利用按鍵操作數碼管顯示

1、實驗功能：兩位數碼管顯示功能。具體功能描述如下：數碼管可以顯示0-99兩位數字，按一下加按鍵，數字加1；按一下減按鍵，數字減1。按下清零按鍵，數字清零。程序：/*- *該程序?qū)崿F(xiàn)的是利用單片機實現兩位數碼管顯示功能。具體功能描述如下： *數碼管可以顯示0-99兩位數字，按一下加按鍵，數字加1；按一下減按鍵，數字減1 *此外為了方便，還添加了一個清零按鈕，按下清零按鈕計數歸零。 *-*/#include <reg51.h>#define unchar unsigned char/宏定義#define open 0#define close 1void delayms(char m);

2、/延時函數聲明void display();/數碼管顯示函數聲明sbit up = P22;/加一按鈕sbit down = P23;/減一按鈕sbit clear = P24;/清零按鈕sbit Ledshi = P20;/十位數碼管使能端sbit Ledge = P21;/個位數碼管使能端unchar LedCode=/數碼管真值表0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90;char count = 0;char ge = 0;char shi = 0;void digitalTube()if(clear = 0)delayms(10

3、);/按鍵消抖，是因?yàn)閷?shí)際中按鍵剛剛被按下時電平抖動不穩定，延時10ms讓電平穩定下來再次判斷即可if(clear = 0)count = 0;while(clear = 0)/松手檢測display();if(up = 0)delayms(10);if(up = 0)count+;if(count = 100)count = 0;while(up = 0)/松手檢測display();if(down = 0)delayms(10);if(down = 0)count-;if(count = (-1)count = 99;while(down = 0)display();display();void display()/計算各數碼管顯示的數值ge = count%10;shi = count/10;/關閉數碼管使能端，防止亂入Ledge = close;Ledshi = close;/輪流導通兩位數碼管P0 = LedCodege;Ledge = open;/打開個位數碼管delayms(1);Ledge = close;P0 = LedCodeshi;Ledshi = open;delayms(1);Ledshi = close;void delayms(char m)/延時m毫秒char