config-cmap)#class-map HTTP/語音/Web 流/ICM

11、P 流/其余使R1 (config-cmap)Smatch access-group 101R1(config-cmap)#class-map ICMPR1(config-cmap)Smatch access-group 102R1 (config-cmap)#exit(3)配置 policy-mapR1 (config)#policy-map QosR1(config-pmap)#class VOIPR1 (config-pmap-c)Spriority 100流量，帶寬限制為100KR1(config-pmap-c)#class HTTPR1(config-pmap-c)#bandwidth percent 50量，帶寬限制為剩余流量的50%R1(config-pmap-c)#class ICMPR1(config-pmap-c)Sbandwidth percent 1量，帶寬限制為剩余流量的1%R1(config-pmap-c)#class class-default用WFQ隊列R1 (conf ig-pmap-c)#fair-queu