MSP430單片機試驗報告

1、MSP430單片機實驗報告專業:姓名：學號：MSP430單片機實驗報告設計目標：使8位數碼管顯示“ 5202114. ,深入了解串行數據接口.實現過程：主要分為主函數、驅動 8位數碼管函數、驅動 1位數碼管函數及延時函數.延時函數：采用for循環.驅動1位數碼管子函數：設置74HC164的時鐘傳輸和數傳輸, 聲明變量,使數據表中每一個要表 示的字符的每一位都與 shift做與運算從而進行傳輸,上升沿將傳輸數據傳送出去.驅動 1位數碼管子函數的流程圖如圖 1所示.設置時鐘和 數據傳輸for循環逐個發送8位圖1驅動1位數碼管子函數流程圖驅動8位數碼管子函數：調用 8次驅動1位數碼管子函數.驅動 8

2、位數碼管子函數流程圖如圖 2所示.調用8次一 位數碼管圖2驅動8位數碼管流程圖主函數：設置IO 口,while死循環中調用驅動 8位.主函數流程圖如圖3所示.可編輯while圖3主函數流程圖實驗結果：供電后,數碼管顯示“ 5202114. 字樣./*源程序:程序名稱：5202114.*/*程序功能:通過模擬同步串口限制8個共陽數碼管*/*P5.1數據管腳,P5.3同步時鐘管腳*/頭文件/聲明驅動1位數碼管函數#include void delay(void);/聲明延遲函數void seg7_1 (unsigned char seg7_data);void seg7_8 ( unsigned

3、char seg7_data7,unsigned char seg7_data6,unsigned char seg7_data5,unsigned char seg7_data4,unsigned char seg7_data3,unsigned char seg7_data2,unsigned char seg7_data0);const unsigned char decoder_seg7=0x92,0xa4,0xc0,0xf9,0xb0,0xf9,0x99,0x7f ;int main(void)WDTCTL=WDTPW+WDTHOLD;P5SEL&=BIT1;P5DIR|=BIT1;

4、P5SEL&=BIT3;P5DIR|=BIT3;while(1)seg7_8 (7,6,5,4,3,2,1,0);delay ( );void seg7_8 (unsigned char seg7_data7,unsigned char seg7_data6,unsigned char seg7_data5,unsigned char seg7_data4,/聲明驅動8位數碼管函數/數碼管顯示表【5202114./主函數/關閉看門狗/設置P5.1端口為并行數字輸入/輸出口/設置P5.1端口為輸出口/設置P5.3端口為并行數字輸入/輸出口/設置P5.3端口為輸出口/重復執行/調用驅動8位數碼管函

5、數/延時unsigned char seg7_data3,unsigned char seg7_data1, unsigned char seg7_data0)/驅動8位數碼管的同步串行數據接口驅動函數seg7_1(seg7_data0);/調用1位數碼管的同步串行數據接口驅動函數seg7_1(seg7_data1);seg7_1(seg7_data2);seg7_1(seg7_data3);seg7_1(seg7_data4);seg7_1(seg7_data5);seg7_1(seg7_data6);seg7_1(seg7_data7);void seg7_1 (unsigned char seg7_data)/驅動1位數碼管的同步串行數據接口驅動函數unsigned char code_seg7;/聲明顯示代碼變量unsigned char a;/聲明循環變量unsigned char shift;/聲明串行數據位存儲變量code_seg7=decoder_seg7seg7_data;/顯示數據譯碼/同步串行接口初始化P5OUT&=BIT1;P5OUT&=BIT3;shift=0x80;for(a=0; a1;void delay (void)/(/ P5.1 輸出低電平/ P5.3 輸出低電平/串行數據位指向8位數據的最高位/判斷顯示代碼位的狀態/ P