鉸孔切削用量選擇參考表

1、鉸刀鉸削切削用量選擇表高速鋼及硬質合金機鉸刀鉸孔時的進給量mm/r鉸刀直徑鉸刀直徑鉸刀直徑鉸刀直徑鉸刀直徑鉸刀直徑鉸刀直徑刀具材料加工材料<55? 1010?2020 ? 3030 ? 4040 ? 6060 ? 80鋼cb <0.2 ? 0.50.4?0.65?0.8 ? 1.80.95 ?1.3 ? 2.81.5?900MPa0.91.42.13.2鋼Cb >0.15 ?0.35?°.70.55?1.21.2-3.2900MPa0.35高速鋼鉸刀鑄鐵銅及鋁合金HB0.6 ? 1.21.0? 2.01.5?3.02.5-5.03.2-6.4<170鑄鐵HB

2、>0.4 ? 0.80.65?1.31.0?2.01.3-2.61.6-3.22.1- 4.22.6-5.0170未淬硬鋼0.35?°.50.4?0.60.25 ?淬硬鋼0.350.3?0.4硬質合金鉸鑄鐵HB <0.9? 1.41.0?1.51.3-2.02.0-3.0刀170鑄鐵HB >0.7? 1.10.8?1.21.5-3.2170注:1.表內進給量用于加工通孔，加工盲孔時進給量應取為0.2? 0.5mm/r2最大進給量用于在鉆或擴孔之后，精鉸孔之前的粗鉸孔。3?中等進給量用于:1粗鉸之后精鉸H7級精度的孔;2精鏜之后精鉸 H7級精度的孔；3 對硬質合金鉸刀

3、，用于精鉸H8? H9級精度的孔。4最小進給量用于：1拋光或珩磨之前的精鉸孔;2用一把鉸刀鉸 H8? H9級精度的孔；3 對硬質合金鉸刀用于精鉸H7級精度的孔。刀具規格結構鋼、鉻鋼、鎳鉻鋼f(mm/r)(mm)<0.50.60.70.811.21.41.61.822.22.533.54d0=5 ap=0.052421.319.317.6d0=10 ap=0.07521.619.217.415.913.812.3d0=15 ap=0.117.415.314.112.911.19.99.28.27.77.1d0=20 ap=0.12518.216.114.713.511.610.39.38.

4、67.97.4d0=25 ap=0.12516.614.813.412.210.69.48.57.87.26.7d0=30 ap=0.12512.911.29.98.98.27.67.16.66.25.45.14.6dO=4O ap=0.1512.110.49.18.47.57.26.76.25.75.14.74.2d0=50 ap=0.1511.49.98.887.36.76.35.95.44.84.44d0=60 ap=0.210.79.28.27.46.86.35.95.55.14.54.13.7d0=80 ap=0.259.88.57.56.86.25.85.45.14.74.13.8

5、3.4刀具規格灰鑄鐵 190HBf(mm/r)(mm)<0.50.60.70.811.21.41.61.822.5345d0=5 a18.917.215.914.913.312.211.310.69.99.4高速鋼鉸刀粗鉸削的切削速度m/min(粗鉸)p=0.05dO=1O ap=0.07517.916.315.114.112.611.510.79.48.9d0=15 ap=0.115.914.513.412.611.210.39.58.98.48d0=20 ap=0.12516.515.11413.111.710.79.99.28.78.37.46.7d0=25 ap=0.12514.

6、713.412.411.310.49.58.88.27.77.46.66d0=30 ap=0.12512.110.89.89.18.587.66.86.25.44.8dO=4O ap=0.1511.510.39.48.78.17.67.36.55.95.14.6d0=50 ap=0.1511.5109.28.57.97.57.16.35.854.5d0=60 ap=0.210.79.68.78.17.67.16.86.15.54.84.3d0=80 ap=0.25108.98.17.57.16.76.35.65.24.54高速鋼鉸刀鉸削的切削速度m/min 精鉸結構碳鋼、鉻鋼、鎳鉻鋼灰鑄鐵、可鍛