_MTK校準配置文件參數詳細說明要點

1、4.1 INI文件的介紹：4. 1. 1射頻功能組的復位下面是setup INI文件中定義的項目。GSM900 Sig = 1GSM1800 Sig = 1GSM1900 Sig = 1GSM900 NSig = 1GSM1800 NSig = 1GSM1900 NSig = 1通常設置為1,指在對CMU200設置之前對設備進行復位，為 0時不復位。1 . 2系統設置：setup INI文件中定義的項目：External Reference Clock = 0 默認值為0,指使用CMU200輸出的參考時鐘， 為1時使用 外部參考時鐘。CMU Base GPIB Address = 20CMU的

2、GPIB地址的設置，要與軟件對應。Instrument = CMU200使用的設備為CMU200Power Supply Address = GPIB0:5:INSTR電源地址的設置使用 Kei230 x 時，應為 Power Supply Address = 5CMU RF Port = 2CMU200使用的射頻端口設置Test Mode = 0設為0指需要手動對設備進行初始化，1指在綜測時軟件將自動對設備進行初始化，2指在校準時軟件將自動對設備進行初始化，3指在校準和綜測聯合測試時軟件將自動對設備進行初始化FDM database file = c:Program FilesMTK_ate

3、demoreportBPLGUInfoCustomDatabase文件的存放路徑，必須與手機軟件對應Calibration file = c:Program FilesWMTK_atedemoWMTKCAL_6205B.INI校準初始默認值設置文件的路徑Config file = c:Program FilesMTK_atedemometa_6205B.CFG關于校準的設置，如校準的信道，限制同最大、最小值一Report file path = c:Program FilesMTK_atedemoreport_6218B TOC o 1-5 h z 測試報告的存儲路徑一一Database fi

4、le = c:Program FilesWMTK_atedemoWReport_StatisticsW6218B_statistics.xls測試結果文件的存放路徑一一一IMSI = 001010123456789SIM卡中的IMSI號的設置POWER ON AFTER CHANGE = 1聯合測試時，如果設備改變不同狀態時較慢，則設置為1Stability Count = 1循環測試的次數設置Fixture COM port = 1串口地址設置System Cable Loss Calibration = 0校準系統的線損選擇1. 3呼叫建立設置Setup Network = 1建立呼叫時的

5、網絡設置， 1指GSM頻段，2指DCS頻段，3指PCS頻段GSM Call Setup Channel = 1建立呼叫的信道號設置GSM BCCH Channel = 32廣播控制信道的設置DCS Call Setup Channel = 512DCS建立呼叫的信道設置DCS BCCH Channel = 700DCS廣播控制信道的設置PCS Call Setup Channel = 512PCS建立呼叫的信道設置PCS BCCH Channel = 700PCS廣播控制信道的設置GSM850 Call Setup Channel = 128GSM850建立呼叫的信道設置GSM850 BCCH

6、 Channel = 128GSM850廣播控制信道的設置BCCH RF LEVEL = -60下行廣播控制信道電平BS TCH LEVEL = -80.5基站業務信道電平Triple Band = 0設置為1時要進行PCS的測試DCS Band = 1為1指綜測時要測DCSGSM Band = 1為1指綜測時要測 GSMGSM850 Band = 0為1時，綜測要測 GSM850GPRS TEST = 0為1時要進行GPRS的測試4.1.4信令測試Power Measment Burst = 10定義功率測試時，要測的 Burst的數量Average Burst Power = 1為1指要進

7、行平均功率的測試Peak Burst Power = 1為1指要進行峰值功率的測試PVT Match = 1為1指進行功率時間模板測試Modulation Measment Burst = 10定義調制頻譜測試時所要測試的Burst數量Phase Error Peak = 1為1指要進行相位峰值誤差的測試Phase Error RMS = 1為1指要進行相位均方值誤差的測試Frequency Error = 1為1指要進行頻率誤差的測試ORFS MOD Burst = 10定義調制頻譜測試時，所要測試的Burst的數量Spectrum Modulation = 1為1指要進行調制頻譜的測試OR

8、FS Switch Burst = 10定義開關頻譜測試時，所要測試的Burst的數量Spectrum Switch = 1為1指要進行開關頻譜的測試Rx Quality = 0是否進行接收質量的測試RX Level = 0是否進行接收電平的測試RFER = 0是否進行誤碼率的測試BBB = 0是否進行Bust By Burst的誤碼率測試GSM Rx Meas Level = -100定義GSM測試誤碼率時的下行功率DCS Rx Meas Level = -100定義DCS測試誤碼率時的下行功率PCS Rx Meas Level = -100 定義PCS測試誤碼率時的下行功率Rx RFER

9、Burst = 128定義測試時的Burst數量Rx BBB Burst = 88定義Bust By Burst的誤碼率測試時，要測的 Burst數量GSM Output Loss = 0.6GSM輸出補償設置GSM Input Loss = 0.6GSM輸入補償?shù)脑O(shè)置DCS Out Loss = 1.2DCS輸出補償?shù)脑O(shè)置DCS Inp Loss = 1.2DCS輸入補償?shù)脑O(shè)置PCS Out Loss = 1.3PCS輸出補償?shù)脑O(shè)置PCS Inp Loss = 1.3PCS輸入補償?shù)脑O(shè)置Location update timeout = 50位置更新的延時設置Timing Error Lim

10、it = 5(bit)時間提前量的限制設置RX Level Limit = 27接收電平的限制設置RX Quality Limit = 3接收質量的限制設置Stop Condition = 0停止條件的設置，為0指無論中間的測試項目是否通過，都要繼續進行測試，直到測試結束，為1指當有測試Fail的項目時，則停止測試Version New = 0當使用的綜測儀的版本大于 3.5時，或RAM256M 時，可以設為1,以設置其進行并行 的測試，舊版本設為1時將增加測試時間Final Test With Calibration = 1設為1指進行綜測和校準的聯合測試Wireless Test = 0為

11、1指進行耦合測試Get Barcode = 1讀取并檢查板測狀態RX ClassII Limit = 1.5接收誤碼率ClassII的限制設置RX ClassIb Limit = 1.5接收誤碼率ClassIb的限制設置Default Test Items = 1綜測提供了兩種模式，為 1時，將按照Signalling Measurement中的定義進行測試, 為0時將按照GSM xx中的設置進行測試Check BarCode Delay = 15.0檢測板號延時設置（綜測前檢測板測是否通過時，要進行板號的讀?。〩andover Delay Time = 0.5測試頻段Handover的延時設

12、置BER MEAS MODE = 0為0時進行單時隙的測試，為 1時將進行連續時隙的測試BER Continuous Meas Delay = 1.5定義Ber連續測試模式的測試延時Mobile Report RxQ Delay = 1.5接收質量測試的延時設置，（延時以便得到正確的移動臺測試值）MT Call = 0為0時手機將撥號112以進行呼叫建立，為1時，指設備將呼叫移動臺進行通信連 接GSM850 Rx Meas Level = -100當default testing items”為1時，ATE將使用此值進行 BER的測試6218B Normal Baud Rate = 11520

13、0定義6218B的通信波特率6205B Normal Baud Rate = 57600定義6205B的通信波特率RX Level Limit MAX = 31接收電平的最大值設置1 . 5校準設置GSMN OUT LOSS = 0.6非信令模式下GSM的輸出損耗設置GSMN INP LOSS = 0.6非信令模式下GSM的輸入損耗設置DCSN OUT LOSS = 1.2非信令模式下DCS的輸出損耗設置DCSN INP LOSS = 1.2非信令模式下DCS的輸入損耗設置COM PORT = 4串口端口設置Auto Barcode = 0為1時，軟件將自動生成板號Auto Barcode S

14、tep = 1板號自動生成時的增加步長設置ADC Calibration = 0為1將進行ADC的校準Frequency Bank with PCS = 0定義是否進行PCS頻段的校準BB Chip Type = 6205B定義芯片類型CO GSM900 = 70從CFG文件中讀取GSM校準信道的值CO DCS1800 = 700從CFG文件中讀取DCS校準信道的值CO PCS1900 = 660從CFG文件中讀取PCS校準信道的值PCSN OUT LOSS = 1.3設置非信令模式下測試PCS時的輸出線損I PCSN INP LOSS = 1.3設置非信令模式下測試PCS時的輸入線損I En

15、ter META Mode Timeout = 10000設置進入META模式的延時I Enter META Timer Delay = 2.0校準時，當電源控制異常時，可以調整此項設置AFC Calibration = 1為1時將進行AFC校準Pathloss Calibration = 1為1時將進行路徑損耗校準APC Calibration = 1是否進行APC校準I APC Check = 1為1時將進行APC的檢測Frequency Bank with GSM850 = 0為1時將進行GSM850的校準Frequency Bank with GSM900 = 1為1時將進行GSM90

16、0的校準Frequency Bank with DCS1800 = 1為1時將進行GSM1800的校準Add Calibration Status = 1為1時將把校準結果加入條碼的60, 61位如：PASS : char60= 1 , char61= 0FAIL : char60= 0, char61= 11. 6 IMEI 設置 Scan IMEI = 0為1時，可以使用掃描儀掃描條碼，軟件會將IMEI號寫入手機1. 7綜測發射測試檢測：下面是CFG文件中定義的綜測和校準PCL限制表：GSM900_MAX_P6.0,8.0,10.0,12.0,13.8,15.8,17.8,19.8,21.

17、8,23.8,25.8,27.8,29.5,31.0,32.9,”GSM900_MIN_P4.0,6.0,8.0,10.0,12.5,14.5,16.5,18.5,20.5,22.5,24.5,26.5,28.5,30.0,31.7,DCS1800_MAX_P2.0,3.5,5.0,7.0,9.0,11.0,12.5,14.5,16.5,18.5,20.5,22.5,24.5,26.5,28.0,31.0,DCS1800_MIN_P0.0,1.5,3.5,5.0,7.0,9.0,11.5,13.5,15.5,17.5,19.5,21.5,23.5,25.0,27.0,28.7,PCS1900_

18、MAX_P0.5,2.5,4.5,6.5,8.5,10.5,12.5,14.5,16.5,18.5,20.5,22.5,24.5,26.5,28.5,30.5,PCS1900_MIN_P-0.5,1.5,3.5,5.5,7.5,9.5,11.5,13.5,15.5,17.5,19.5,21.5,23.5,25.5,27.5,29.5,頻率和相位誤差的限制表：GSM_Freq_Error_Limit = 90DCS_Freq_Error_Limit = 180PCS_Freq_Error_Limit = 190Phase_Error_Peak_Limit = 20Phase_Error_RMS_

19、Limit = 5Spectrum due to switching enable = 1,0,0,1,開關頻譜和調制頻譜的偏移量的定義：1,0,0,1,指使用+/- 400k和+/-1.8M的偏移量進行測試Spectrum due to Switching +400kHz=-31.182460Spectrum due to Switching -400kHz=-29.590330Spectrum due to Switching +600kHz=-35.207820Spectrum due to Switching -600kHz=-32.279390Spectrum due to Swit

20、ching +1.2MkHz=-34.092160Spectrum due to Switching -1.2MkHz=-38.503780Spectrum due to Switching +1.8MHz=-43.583010Spectrum due to Switching -1.8MHz=-46.116880Spectrum due to modulation enable = 0,0,0,1,0,0,0,0,0,0,1,Spectrum due to Modulation +100kHz=-8.557312Spectrum due to Modulation -100kHz=-8.77

21、7496Spectrum due to Modulation +200kHz=-34.214780Spectrum due to Modulation -200kHz=-34.015660Spectrum due to Modulation +250kHz=-39.874850Spectrum due to Modulation -250kHz=-38.849580Spectrum due to Modulation +400kHz=-61.613100Spectrum due to Modulation -400kHz=-62.010590Spectrum due to Modulation

22、 +600kHz=-66.382050Spectrum due to Modulation -600kHz=-66.253600Spectrum due to Modulation +800kHz=-66.471500Spectrum due to Modulation -800kHz=-67.809330Spectrum due to Modulation +1MHz= -68.384120Spectrum due to Modulation -1MHz= -68.194400Spectrum due to Modulation +1.2MHz=-69.887570Spectrum due

23、to Modulation -1.2MHz=-71.136630Spectrum due to Modulation +1.4MHz=-73.157710Spectrum due to Modulation -1.4MkHz=-72.516720Spectrum due to Modulation +1.6MHz=-74.163570Spectrum due to Modulation -1.6MHz=-76.117770Spectrum due to Modulation +1.8MHz=-76.022610Spectrum due to Modulation -1.8MHz=-78.223

24、210Spectrum due to switch limit = -10.0,-10.0,-21.0,-21.0,-21.0,-21.0,-24.0,-24.0, 開關頻譜的限制值 Spectrum due to modulation limit Line00010.5,0.5,-300,-300,-33.0,-33.0,-55.0,-55.0,-60.0,-60.0,-60.0,-60.0,-60.0,-60.0,”調制頻譜的限制值4. 1.板號 Barcode = S4716A000700定義板號的起始值 Barcode Limit = MT012345678901234569濾除未定義

25、的板號，檢測寫入的板號位數。1. 9測試報告Part Number = MTK_6205BBatch = 02Revision = W04.24Serial Number = 000001以上是加入測試報告的信息1. 10錯誤代碼（錯誤代碼可以自己定義）Lacation update Fail = 101MT Call Fail = 102Call Drop = 103綜測錯誤代碼Average Burst Power Fail = 104Peak Burst Power Fail = 105PVT Match Fail = 106Timing Error Fail = 107Phase Er

26、ror Peak Fail = 108Phase Error RMS Fail = 109Frequency Error Fail = 110Spectrum due to Modulation Fail = 111Spectrum due to Switching Fail = 112Rx Quality Fail = 113Rx Level Fail = 114BER Fail = 115META DLL的錯誤代碼METAAPP_GET_A VAILABLE_HANDLE_FAIL = 201METAAPP_OPEN_UART_FAIL = 202METAAPP_CLOSE_UART_FA

27、IL = 203METAAPP_BOOT_FAIL = 204METAAPP_BOOT_STOP_FAIL = 205METAAPP_INIT_FAIL = 206METAAPP_W AIT_FOR_TARGET_READY_FAIL = 207METAAPP_COMM_SET_BAUD_RA TE_FAIL = 208METAAPP_COMM_START_FAIL = 209METAAPP_COMM_STOP_FAIL = 210METAAPP_CONNECT_WITH_TARGET_FAIL = 211METAAPP_DISCONNECT_WITH_TARGET_FAIL = 212MET

28、AAPP_RF_SELECT_BAND_FAIL = 213METAAPP_RF_SELECT_BAND_CNF_FAIL = 214METAAPP_RF_AFC_MEASURE_FAIL = 215METAAPP_RF_AFC_MEASURE_CNF_FAIL = 216METAAPP_RF_AFC_SET_DAC_V ALUE_FAIL = 217METAAPP_RF_AFC_SET_DAC_V ALUE_CNF_FAIL = 218METAAPP_RF_PM_FAIL = 219METAAPP_RF_NB_TX_FAIL = 220METAAPP_RF_NB_TX_CNF_FAIL =

29、221METAAPP_RF_SET_APC_LEVEL_DAC_FAIL = 222METAAPP_RF_SET_APC_LEVEL_DAC_CNF_FAIL = 223METAAPP_RF_STOP_FAIL = 224METAAPP_RF_STOP_CNF_FAIL = 225METAAPP_NVRAM_INIT_FAIL = 226METAAPP_NVRAM_AFC_SLOPE_INV ALID_FAIL = 227METAAPP_NVRAM_AGC_PATHLOSS_LEN_FAIL = 228METAAPP_NVRAM_GET_REC_LEN_FAIL = 229METAAPP_NV

30、RAM_GET_RAMPTABLE_LEN_FAIL = 230METAAPP_NVRAM_COMPOSE_AGC_PATHLOSS_FAIL = 231METAAPP_NVRAM_DECOMPOSE_AGC_PATHLOSS_FAIL = 232METAAPP_NVRAM_COMPOSE_RAMPTABLE_FAIL = 233METAAPP_NVRAM_DECOMPOSE_RAMPTABLE_FAIL = 234METAAPP_NVRAM_SET_REC_FIELD_V ALUE_FAIL = 235METAAPP_NVRAM_GET_REC_FIELD_V ALUE_FAIL = 236

31、METAAPP_NVRAM_COMPOSE_ADC_CAL_TABLE_FAIL = 237METAAPP_NVRAM_DECOMPOSE_ADC_CAL_TABLE_FAIL = 238METAAPP_NVRAM_COMPOSE_BARCODE_FAIL = 239METAAPP_NVRAM_DECOMPOSE_BARCODE_FAIL = 240METAAPP_NVRAM_COMPOSE_IMEI_FAIL = 241METAAPP_NVRAM_DECOMPOSE_IMEI_FAIL = 242METAAPP_NVRAM_WRITE_FAIL = 243METAAPP_NVRAM_WRIT

32、E_CNF_FAIL = 244METAAPP_NVRAM_READ_FAIL = 245METAAPP_NVRAM_READ_CNF_FAIL = 246METAAPP_FILE_READ_FAIL = 247METAAPP_FILE_WRITE_FAIL = 248METAAPP_IMEI_CALCULATE_CD_FAIL = 249METAAPP_ADC_READ_FROM_NVRAM_CNF_FAIL = 250METAAPP_ADC_MEASURE_FAIL = 251METAAPP_ADC_MEASURE_CNF_FAIL = 252METAAPP_TIMEOUT_FAIL =

33、253校準信息代碼AFC Calibration Fail = 254Pathloss Calibration Fail = 255APC Calibration Fail = 256ADC Calibration Fail = 2571. 11 GSM xxx 如下進行測試信道的定義。GSM 1Active = 1TCH = 3PCL = 5Output Loss = 1.6Input Loss = 0.3Average Burst Power = 1Peak Burst Power = 1PVT Match = 1Timing Error = 1Phase Error Peak = 1Ph

34、ase Error RMS = 1Frequency Error = 1Spectrum Modulation = 1Spectrum Switch = 1Rx Quality = 1RX Level = 1RFER = 0BBB = 1Gold Sample Average Power = 32.2Gold Sample Rx Level = 29The output loss BER measurement level = -104BS TCH level = -77RX Level Max Limit = 35RX Level Min Limit = 27DCS 1Active = 1T

35、CH = 62PCL = 10Output Loss = 0.6Input Loss = 0.46Average Burst Power = 1Peak Burst Power = 1PVT Match = 1Timing Error = 1Phase Error Peak = 1Phase Error RMS = 1Frequency Error = 1定義業務信道定義功率等級定義線損進行平均功率測試進行峰值功率測試進行功率時間模板測試進行時間提前量的測試進行相位峰值的測試進行相位均方根誤差的測試 進行頻率的測試進行調制頻譜的測試進行開關頻譜的測試進行接收質量的測試 進行接收電平的測試 進行

36、誤碼率的測試進彳T BBB的誤碼率測試 金機平均功率值金機接收電平值BER測試的下行電平值定義基站業務信道電平 定義接收電平的最大值限制定義接收電平的最小值限制Spectrum Modulation = 1Spectrum Switch = 1Rx Quality = 1RX Level = 1RFER = 0BBB = 1Gold Sample Average Power = 23.0Gold Sample Rx Level = 29BER measurement level = -103BS TCH level = -78RX Level Max Limit = 33RX Level Mi

37、n Limit = 27ATE用戶接口介紹以下是該測試系統的主界面，該程序主要用于生產線測試，而非研發，所以只包括了一 些你現在在界面上看到的簡單的幾項：錯誤代碼顯示，測試項目動態顯示，大屏幕Fail和Pass測試進度條，查看測試報告的按鈕，打開excel （logging to Excel ）,測試模式選擇按鈕，初始化按鈕，條碼（barcode）顯示及測試信息等。ATE 深入Report & System setting（報告及系統設置）如果你按下report and system seting按鈕，你就能看到這個界面，包括 4部分：左上 部分，你可以看到測試報告信息輸入部分；左邊中間部分，

38、是可選項，你可以選擇相應的功能，用來編輯你的setup INI文件；右上部分，定義了硬件設置；界面底部是非常重要的一部分， 你必須首先在 select test setup中選擇一個 setup INI文件，象MTK_6205B_SETUP.INI文件, 這些文件分別記錄你的NVRAM 數據庫文件、校準文件、CFG文件、還有你的測試報告的位置注意：setup INI文件位置存儲在 customer_setup.txt文件中，如果你選擇了一個錯誤的-ig xisetup INI文件，請手動編輯該文件，輸入正確的setup INI文件位置R Unit Under Tesi瓢1肘訕i路師c頁的Bat

39、ch |02RZi胸標SenftlN umbel |000001Em Me |MTK1254567ft90TESTMODE SELECT|Manuel ImbeJVI；就“T;4訥港匚疝1戶知,市：WWWVWV：a_aWWWWVnaWVWWra_aWWWWWUWWWWaj*WVVW_a：WWVVWVVWVVWVWXr GPRS TestI- Fest Foer Measuremsnt (CMU 3.50)I- Wireless testR GSM Default Test Ite ms PCS CalibrahoiiF PCS RFFinMTesi7 Stop ConditionI- RF F

40、inal Test with Check Bar Code ADC CalibrationPower Supply Type lAgilent 653xxRadio Coinniuiijcflitioii Tester|Ant9960Essebind Chip Type |62QTCMU Measurement PortCMU 如口 COM Ptort Select|COMdPowerSuppl GPIB Addres GP1B:16.:INSTRNVRAM Database file|c APragjani FilesM TK_ated&inoMVR AMBPLGUInfQCustomjO4

41、21 ,MSConfig File Location|c：ProstMnFilftTK _atedemoiMla_6205B.CI：tjCftlibrataon File LocationpPioramFilflsMTK_#tBdfmoMTKCAL_6205B.INITest Setup File Location|cVrogxam FilfisMTK_atedemoMTK_6205E_SETUP.iniTest Report Locainn把巾尊8m FilesMTE)ite(kmo癡pnrtReport D&Ubase Location|cVragjFilesMfK_&tedemofi21

42、8B_statistics.xls -.Select NVRAM Database f&.Select Conlig File.StlectCfldibradonirJI.Selfift Test Setup File.Selecl Tsst Report Location.Select Test Database Location綜測設置 當你完成了 report and system設置之后，你就可以從主界面頂部選擇configuration ,你后看到一下界面：你可以將其與 setup INI文件映射，注意，如果你的設置是wireless test,并且設備是CMU200，右邊底部是設置

43、 cable 10ss （線損補償） 的位置，如果你的設置是 default test items , 將按找默認的測試項進行測試，除非你設置為非default test items（非默認測試項 default testitems=0）,這種情況下測試項為 setup INI文件中定義的信道（如定義在 GSM *節中的）4.2.4測試序列編輯你可以從開始（程式集start）囪口打開，如下所示：Micio領ft Visual C+ 6.0MTK atedenoCvsiome 仁能tup文件定的性享Q1H明回孰行Ilatucinal InstrumentsWinRAR附屏藤用程式Microsof

44、t AccessMaui META ver 3.5.04Borland C+Euilder6El ElitTestSe(iuene哥1 MTK_atBdemo 裁 1 6218B ttetistic?NationalIiistninienteLabVIEW 7.1當打開 EditTestSequence （編輯測試序列）窗體后，你可以看到如下界面，請先選擇setup文件，因?yàn)樗械?TX limit（發射限制）,system delay time（系統延時）,PCL Limit（功率 控制等級限制）等等都定義在這里ATE 軟件與 META軟件的功能對比一下列出了一些相對于 META的不同功能：

45、1、PASS和FAIL大屏幕顯示2、測試進度條3、動態測試狀態顯示4、自動產生測試報告5、綜測試時檢查 check bar6、綜測試包含GSM/GPRS測試7、板測校準和綜測組合模式8、自動生成日志到 Excel9、電源支持NGSM不同類型的線損補償靈活的setuo INI文件可進行測試配置系統錯誤代碼4.4結果和測試報告格式測試狀態顯示PASS當測試通過時顯示該狀態FRIL當測試失敗時會顯示該狀態當正在進行綜測時會顯示該狀態Z E E E : EIE當正在進行校準時會顯示該狀態TERRIHfiTE當按下terminate （中止） 按鈕時會顯示該狀態測試報告格式Part Nunber: SG

46、6110 Serial Huuber: HTK00000001 Reuision: WON.06Batch: 01 Bar Code: MT012345678901234567GSN Band TCH , PCIGSN900 Dand Test 0 ChannelsGSH Band TCH 3, PCL 5Aug. Burst Power (Aug.)dBm = 32.086490PassPeak Burst PowerdBm = 32.239720PassBurst Power Hatching= OPassMaxinun phase error peak deg = -3.922119Pa

47、ssHaxinun phase error RMS deg = 1.348486PassHaxinun frequecy error Hz s -12.530B00Passlining Aduance error 1.000000PassClass II 0.000000PassClass lb - 0.080000PassGSH Band TCH 62, PCL 10Aug. Burst Power (Aug.)dBm 23.060990PassPeak Burst PowerdBm - 23.1928如PassBurst Power Hatching- 0PassS Microsoft E

48、xcel-6218B_$tati$ticsxl$回檎案（E娘翰檢稅描入格式工具資料也）S（W） 52明但）-|g|x|能冠全部占上項目.底口0月,Z 為 打 幽回 V I MSSansSenfA?Confidential A Confidential B Internal UseHlrJ =lIA BcDEF1Bar Coda NumberMT01234567890123-DateTimeCdlibtutiu* r.jilFinal Test FailError Code207-08-200417:46:220003MT01234567890123 07-08-200417:48:300001

49、4MT01234567890123,07-08-200417:51:050005MT01234567890123,07-08-200417:53:0710256671一二 MXtoly1J就精I(xiàn)rNUM1 -L5 GSM測試項GSM標準測試項(R&S CMU200為例)以下時GSM的標準測試項，測試手機必須進入signaling測試模式下位置更新測試(MT CALL )當進行位置更新時，CMU200會產生BCCH與手機進行通信，手機必須在son后開機, 否則位置更新會失敗注意：請確保手機有測試SIM卡TX 測試平均功率測試峰值功率測試(3)功率時間模板測試時間提前量檢測相位峰值誤差測量相位均方差(Phrase Error RMS)測量頻率誤