2015下半年春秋檢工卡自定義項目tgpe-ml

1、TGPE-M5721-001LDForm.MP.001 版次Revi00第 1 頁，共 4 頁TitleDetail Inspection of the Sealant Betn the Seal Plate/Acs Panel and theLH wing Top Skrailing EdgeMech.Insp.WARNING: PUT THE SAFETY DEVIAND THE WARNING NOTIINITION BEFORE YOU STARASK ON OR NEAR:THE FLIGHT CONTROLSTHE FLIGHT CONTROL SURFATHE LANDING G

2、EAR AND THE RELATED DOORSCOMPONENTST MOVE.警告：在執行該任務之前把和警告標牌放置到位：飛行飛行面起落架和相關艙門活動WARNING:BE CAREFUL WHEN YOU USE CONSUMABLE MATERIALS. OBEY THE MATERIAL MANUFACTURERS INSTRUCTIONS AND YOUR LOCAL REGULATIONS.警告：謹慎使用消耗件材料。嚴格遵守材料制造廠說明和當?shù)?。Job Set-up工作準備Safety Precautions安全措施Put the safety barriers inition

3、.把安全防護欄放置到位。Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.在襟翼/縫翼控制桿上安裝零位鎖工具(98D27803500001)。Put the WARNING NOTI)he cockpit tols not to operate the flaps, the slats or the ailerons.在駕駛艙放置警告標牌提示不能操作襟翼，縫翼或者副翼。Get acs接近Put the ACS PLATFORM 4M (13 FT)

4、- ADJUSTABLE inition at the applicable zone 500.在對應區域 500 放置 4M (13 FT)可調節接近。TGPE-M5721-001LDForm.MP.001 版次Revi00第 2 頁，共 4 頁TitleDetail Inspection of the Sealant Betn the Seal Plate/Acs Panel and theLH wing Top Skrailing EdgeMech.Insp.Procedure步驟Preparation for inspection(refer to figure 1 for inspe

5、ction area)準備檢查(檢查區域參考圖 1)Use a Material No. 19-003* (L -FREE COTTON CLOTH), made moist with Material No. 11-026* (CLEANING AGENTS) to clean the applicable area for inspection.用不起 CML NO. 19-003*蘸清潔溶劑CML NO. 11-026*清潔檢查區域。Detail Inspection of the Sealant Betn the Seal Plate/Acs Panel and the LH wing

6、 Top Skrailing Edge.詳細檢查上的密封板/接近面板和蒙皮后緣之間的密封膠。Do an inspection and make suret:there is no damagethere are no cracksthere is no corrothe pafinish ishe correct condition.執行檢查并確保：無損傷無裂紋無腐蝕表面漆層完好。Note: If nesary, refer to the SRM 51-76-11 for the correct repair procedure.注釋：視情參照 SRM 51-76-11進行修理。RIIRII檢

7、查結果 (Checking result)采取措施 (Maena nce)TGPE-M5721-001LDForm.MP.001 版次Revi00第 3 頁，共 4 頁TitleDetail Inspection of the Sealant Betn the Seal Plate/Acs Panel and theLH wing Top Skrailing EdgeMech.Insp.Close-up結束Make suret the work area is clean and clear of tool(s) and other items.確保工作區域整潔，無工具和其他設備。Remove

8、 the safety barriers移走安全防護欄。Remove the acs platforms.移走接近。Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) from the flap/slat control lever.從襟翼/縫翼控制桿上取下零位鎖工具(98D27803500001)。.Remove the warning noti)取走警告標牌。Remove the ground support and maenance equipment, the spel and standard tools and all other items.移開地面設備、和標準