惠普Procurve以太網交換機配置的指南Version1.0

1、22/22惠普ProCurve以太網交換機安裝配置指南中國惠普安裝規劃中心產品介紹ProCurve 6120系列交換機分為兩種型號：6120G/XG6120XG產品名稱的規則：以6120產品的G/XG為例，G和XG都指端口速率，其中G表示1Gb per second，XG表示10Gb per second；”/”以前的部分特指部端口速率，”/”以后的部分特指外部端口速率。前面板與端口介紹：端口6120 G/XG6120 XG端口類型端口名稱端口類型端口名稱16x 1GbE Server NIC portsD1-D1616x 10GbE Server NIC ports1-161x 10GbE

2、CX4C11x 10GbE CX4 or 1x 10GbE SFP+（最左側）172x 10GbE XFP portsX1;X25x 10GbE SFP+ ports18;19;20;21;222x 1GbE SFP portsS1;S22x 10GbE SFP+ ports or S2S links（最右側）23;244x 10/100/1000 RJ-45 ports1;2;3;4S2S linkI1Management PortOOBMManagement PortOOBM10GbE CX4The CX4 interface requires the use of copper cabl

3、ing, similar to the variety used in InfiniBand technology, and is designed to work up to a distance of 15m. CX4 technology is an attractive solution because it has the lowest cost per port of all 10Gb interconnects, at the expense of range. CX4 has a bigger form factor than either SFP or SFP+. 10GbE

4、 XFP portsThese 10GbE ports support SR (multi-mode fiber, 300 m) and LR (single-mode fiber, 10 km) optic transceivers based on the XFP version of the small form factor pluggable specification. XFP transceivers have a smaller form factor compared to several standards (XENPAK, X2, XPAK) that preceded

5、it. The XFP ports support Industry Standard Servers (ISS) optics only. 1GbE SFP portsThese 1GbE ports support SX (multi-mode fiber, 550 m) and LX (single-mode fiber, 10 km) optic transceivers based on the SFP version of the small form factor pluggable specification using an LC physical connector. Th

6、ese ports also support 1000BASE-T copper connections using an RJ-45 connector. The SFP ports support ISS and ProCurve optics.10/100/1000 RJ-45 portsThese ports support standard RJ-45 Ethernet cables and each port can operate at one of three autosensing speeds.5x 10GbE SFP+ portsThese five ports are

7、dedicated10GbE SFP+ ports that support SR (multi-mode fiber, 300 m), LR (single-mode fiber, 10 km), and LRM (multi-mode fiber, 220 m) optic SFP+ transceivers.2x 10GbE SFP+ portsIndividually, the two ports labeled 23 and 24 can be used as either external 10GbE SFP+ ports or internal 10GbE switch-to-s

8、witch (cross-link) ports. For SFP+ connectivity, these ports support the same fiber optic transceivers as the other SFP+ ports.Internal Network PortsThe 6120G/XG also has “internal” Ethernet ports that function as downlinks to devices in the enclosure. The internals ports are essentially communicati

9、on interfaces used to transfer data to and from server blades, storage blades, and even another 6120G/XG (if it is installed in an adjacent bay of the enclosure). The internal ports use the enclosures midplane circuitry to communicate with the other c-Class enclosure components.Management PortThe IP

10、 address within the OA subnet that you assign to the blade switch is used by a switch component known as Out-Of-Band Management (OOBM).交換機系統指示燈：Module status LED：綠色表示交換機工作正常；橙色表示有故障Module locator LED：用戶可以通過命令chassislocate 來控制其狀態，方便用戶找到此交換機端口指示燈介紹：Link status LED：綠色表示已連接；橙色表示有故障Link activity LED綠色閃爍表

11、示正在通訊RJ-45指示燈綠色閃爍表示端口正在10/100Mb per second速率通訊橙色閃爍表示端口正在1000Mb per second速率通訊管理口介紹：Mini USB接口，交換機產品包裝里都有對應的線纜；使用其管理交換機時，需要先安裝相應的驅動程序，并通過終端模擬器軟件訪問。驅動程序如下 HYPERLINK :/h20000.www2.hp /bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=3709945&prodSeriesId=3979968&prodNameId=3979969

12、&swEnvOID=1093&swLang=13&mode=2&taskId=135&swItem=MTX-0fab69bfedd14cddbfa832f02a USB Console Driver for HP ProCurve 6120 Series Ethernet Blade Switches for WindowsClear and Reset Control Buttons：Clear用來清除用戶密碼；Reset使交換機重啟；當Clear和Reset同時按，將使交換機恢復出廠配置配置細則：管理接口ProCurve 6120系列交換機管理接口有三個：Mini USB模擬串口，與OA直

13、連的部串口，與OA直連的Out-Of-Band Management (OOBM)以太網接口Mini USB訪問Mini USB分別連接交換機和PC的USB接口，安裝驅動后，在終端模擬器軟件中選擇連接端口COM4，串口屬性9600/n/8/1OA部串口訪問telnet connect interconnect 通過以上兩種串口訪問方式可以配置OOBM以太網接口的IP地址OOBM以太網接口可以用telnet 訪問，或者用IE 訪問。建議在做配置時使用telnet 方式。這樣的好處是：1命令行方式便于把事先制訂好的配置腳本粘貼到終端上執行2避免了IE 方式可能遇到的Java 版本問題，Java 響

14、應速度慢的問題常用交換機參數配置OOBM端口管理方法：端口啟用/禁用（默認情況下是啟用狀態）ProCurve# configure ProCurve(config)# oobmProCurve(oobm)# enable #啟用ProCurve(oobm)# disable#禁用DHCP獲取IPProCurve# configure ProCurve(config)# oobmProCurve(oobm)# ip address dhcp-bootp手工指定IPProCurve# configure ProCurve(config)# oobmProCurve(oobm)# ip addres

15、s # IP-ADDR指32位IP地址的十進制表示；MASK-LENGTH指子網掩碼的二進制表示中”1”的個數(如子網掩碼是“”，在這里可以直接寫24)配置網關ProCurve# configure ProCurve(config)# oobmProCurve(oobm)# ip default-gateway用戶管理交換機默認有manager和operator兩個用戶，默認密碼為空。修改密碼ProCurve# configure ProCurve(config)# password manager New password for manager: Please retype new pas

16、sword for manager:ProCurve(config)#password operator New password for operator: Please retype new password for operator:修改系統名稱ProCurve# configure ProCurve(config)# hostname TTETTE(config)#前面板恢復出廠按鈕的啟用/禁用ProCurve(config)# front-panel-security factory-reset Enable/Disable factory-reset ability passwor

17、d-clear Enable/Disable password clear password-recovery Enable/Disable password recovery.清空配置文件ProCurve# erase startup-config保持配置到交換機ProCurve# write memory保持配置到TFTP服務器ProCurve# copy running-config tftp 常用交換機狀態查看查看固件版本ProCurve# show flashProCurve# show version查看當前配置文件ProCurve# show running-config查看端口

18、狀態ProCurve# show interfaces 查看OOBM狀態ProCurve# show oobm查看VLAN狀態ProCurve# show vlans查看交換機系統ProCurve# show system查看交換機日志ProCurve# show tech allProCurve# show logging常用交換機應用配置配置VLAN與VLAN taggingProCurve# configureProCurve(config)# vlan 10#建立Vlan 10ProCurve (vlan-10)# name train_the_engineer#為Vlan 10命名P

19、roCurve# show vlans 10#顯示所有vlan信息，可以發現Vlan 10名稱已經成功更改TaggedProCurve (vlan-10)# tagged ethernet D1-D4#將端口D1到D4加入到新的vlanProCurve# show vlans 10#顯示vlan 10狀態，可以發現D1到D4端口已經成功加入vlan 10ProCurve# show running-config#顯示當前配置，可以發現D1到D4端口不但屬于vlan 10，同時屬于DEFAULT_VLAN(Vlan 1)UntaggedProCurve (vlan-10)# untagged e

20、thernet D1-D4#將端口D1到D4加入到新的vlanProCurve# show vlans 10#顯示vlan 10狀態，可以發現D1到D4端口已經成功加入vlan 10ProCurve# show running-config#顯示當前配置，可以發現D1到D4端口只屬于vlan 10VLAN與Trunk配置實例注意以下配置要按順序執行ProCurve# configureProCurve(config)# interfaces ethernet 1-4 #進入端口1-4配置模式ProCurve (eth-1-4)# lacp active#選擇LACP協議模式為”active”ProCurve(eth-1-4)# end ProCurve# configureProCurve(config)#trunk ethernet 1-4 trk8 lacp#將端口1到4加入到Trunk Group 8中，同時啟用LACP協議協商；同一Trunk Group中所有端口的LACP mode必須一致ProCurve(config)# vlan 2ProCurve (vlan-2)# tagged ethernet 1-4#將端口1到4加入到vlan 2，這里不能用”untagged”