避障機器人紅外測距模塊設計與調試

1、避障機器人紅外測距模塊設計與調試一、實訓目的1、了解模數轉換器的基本功能;2、了解紅外測距模塊的基本功能及技術規格;3、掌握紅外傳感器工作原理。 二、實訓設備1 硬件：HOST機一臺、基于機器人項目驅動的嵌入式教學實訓平臺一套；2 軟件：Siliconlab IDE開發環境、調試器。三、實訓原理紅外距離感應模塊是專為機器人設計的測障傳感器，如圖所示。它通過發射紅外線并測量紅外線被反射的強度來輸出反映和物體距離的電壓信號，有效距離 1080厘米。紅外測距傳感器紅外測距功能編號名稱/功能1VCC 電源線2GND 地線3Vo 輸出信號線4發射管5接收管紅外傳感器基于三角測量原理。紅外發射器按照一定的

2、角度發射紅外光束，當遇到物體以后，光束會反射回來，如圖所示。反射回來的紅外光線被CCD檢測器檢測到以后，會獲得一個偏移值L，利用三角關系，在知道了發射角度a，偏移距L，中心矩X，以及濾鏡的焦距f以后，傳感器到物體的距離D就可以通過幾何關系計算出來了。四、實訓步驟1、正確連接PC 機、調試器和嵌入式教學實訓平臺，連接紅外測距模塊；2、打開嵌入式教學實訓平臺電源；3、打開工程，編譯、鏈接、進入調試、運行程序，觀察lcd屏上顯示的測量值，移動機器人，觀察lcd屏上測量值的變化（思考測量值的變化的原理）4、測量傳感器的輸出特性曲線。 在實驗中需要中的函數及功能說明函數名：unsigned char G

3、etIR_Distance(unsigned char channle)函數說明：獲取紅外傳感器感測距離函數名：void ADC_PortInit()函數說明：ADC引腳初始化函數名：void ADC_Init()函數說明：ADC初始化函數名：unsigned char ADC_DistanceGet(unsigned char AD_port)函數說明：獲取AD_port端口紅外傳感器的值函數名：void ADC_ConvertStart()函數說明：AD轉換啟動函數名：void AD_PortSelection(AD_port)函數說明：AD轉換端口配置函數名：unsigned int A

4、DC_AvrDataGet(unsigned int *AD_data)函數說明：獲取平均值函數名：double SensorDistanceProcess(double x )函數說明：ADC值距離轉換#include "Sensor_AD.h"#define AD_NUM 10/*/! 函數名：unsigned char GetIR_Distance(unsigned char channle)/! 函數說明：獲取紅外傳感器感測距離*/unsigned char GetIR_Distance(unsigned char channle)xdata unsigned in

5、t ucIRDisValue = 0;if(channle<0 | channle>10)return 0;ucIRDisValue = ADC_DistanceGet(channle);ucIRDisValue = (int)SensorDistanceProcess(ucIRDisValue);if(ucIRDisValue>255)ucIRDisValue = 255;return (char)ucIRDisValue;unsigned int GetIRDistance(unsigned char channle)xdata unsigned int ucIRDisV

6、alue = 0;if(channle<0 | channle>10)return 0;ucIRDisValue = ADC_DistanceGet(channle);return ucIRDisValue;/*/! 函數名：unsigned char GetIRCol(unsigned char AD_Point)/! 函數說明：獲取灰度傳感器感測灰度值*/unsigned int GetIRCol(unsigned char ad_channle)xdata unsigned int ucGreyValue;if(ad_channle<0 | ad_channle>

7、9)return 0;ucGreyValue = ADC_DistanceGet(ad_channle);return (ucGreyValue);/*/! 函數名：void ADC_PortInit()/! 函數說明：ADC引腳初始化/!-/! 引腳圖：/!-/! 引腳 端口 AMX0P/!/! AD0-P1.7-0x07/! AD1-P2.0-0x08/! AD2-P2.1-0x09/! AD3-P2.2-0x0A/! AD4-P2.3-0x0B/! AD5-P2.4-0x0C/! AD6-P2.5-0x0D/! AD7-P2.6-0x0E/! AD8-P2.7-0x0F/! AD9-P3

8、.0-0x10*/void ADC_PortInit()unsigned char SFRPAGE_save = SFRPAGE;SFRPAGE = CONFIG_PAGE;/當有語音的時候，P1口不能AD初始化P1MDIN &= 0x80; /P1.7模擬輸入P1SKIP |= 0x80; /交叉開關跳過模擬引腳P2MDIN = 0x00; /P2模擬輸入P2SKIP = 0xFF; /交叉開關跳過模擬引腳/P3MDIN &= 0x01; /P3.0模擬輸入 /P3SKIP |= 0x01; /交叉開關跳過模擬引腳XBR1 = 0x40; /交叉開關使能SFRPAGE = S

9、FRPAGE_save;/*/! 函數名：void ADC_Init()/! 函數說明：ADC初始化*/void ADC_Init()unsigned char SFRPAGE_save = SFRPAGE;ADC_PortInit();SFRPAGE = CONFIG_PAGE;ADC0CN= 0xC0; /跟蹤模式，開啟轉換ADC0CF = (SYSCLOCK/3000000 - 1) << 3;ADC0CF &= 0x04; /右端對齊EIE1 &= 0x08; /禁止ADC中斷/AD0EN = 1;REF0CN = 0x08;SFRPAGE = SFRPAG

10、E_save;/*/! 函數名：unsigned char ADC_DistanceGet(unsigned char AD_port)/! 函數說明：獲取AD_port端口紅外傳感器的值*/unsigned int ADC_DistanceGet(unsigned char AD_port)xdata unsigned char AD_counter=0;xdata unsigned char i = 0;xdata unsigned char adc0_h,adc0_l;xdata unsigned int ad_test;xdata unsigned int ADC_DataStore1

11、0 = 0,0,0,0,0,0,0,0,0,0;if(AD_port>0x0A)return 0xFF;AD_PortSelection(AD_port);ADC_ConvertStart();for(AD_counter=0;AD_counter<10;AD_counter+) while(!AD0INT);adc0_h = ADC0H;adc0_h &= 0x03;adc0_l = ADC0L; ADC_DataStoreAD_counter = (unsigned int)(adc0_h)<<8) + (unsigned int)adc0_l;/ADC_D

12、ataStoreAD_counter = (unsigned int)(adc0_l);AD0INT = 0;ADC_ConvertStart();i+;/ADC_FlagClear(); /ADC_DataStore0 = ADC_AvrDataGet(ADC_DataStore);/return SensorDataAD_port0;ad_test = ADC_AvrDataGet(ADC_DataStore);/ad_test+;/return (ADC_AvrDataGet(ADC_DataStore);return(ad_test);/*/! 函數名：void ADC_Convert

13、Start()/! 函數說明：AD轉換啟動*/void ADC_ConvertStart()unsigned char SFRPAGE_save = SFRPAGE;SFRPAGE = CONFIG_PAGE;AD0EN = 1;/EA = 0;AD0INT = 0;AD0BUSY = 1;SFRPAGE = SFRPAGE_save;/*/! 函數名：void AD_PortSelection(AD_port)/! 函數說明：AD轉換端口配置*/void AD_PortSelection(unsigned char port_unm)unsigned char SFRPAGE_save =

14、SFRPAGE;SFRPAGE = CONFIG_PAGE;switch(port_unm)case 0x01: AMX0P = 0x07; break;case 0x02: AMX0P = 0x08; break;case 0x03: AMX0P = 0x09; break;case 0x04: AMX0P = 0x0A; break;case 0x05: AMX0P = 0x0B; break;case 0x06: AMX0P = 0x0C; break;case 0x07: AMX0P = 0x0D; break;case 0x08: AMX0P = 0x0E; break;case 0

15、x09: AMX0P = 0x0F; break;case 0x0A: AMX0P = 0x10; break;default: break;AMX0N = 0x1F; /負輸入端選擇VDDSFRPAGE = SFRPAGE_save;/*/! 函數名：unsigned int ADC_AvrDataGet(unsigned int *AD_data)/! 函數說明：獲取平均值*/unsigned int ADC_AvrDataGet(unsigned int *AD_data)xdata unsigned int ucAD_avragy,k;xdata unsigned int *uiAD_

16、data = AD_data;xdata unsigned char i,j;xdata unsigned int AD_Array10;for(i=0;i<10;i+)AD_Arrayi = AD_datai;for(i=0;i<10;i+)for(j=0;j<10-i;j+)if(AD_Arrayj>AD_Arrayj+1)k = AD_Arrayj;AD_Arrayj = AD_Arrayj+1;AD_Arrayj+1 = k; ucAD_avragy = AD_Array3 + AD_Array4 + AD_Array5; return ucAD_avragy/3;/*/! 函數名：void ADC0_ISR (void) interrupt 10/! 函數說明：ADC中斷函數*/*void ADC0_ISR (void) interrup