【BS英國標準word原稿】BS EN 10213-4-1996 Technical delivery conditions for steel castings for pressure purposes. Austenit.doc

，如果你需要更多標準可以到/kmust1進行免費查閱。 如果你購買的文檔存在缺頁、字跡模糊、亂碼等情況，請大家通過論壇消息與我聯系。licensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsibritish standard bs en10213-4:1996technical delivery conditions for steel castings for pressure purposes part 4: austenitic and austenitic-ferritic steel gradesthe european standard en 10213-4:1995 has the status of abritish standardics 11.140.30 ，如果你需要更多標準可以到/kmust1進行免費查閱。 如果你購買的文檔存在缺頁、字跡模糊、亂碼等情況，請大家通過論壇消息與我聯系。bs en 10213-4:1996committees responsible for thisbritish standardthe preparation of this british standard was entrusted to technical committee ise/6, steel castings, upon which the following bodies were represented:beama ltd.british pump manufacturers associationbritish valve and actuator manufacturers associationcastings technology internationalengineering equipment and materials users associationhopkinsons limitedinstitute of british foundrymen institution of mechanical engineers lloyds register of shipping ministry of defencerailway industry associationlicensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsithis british standard, having been prepared under the direction of the engineering sector board, was published under the authority of the standards board and comes into effect on15 may 1996 bsi 12-1998the following bsi references relate to the work on this standard:committee reference ise/6draft for comment 93/301842 dcisbn 0 580 25543 3amd. no.datecommentsamendments issued since publicationlicensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsibs en 10213-4:1996contentspage committees responsibleinside front cover national forewordiiforeword2text of en 10213-43 bsi 12-1998ibs en 10213-4:1996licensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsinational forewordthis british standard has been prepared under the direction of technical committee ise/6, steel castings, and is the english language version of en 10213-4 technical delivery conditions for steel castings for pressurepurposes part 4: austenitic and austenitic-ferritic steel grades published by theeuropean committee for standardization (cen).the following parts of bs en 10213 supersede bs 1504:1976 which is now withdrawn:bs en 10213-1technical delivery conditions for steel castings for pressure purposespart 1:1996 generalbs en 10213-2technical delivery conditions for steel castings for pressure purposespart 2:1996 steel grades for use at room temperature and elevated temperaturesbs en 10213-3technical delivery conditions for steel castings for pressure purposespart 3:1996 steels for use at low temperaturesbs en 10213-4technical delivery conditions for steel castings for pressure purposespart 4:1996 austenitic and austenitic-ferritic steel gradesa british standard does not purport to include all the necessary provisions of a contract. users of british standards are responsible for their correct application.compliance with a british standard does not of itself confer immunity from legal obligations.summary of pagesthis document comprises a front cover, an inside front cover, pages i and ii, the en title page, pages 2 to 6 and a back cover.this standard has been updated (see copyright date) and may have had amendments incorporated. this will be indicated in the amendment table on the inside front cover. bsi 12-1998iieuropean standard norme europenneeuropische normen 10213-4december 1995ics 77.140.10descriptors: cast steels, structural steels, boilers, pressure equipment, delivery, designation, grades: quality, chemical composition, mechanical properties, austenitic steels, ferritic steelsenglish versiontechnical delivery conditions for steel castings for pressure purposes part 4: austenitic and austenitic-ferritic steel gradesconditions techniques de livraison des pices moules en acier pour service sous pression partie 4: nuances daciers austnitiques et austno-ferritiquestechnische lieferbedingungen fr stahlgu fr druckbehlter teil 4: austenitische und austenitisch-ferritische stahlsortenlicensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsithis european standard was approved by cen on 1995-10-20. cen members are bound to comply with the cen/cenelec internal regulations which stipulate the conditions for giving this european standard the status of a national standard without any alteration.up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the central secretariat or to any cen member.this european standard exists in three official versions (english, french, german). a version in any other language made by translation under the responsibility of a cen member into its own language and notified to the central secretariat has the same status as the official versions.cen members are the national standards bodies of austria, belgium, denmark, finland, france, germany, greece, iceland, ireland, italy, luxembourg, netherlands, norway, portugal, spain, sweden, switzerland and united kingdom.ceneuropean committee for standardization comit europen de normalisation europisches komitee fr normungcentral secretariat: rue de stassart 36, b-1050 brussels 1995 all rights of reproduction and communication in any form and by any means reserved in all countries to cen and its membersref. no. en 10213-4:1995 een 10213-4:1995 bsi 12-19982licensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsiforewordthis european standard was prepared by technical committee eciss/tc 31, steel castings, the secretariat of which is held by afnor.the text of the european standard en 10213technical delivery conditions for steel castings for pressure purposes consists of 4 parts: part 1: general; part 2: steel grades for use at room temperature and elevated temperatures; part 3: steel grades for use at low temperatures; part 4: austenitic and austenitic-ferritic steel grades.this european standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by june 1996, and conflicting national standards shall be withdrawn at the latest by june 1996.according to the internal regulations of cen/cenelec, the following countries are bound to implement this european standard: austria, belgium, denmark, finland, france, germany, greece, iceland, ireland, italy, luxembourg, netherlands, norway, portugal, spain, sweden, switzerland and the united kingdom.contentspageforeword21scope32normative references33requirements3annex a (informative)creep properties6table 1 chemical composition(cast analysis) 4table 2 mechanical properties5table a.1 creep resistance6en 10213-4:19951 scopeaccording to the general delivery conditions of en 10213-1 this standard specifies the chemical and mechanical requirements to be met under specific inspection of austenitic andaustenitic-ferritic grades.2 normative referencesthis european standard incorporates by dated or undated reference, provisions from other publications. these normative references are cited at the appropriate places in the text and the publications are listed hereafter. for dated references, subsequent amendments to or revisions of any of these publications apply to this european standard only when incorporated in it by amendment or revision. for undated references the latest edition of the publication referred to applies.en 10213-1, technical delivery conditions for steel castings for pressure purposes part 1: general.3 requirements3.1 chemical compositionthe cast analysis shall comply with table 1(see 7.1 of en 10213-1 for permissible deviations and for unspecified elements). for chemical analysis on castings see 8.4.1 of en 10213-1.3.2 heat treatmentheat treatment shall comply with table 2 (see 6.2 of en 10213-1).3.3 mechanical properties3.3.1 the mechanical properties at room, low and elevated temperatures shall comply with table 2. for the conditions of verification on test blocksee 7.2.1 of en 10213-1, and on castings see 7.2.2 and 8.4.2 of en 10213- mechanical properties at elevated temperatures are specified in table 2 but their verification is performed only by agreement (see 7.2.3 of en 10213-1), and on castings(see 7.2.2 and 8.4.2 of en 10213-1).note creep resistance mean values are given, for some grades in annex a table a.1 only for information.licensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsi bsi 12-19983licensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsi4 bsi 12-1998en 10213-4:1995table 1 chemical composition (cast analysis)% (m/m)designationcmax.simax.mnmax.pmax.smax.crmonicuothersnamenumbergx2crni19-11a1.4309a0,0301,502,000,0350,02518,00 to 20,009,00 to 12,00n: 0,20 max.gx5crni19-10a1.4308a0,071,501,500,0400,03018,00 to 20,008,00 to 11,00gx5crninb19-11a1.4552a0,071,501,500,0400,03018,00 to 20,009,00 to 12,00nb: 8 c,max: 1,00gx2crnimo19-11-2a1.4409a0,0301,502,000,0350,02518,00 to 20,002,00 to 2,509,00 to 12,00n: 0,20 max.gx5crnimo19-11-2a1.4408a0,071,501,500,0400,03018,00 to 20,002,00 to 2,509,00 to 12,00gx5crnimonb19-11-2a1.4581a0,071,501,500,0400,03018,00 to 20,002,00 to 2,509,00 to 12,00nb: 8 c,max: 1,00gx2nicrmo28-20-2a1.4458a0,0301,002,000,0350,02519,00 to 22,002,00 to 2,5026,00 to 30,002,00 max.n: 0,20 max.gx2crnimon22-5-31.44700,0301,002,000,0350,02521,00 to 23,002,50 to 3,504,50 to 6,50n: 0,12 to 0,20gx2crnimocun25-6-3-31.45170,0301,001,500,0350,02524,50 to 26,502,50 to 3,505,00 to 7,002,75 to 3,50n: 0,12 to 0,22gx2crnimon26-7-4b1.4469b0,0301,001,000,0350,02525,00 to 27,003,00 to 5,006,00 to 8,001,30 max.n: 0,12 to 0,22a it should be pointed out that the suggested chemical composition ranges of these high alloyed corrosion resistant steel grades are rather large. according to the final destination(high temperature/low temperature, etc.) it may be advisable for the founder to aim for narrower ranges for different elements in order to achieve the most suitable structures. b for this steel grade a minimum value of the “pitting index” may be required as pl = cr + 3,3 mo + 16 n $ 40.licensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsi bsi 12-19985en 10213-4:1995table 2 mechanical propertiesdesignationheat treatmenta+ atacthicknessmm max.tensile test at roomtemperatureimpact testtensile test at elevated temperaturenamenumberrp1,0empai min.rmimpamin.a %min.kvjmin.chrp1,0empai min. at c100200300350400500550gx2crni19-111.43091 050 to 1 150150210440 to 6403080grtg165130110100gx5crni19-101.43081 050 to 1 150150200440 to 6403060grtg160125110gx5crninb19-111.45521 050 to 1 150150200440 to 6402540rt165145130120110100gx2crnimo19-11-21.44091 080 to 1 150150220440 to 6403080grtg175145115105gx5crnimo19-11-21.44081 080 to 1 150150210440 to 6403060grtg170135115105gx5crnimonb19-11-21.45811 080 to 1 150150210440 to 6402540rt185160145130120115gx2nicrmo28-20-21.44581 100 to 1 180150190430 to 6303060grtg165135120110gx2crnimon22-5-31.44701 120 to 1 150bc150420f600 to 8002030rt330f280fdgx3crnimocun25-6-3-31.45171 120 to 1 150bc150480f650 to 8502250grtg390f330fdgx2crnimon26-7-41.44691 140 to 1 180bc150480f650 to 8502250grtg390f330fda the heat treatment for all the steel grades is + at + qw (solution annealing + water quenching).b after solution annealing at high temperature, castings may be cooled down to 1 040 c to 1 010 c prior to water quenching in order to improve corrosion resistance and prevent cracks in complex shapes.c as far as steel castings for pressure vessels are concerned the austenitic-ferritic steels are not considered in their age hardened condition.d for similar reasons as those concerning notec the austenitic-ferritic steels have not to be used for temperatures higher than 250 c in pressure vessel applications. e rp0,2 may be estimated by lowering rp1,0 by 25 mpa.f rp0,2.g for use at low temperatures impact properties may be agreed and the following applies:steel number kv at c jmin.1.4517, 1.446935 701.4308, 1.4408, 1.445860 1961.4309, 1.440970 196 h rt = room temprature.i 1 mpa = 1 n/mm2.en 10213-4:1995licensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsiannex a (informative) creep propertiestable a.1 creep resistance (mean values) sr: rupture stress mpadesignationtemperaturec550600650700namenumbertimeh10 000100 00010 000100 00010 000100 00010 000100 000gx5crni19-101.4308sr14712411083735247gx5crninb19-111.4552sr2461921561241098073gx5crnimo19-11-21.4408sr194160148113103666042 bsi 12-19986blank7licensed copy: institute of technology tallaght, institute of technology, tue aug 29 10:59:19 bst 2006, uncontrolled copy, (c) bsibsi389 chiswick high roadlondonw4 4al| bsi british standards institution| bsi is the independent national body responsible for preparing british standards. it| presents the uk view on standards in europe and at the international level. it is| incorporated by royal charter.| revisions| british standards are updated by amendment or revision. users of british standards| should make sure that they possess the latest amendments or editions.| it is the constant aim of bsi to improve the quality of our products and services. we| would be grateful if anyone finding an inaccuracy or ambiguity while using this| british standard would inform the secretary of the technical committee responsible,| the identity of which can be found on the inside front cover. tel: 020 8996 9000.| fax: 020 8996 7400.| bsi offers members an individual updating service called plus which ensures that| subscribers automatically receive the latest editions of standards.| buying standards| orders for all bsi, international and foreign standards publications should be| addressed to customer services. tel: 020 8996 9001. fax: 020 8996 7001.| in response to orders for international standards, it is bsi policy to supply the bsi| implementation of those that have been published as british standards, unless| otherwise requested.| information on standards| bsi provides a wide range of information on national, european and intern