SLC500與ControlLogix-通過以太網進行通訊配置

1、SLC500與ControlLogix 通過以太網進行通訊配置ControlLogix側通訊MSG配置A）數據讀取配置Message:PLC5 Type ReadSource Element:源數據起始地址(對應500PLC里輸出數據的文件號)。Number Of Elements:數據長度(數據類型為Source Element的類型)Destination Element:目標數據起始地址(數據類型跟Source Element一樣)B）數據寫入配置Message:PLC5 Type WriteSource Element:源數據起始地址 Number Of Elements:數據長度(數

2、據類型為Source Element的類型)Destination Element:目標數據起始地址(500PLC里接收數據文件號)C）路徑配置Path：格式為x,y形式圖示中ENB2為I/O配置里面以太網卡名稱，2為從以太網卡端口退出，192.168.26.22為目標通訊CPU以太網IP地址SLC500側MSG指令配置(可配可不配，配置如下)數據讀取配置Type:Peer-To-PeerRead/Write:ReadTarget Device:PLC5 跟ControlLogix通訊只能使用此類型Local/Remote:LocalControl Block:控制塊，用于存儲MSG指令的各種

3、狀態This Controller 本控制器Communication Command: PLC5 ReadData Table Address:讀取數據存儲的初始地址Size in Elements:數據長度Channel:通道號，以太網通訊選擇1Target Device 目標設備Message Timeout:通訊超時時間設定Data Table Address:從ControlLogix讀取的數據變量起始地址，變量名稱使用雙引號Ethernet (IP) Address:目標設備以太網卡IP地址Local/Remote:LocalMultihop:No 若選擇YES，則Ethernet

4、 (IP) Address項不會出現B）數據寫入配置Type:Peer-To-PeerRead/Write:WriteTarget Device:PLC5 跟ControlLogix通訊只能使用此類型Local/Remote:LocalControl Block:控制塊，用于存儲MSG指令的各種狀態This Controller 本控制器Communication Command: PLC5 WriteData Table Address:寫入數據存儲的初始地址 Size in Elements:數據長度Channel:通道號，以太網通訊選擇1Target Device 目標設備Message Timeout:通訊超時時間設定Data Table Address:從ControlLogix讀取的數據變量起始地址，變量名稱使用雙引號Ethernet (IP) Address:目標設備以太網卡IP地址Local/Remote:LocalMultihop:No 若選擇YES，則Ether