stm8C語言例程

1、文檔可能無法思考全面，請瀏覽后下載! （1）;名稱 ：流水燈;描述 : ；先從上至下點亮所有的LED，再逐個點亮單個LED;*/#include "stm8s105s4.h"#define uchar unsigned char#define uint unsigned intuchar table=0xfe,0xfd,0xfb,0xf7,0xef,0xdf,0xbf,0x7f; /存放點亮單個LED的代碼void DelayMS(uint s) /延時子函數，約延時1ms uint i;for(s;s>0;s-) for(i=0;i<500;i+); void

2、 init(void) /stm8初始化函數PB_DDR = 0xff;PB_CR1 = 0xff; / 將PB設置成推挽輸出PB_CR2 = 0x00;CLK_SWR = 0xE1; /選內部高速時鐘作為主時鐘CLK_CKDIVR = 0x08; /將CPU主頻設置為2M（STM8默認的就是內部高速時鐘的八分頻，即2MH，這里只是告訴大家設置方法）void main()uchar i;init();while (1) /無限循環PB_ODR = 0xff; /先將所有的LED關閉for(i=0;i<9;i+) /一開始是所有的LED熄滅，再逐點亮所有LED，共九種狀態DelayMS(5

3、00); /延時500毫秒PB_ODR<<=1; /將PB_ODR向左移動一位，逐漸點亮所有LED for(i=0;i<8;i+)PB_ODR=tablei; /將table中的數依次賦給PB_ODR ，從上至下依次點亮LEDDelayMS(500); 26 / 26中斷向量：/*BASIC INTERRUPT VECTOR TABLE FOR STM8 devices *Copyright (c) 2007 STMicroelectronics */typedef void far (*interrupt_handler_t)(void);struct interrupt_

4、vector unsigned char interrupt_instruction;interrupt_handler_t interrupt_handler;far interrupt void NonHandledInterrupt (void)/* in order to detect unexpected events during development, it is recommended to set a breakpoint on the following instruction*/return;extern void _stext(); /* startup routin

5、e */struct interrupt_vector const _vectab = 0x82, (interrupt_handler_t)_stext, /* reset */0x82, NonHandledInterrupt, /* trap */0x82, NonHandledInterrupt, /* irq0 */0x82, NonHandledInterrupt, /* irq1 */0x82, NonHandledInterrupt, /* irq2 */0x82, NonHandledInterrupt, /* irq3 */0x82, NonHandledInterrupt

6、, /* irq4 */0x82, NonHandledInterrupt, /* irq5 */0x82, NonHandledInterrupt, /* irq6 */0x82, NonHandledInterrupt, /* irq7 */0x82, NonHandledInterrupt, /* irq8 */0x82, NonHandledInterrupt, /* irq9 */0x82, NonHandledInterrupt, /* irq10 */0x82, NonHandledInterrupt, /* irq11 */0x82, NonHandledInterrupt,

7、/* irq12 */0x82, NonHandledInterrupt, /* irq13 */0x82, NonHandledInterrupt, /* irq14 */0x82, NonHandledInterrupt, /* irq15 */0x82, NonHandledInterrupt, /* irq16 */0x82, NonHandledInterrupt, /* irq17 */0x82, NonHandledInterrupt, /* irq18 */0x82, NonHandledInterrupt, /* irq19 */0x82, NonHandledInterru

8、pt, /* irq20 */0x82, NonHandledInterrupt, /* irq21 */0x82, NonHandledInterrupt, /* irq22 */0x82, NonHandledInterrupt, /* irq23 */0x82, NonHandledInterrupt, /* irq24 */0x82, NonHandledInterrupt, /* irq25 */0x82, NonHandledInterrupt, /* irq26 */0x82, NonHandledInterrupt, /* irq27 */0x82, NonHandledInt

9、errupt, /* irq28 */0x82, NonHandledInterrupt, /* irq29 */;（2）：矩陣鍵盤、數碼管：;描述 : 按下相應按鍵顯示0到F中對應的數;*/#include <stm8s105s4.h>#define uint unsigned int #define uchar unsigned char uchar table=0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,0x88,0x83,0xc6,0xa1,0x86,0x8e;uchar num;void delay(uchar a)

10、uchar i;for(a;a>0;a-) for(i=0;i<255;i+);void init(void)PB_DDR=0XFF; PB_CR1=0XFF; / 將PB設置成推挽輸出 PC_DDR=0X1F; PC_CR1=0XFF; / 將PC設置成推挽輸出 PE_DDR=0x26; PE_CR1=0XFF; /將PE5，PE2，PE1為推挽輸出，其他的設為上拉輸入 PD_DDR=0X80; PD_CR1=0X80; /將PD7設為推挽輸出/*這里的設置比LED的和數碼管的設置要復雜，開始引入輸入 模式，矩陣鍵盤列為輸出，行為輸入，請參考協會開發板原理圖及STM8轉51PDF

11、資料*/*掃描方式也可為行輸出，列輸入，讀者可以自己嘗試著修改*/uchar keys(void) /此子函數看起來很長，實則只有前面一截內容，下面的“同理可得”uchar temp;PE_ODR=0X26; /將列中的PD7置為低電平，列中的其他三個置為高電平PD_ODR=0x00;delay(40); /這里要說明一下，由于矩陣鍵盤第一列和AD鍵盤共用一個IO口/AD鍵盤的RC會影響IO口電平變化的時間，這里需要延時一段時間,讓電容C放電完畢if(PE_IDR&0x40)=0) /如果第一列的第四行按鍵被按下，則進入if語句內 delay(5); /延時一段時間，等待IO口電平穩定

12、，即消抖if(PE_IDR&0x40)=0) /再次判斷按鍵是否被按下，避免干擾 num=12; /如果第一列的第四行按鍵被按下,則令num=12,即數碼管顯示 為C while(PE_IDR&0x40)=0); /如果按鍵沒有松開，則等待 temp=PC_IDR&0xe0; if(temp!=0xe0) delay(5); temp=PC_IDR&0xe0; if(temp!=0xe0) switch(temp) case 0xc0:num=0; /如果temp的值為0xc0，則說明第1個按鍵被按下，下面的依次類推break; case 0xa0:num=4;

13、break; case 0x60:num=8;break; while(PC_IDR&0xe0)!=0xe0); PE_ODR=0X24;PD_ODR=0x80;if(PE_IDR&0x40)=0) num=13;delay(5);while(PE_IDR&0x40)=0); temp=PC_IDR&0xe0;if(temp!=0xe0) delay(5); temp=PC_IDR&0xe0; if(temp!=0xe0) switch(temp) case 0xc0:num=1;break; case 0xa0:num=5;break; case 0x

14、60:num=9;break; while(PC_IDR&0xe0)!=0xe0); PE_ODR=0X22;PD_ODR=0x80;if(PE_IDR&0x40)=0) num=14;delay(5);while(PE_IDR&0x40)=0); temp=PC_IDR&0xe0;if(temp!=0xe0) delay(5); temp=PC_IDR&0xe0; if(temp!=0xe0) switch(temp) case 0xc0:num=2;break; case 0xa0:num=6;break; case 0x60:num=10;brea

15、k; while(PC_IDR&0xe0)!=0xe0); PE_ODR=0X06;PD_ODR=0x80;if(PE_IDR&0x40)=0) num=15;delay(5);while(PE_IDR&0x40)=0); temp=PC_IDR&0xe0;if(temp!=0xe0) delay(5); temp=PC_IDR&0xe0; if(temp!=0xe0) switch(temp) case 0xc0:num=3;break; case 0xa0:num=7;break; case 0x60:num=11;break; while(PC_I

16、DR&0xe0)!=0xe0); return num; void main()uchar n;init();while(1) n=keys(); /把函數keys()的返回值num賦給nPB_ODR=tablen; PC_ODR|=0x00; /選擇第一個數碼管中斷向量：/*BASIC INTERRUPT VECTOR TABLE FOR STM8 devices *Copyright (c) 2007 STMicroelectronics */typedef void far (*interrupt_handler_t)(void);struct interrupt_vector

17、unsigned char interrupt_instruction;interrupt_handler_t interrupt_handler;far interrupt void NonHandledInterrupt (void)/* in order to detect unexpected events during development, it is recommended to set a breakpoint on the following instruction*/return;extern void _stext(); /* startup routine */str

18、uct interrupt_vector const _vectab = 0x82, (interrupt_handler_t)_stext, /* reset */0x82, NonHandledInterrupt, /* trap */0x82, NonHandledInterrupt, /* irq0 */0x82, NonHandledInterrupt, /* irq1 */0x82, NonHandledInterrupt, /* irq2 */0x82, NonHandledInterrupt, /* irq3 */0x82, NonHandledInterrupt, /* ir

19、q4 */0x82, NonHandledInterrupt, /* irq5 */0x82, NonHandledInterrupt, /* irq6 */0x82, NonHandledInterrupt, /* irq7 */0x82, NonHandledInterrupt, /* irq8 */0x82, NonHandledInterrupt, /* irq9 */0x82, NonHandledInterrupt, /* irq10 */0x82, NonHandledInterrupt, /* irq11 */0x82, NonHandledInterrupt, /* irq1

20、2 */0x82, NonHandledInterrupt, /* irq13 */0x82, NonHandledInterrupt, /* irq14 */0x82, NonHandledInterrupt, /* irq15 */0x82, NonHandledInterrupt, /* irq16 */0x82, NonHandledInterrupt, /* irq17 */0x82, NonHandledInterrupt, /* irq18 */0x82, NonHandledInterrupt, /* irq19 */0x82, NonHandledInterrupt, /*

21、irq20 */0x82, NonHandledInterrupt, /* irq21 */0x82, NonHandledInterrupt, /* irq22 */0x82, NonHandledInterrupt, /* irq23 */0x82, NonHandledInterrupt, /* irq24 */0x82, NonHandledInterrupt, /* irq25 */0x82, NonHandledInterrupt, /* irq26 */0x82, NonHandledInterrupt, /* irq27 */0x82, NonHandledInterrupt,

22、 /* irq28 */0x82, NonHandledInterrupt, /* irq29 */;（3）;名稱 :定時器的使用 ;描述 : 數碼管顯示0F，利用定時器使得1秒變換一次;*/#include <stm8s105s4.h>#define uint unsigned int #define uchar unsigned char uchar table=0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,0x88,0x83,0xc6,0xa1,0x86,0x8e;uchar t;void init(void) PB_DD

23、R=0XFF; PB_CR1=0XFF; PB_CR2=0X00; PC_DDR=0XFF; PC_CR1=0XFF; PC_CR2=0X00; TIM2_EGR=0X01; /允許產生更新事件 TIM2_PSCR=0X01; /分頻，使頻率為1MHz TIM2_ARRH=0XC3; /更新后計數器的值 TIM2_ARRL=0X50; TIM2_CR1=0X05; /允許定時器工作 TIM2_IER=0X01; /允許更新中斷 _asm("rim"); /匯編語句，啟動定時器 /注意！使用定時器時要定義中斷函數入口，詳請打開main.c下面的stm8_interrupt_v

24、ector.c，請按照注釋進行修改 void main(void) uchar i=0,j; init(); while(1) PB_ODR=tablei; PC_ODR=0x02; /選擇第二個數碼管顯示 if(t=20) /這里設置50ms進入一次中斷，t=20剛好為1秒 t=0; /t清零 i+; if(i=16) i=0; /由于數組中只有16個數，所以i最大只能為15，否則顯示會出現亂碼現象 far interrupt void TIM2_UP_IRQHandler (void) /中斷函數 TIM2_SR1 = 0x00; /進入中斷時TIM2_SR1最低位會被硬件自動置一，進入中

25、斷后必須將其清零，否則無法再次產生中斷 t+; /進入中斷后t自加1/* BASIC INTERRUPT VECTOR TABLE FOR STM8 devices * Copyright (c) 2007 STMicroelectronics */typedef void far (*interrupt_handler_t)(void);struct interrupt_vector unsigned char interrupt_instruction; interrupt_handler_t interrupt_handler;far interrupt void NonHandledI

26、nterrupt (void) /* in order to detect unexpected events during development, it is recommended to set a breakpoint on the following instruction */ return;extern void _stext(); /* startup routine */extern far interrupt void TIM2_UP_IRQHandler (void); /使用定時器要加上這句話struct interrupt_vector const _vectab =

27、 0x82, (interrupt_handler_t)_stext, /* reset */ 0x82, NonHandledInterrupt, /* trap */ 0x82, NonHandledInterrupt, /* irq0 */ 0x82, NonHandledInterrupt, /* irq1 */ 0x82, NonHandledInterrupt, /* irq2 */ 0x82, NonHandledInterrupt, /* irq3 */ 0x82, NonHandledInterrupt, /* irq4 */ 0x82, NonHandledInterrup

28、t, /* irq5 */ 0x82, NonHandledInterrupt, /* irq6 */ 0x82, NonHandledInterrupt, /* irq7 */ 0x82, NonHandledInterrupt, /* irq8 */ 0x82, NonHandledInterrupt, /* irq9 */ 0x82, NonHandledInterrupt, /* irq10 */ 0x82, NonHandledInterrupt, /* irq11 */ 0x82, NonHandledInterrupt, /* irq12 */ 0x82, TIM2_UP_IRQ

29、Handler, /* irq13 */ /使用定時器要把這里的“NonHandledInterrupt”改為“TIM2_UP_IRQHandler”，即中斷函數名 0x82, NonHandledInterrupt, /* irq14 */ 0x82, NonHandledInterrupt, /* irq15 */ 0x82, NonHandledInterrupt, /* irq16 */ 0x82, NonHandledInterrupt, /* irq17 */ 0x82, NonHandledInterrupt, /* irq18 */ 0x82, NonHandledInterr

30、upt, /* irq19 */ 0x82, NonHandledInterrupt, /* irq20 */ 0x82, NonHandledInterrupt, /* irq21 */ 0x82, NonHandledInterrupt, /* irq22 */ 0x82, NonHandledInterrupt, /* irq23 */ 0x82, NonHandledInterrupt, /* irq24 */ 0x82, NonHandledInterrupt, /* irq25 */ 0x82, NonHandledInterrupt, /* irq26 */ 0x82, NonH

31、andledInterrupt, /* irq27 */ 0x82, NonHandledInterrupt, /* irq28 */ 0x82, NonHandledInterrupt, /* irq29 */;（3） （4）：蜂鳴器：定時器方式;名稱 :蜂鳴器 ;描述 : 利用定時器產生;*/#include <stm8s105s4.h>#define uchar unsigned char _Bool beep PD_ODR:4;uchar t2,t3;void init(void)PD_DDR=0X10;PD_CR1=0X10; /連接蜂鳴器的IO口初始化PD_CR2=0X

32、00;PD_ODR|=0x10;TIM2_EGR=0X01; /允許產生更新事件TIM2_PSCR=0X01; /分頻，使頻率為1MHzTIM2_ARRH=0XC3; /更新后計數器的值TIM2_ARRL=0X50; /定時50ms，用于控制發聲時間TIM2_CR1=0X05; /允許定時器工作TIM2_IER=0X01; /允許更新中斷TIM3_EGR=0X01; /允許產生更新事件TIM3_PSCR=0X01; /分頻，使頻率為1MHzTIM3_ARRH=0X00; /更新后計數器的值TIM3_ARRL=0Xfa; /這里定時0.25ms，用于產生所需的頻率TIM3_CR1=0X05; /

33、允許定時器工作TIM3_IER=0X01; /允許更新中斷_asm("rim"); /匯編語句，啟動定時器void delay(uchar s)uchar i;for(s;s>0;s-) for(i=0;i<250;i+);void main()init();while(1) if(t3%2=0) /前一秒產生2KHz頻率的聲音 beep=1; /定時器3時間0.25ms，一個周期0.5ms，故頻率為2Kelse beep=0;while(t2>=20&&t2<40) /第二秒產生1KHz頻率聲音 if(t3%4<2) beep

34、=1; else beep=0;while(t2>=40&&t2<60) /第三秒產生500Hz頻率聲音 if(t3%8<4) beep=1; elsebeep=0;if(t2>=60) t2=0; if(t3=8) t3=0;far interrupt void TIM2_UP_IRQHandler (void) /定時器2中斷函數 TIM2_SR1 = 0x00; /清零TIM2_SR1 t2+;far interrupt void TIM3_UP_IRQHandler (void) /定時器三中斷函數 TIM3_SR1 = 0x00; /清零TIM

35、2_SR1 t3+;中斷向量：/*BASIC INTERRUPT VECTOR TABLE FOR STM8 devices *Copyright (c) 2007 STMicroelectronics */typedef void far (*interrupt_handler_t)(void);struct interrupt_vector unsigned char interrupt_instruction;interrupt_handler_t interrupt_handler;far interrupt void NonHandledInterrupt (void)/* in o

36、rder to detect unexpected events during development, it is recommended to set a breakpoint on the following instruction*/return;extern void _stext(); /* startup routine */extern far interrupt void TIM2_UP_IRQHandler (void);extern far interrupt void TIM3_UP_IRQHandler (void);struct interrupt_vector c

37、onst _vectab = 0x82, (interrupt_handler_t)_stext, /* reset */0x82, NonHandledInterrupt, /* trap */0x82, NonHandledInterrupt, /* irq0 */0x82, NonHandledInterrupt, /* irq1 */0x82, NonHandledInterrupt, /* irq2 */0x82, NonHandledInterrupt, /* irq3 */0x82, NonHandledInterrupt, /* irq4 */0x82, NonHandledI

38、nterrupt, /* irq5 */0x82, NonHandledInterrupt, /* irq6 */0x82, NonHandledInterrupt, /* irq7 */0x82, NonHandledInterrupt, /* irq8 */0x82, NonHandledInterrupt, /* irq9 */0x82, NonHandledInterrupt, /* irq10 */0x82, NonHandledInterrupt, /* irq11 */0x82, NonHandledInterrupt, /* irq12 */0x82, TIM2_UP_IRQH

39、andler, /* irq13 */0x82, NonHandledInterrupt, /* irq14 */0x82, TIM3_UP_IRQHandler, /* irq15 */0x82, NonHandledInterrupt, /* irq16 */0x82, NonHandledInterrupt, /* irq17 */0x82, NonHandledInterrupt, /* irq18 */0x82, NonHandledInterrupt, /* irq19 */0x82, NonHandledInterrupt, /* irq20 */0x82, NonHandled

40、Interrupt, /* irq21 */0x82, NonHandledInterrupt, /* irq22 */0x82, NonHandledInterrupt, /* irq23 */0x82, NonHandledInterrupt, /* irq24 */0x82, NonHandledInterrupt, /* irq25 */0x82, NonHandledInterrupt, /* irq26 */0x82, NonHandledInterrupt, /* irq27 */0x82, NonHandledInterrupt, /* irq28 */0x82, NonHan

41、dledInterrupt, /* irq29 */;（5） 蜂鳴器：stm8BEEP方式;名稱 ：STM8自帶蜂鳴器使用;描述 : ；注！此功能需用ST Link輔助設置，協會實驗板無法正常工作，這里僅作參考;*/#include <stm8s105s4.h>#define uchar unsigned charuchar t;void init(void) /初始化函數 CLK_ICKR|=0x08; / 打開芯片內部的低速振蕩器LSI while(CLK_ICKR&0x10)=0); / 等待振蕩器穩定 TIM2_EGR=0X01; /允許產生更新事件 TIM2_PS

42、CR=0X01; /分頻，使頻率為1MHz TIM2_ARRH=0XC3; /更新后計數器的值 TIM2_ARRL=0X50; TIM2_CR1=0X05; /允許定時器工作 TIM2_IER=0X01; /允許更新中斷 _asm("rim"); /匯編語句，啟動定時器void main() uchar i; init(); while(1) BEEP_CSR=0x26; /一秒2KHz while(t>=20)&&(t<40) BEEP_CSR=0x2e; /一秒1KHz while(t>=40)&&(t<60) B

43、EEP_CSR=0x3e; /一秒500Hz while(t>=60)&&(t<80) BEEP_CSR&=0xdf; /一秒關閉 if(t>=80) t=0; far interrupt void TIM2_UP_IRQHandler (void) /中斷函數 TIM2_SR1 = 0x00; t+;中斷向量：/*BASIC INTERRUPT VECTOR TABLE FOR STM8 devices *Copyright (c) 2007 STMicroelectronics */typedef void far (*interrupt_hand

44、ler_t)(void);struct interrupt_vector unsigned char interrupt_instruction;interrupt_handler_t interrupt_handler;far interrupt void NonHandledInterrupt (void)/* in order to detect unexpected events during development, it is recommended to set a breakpoint on the following instruction*/return;extern vo

45、id _stext(); /* startup routine */extern far interrupt void TIM2_UP_IRQHandler (void);struct interrupt_vector const _vectab = 0x82, (interrupt_handler_t)_stext, /* reset */0x82, NonHandledInterrupt, /* trap */0x82, NonHandledInterrupt, /* irq0 */0x82, NonHandledInterrupt, /* irq1 */0x82, NonHandledI

46、nterrupt, /* irq2 */0x82, NonHandledInterrupt, /* irq3 */0x82, NonHandledInterrupt, /* irq4 */0x82, NonHandledInterrupt, /* irq5 */0x82, NonHandledInterrupt, /* irq6 */0x82, NonHandledInterrupt, /* irq7 */0x82, NonHandledInterrupt, /* irq8 */0x82, NonHandledInterrupt, /* irq9 */0x82, NonHandledInterrupt, /* irq10 */0x82, NonHandledInterrupt, /* irq11 */0x82, NonHandledInterrupt, /* irq12 */0x82, TIM2_UP_IRQHandler, /* irq13 */0x82, NonHandledInterr