怎樣讓Cisco2950交換接恢復到出廠設置.doc

1、關閉交換機2、按住面板前MODE按鈕不放，加電。進入switch：3、flash_init4、load_helper5、dir flash：6、delete flash:config.text7、delete flash:vlan.dat8、重啟switch: flash_initInitializing Flash.The flash is already initialized.switch: load_helperswitch: dir flash:Directory of flash:/2 -rwx 1674921 c2950-c3h2s-mz.120-5.3.WC.1.bin4 drwx 10240 html165 -rwx 1559 config.text166 -rwx 269 env_vars4778496 bytes available (2962944 bytes used)switch: delete flash:config.textAre you sure you want to delete flash:config.text (y/n)?yFile flash:config.text deletedswitch: ? - Present list of available commandsboot - Load and boot an executable imagecat - Concatenate (type) file(s)copy - Copy a filedelete - Delete file(s)dir - List files in directoriesflash_init - Initialize flash filesystem(s)format - Format a filesystemfsck - Check filesystem consistencyhelp - Present list of available commandsload_helper - Load and initialize a helper imagememory - Present memory heap utilization informationmkdir - Create dir(s)more - Concatenate (display) file(s)rename - Rename a filereset - Reset the systemrmdir - Delete empty dir(s)set - Set or display environment variablesset_param - Set system parameters in flashtrap - Cause a software breakpoint to occurtype - Concatenate (type) file(s)unset - Unset one or more environment variablesversion - Display boot loader versionswitch:switch: bootLoading flash:c2950-c3h2s-mz.120-5.3.WC.1.bin.#File flash:c2950-c3h2s-mz.120-5.3.WC.1.bin uncompressed and installed, entry point: 0x80010000executing.Restricted Rights LegendUse, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013.cisco Systems, Inc.170 West Tasman DriveSan Jose, California 95134-1706Cisco Internetwork Operating System SoftwareIOS (tm) C2950 Software (C2950-C3H2S-M), Version 12.0(5.3)WC(1), MAINTENANCE INTERIM SOFTWARECopyright (c) 1986-2001 by cisco Systems, Inc.Compiled Mon 30-Apr-01 07:56 by devgoyalImage text-base: 0x80010000, data-base: 0x8031A000Initializing flashfs.flashfs1: 161 files, 3 directoriesflashfs1: 0 orphaned files, 0 orphaned directoriesflashfs1: Total bytes: 7741440flashfs1: Bytes used: 2960896flashfs1: Bytes available: 4780544flashfs1: flashfs fsck took 6 seconds.flashfs1: Initialization complete.Done initializing flashfs.C2950 POST: System Board Test : PassedC2950 POST: Ethernet Controller Test : PassedC2950 POST: MII TEST : Passedcisco WS-C2950-24 (RC32300) processor (revision B0) with 22260K bytes of memory.Processor board ID FOC0605W1QVLast reset from system-resetProcessor is running Enterprise Edition SoftwareCluster command switch capableCluster member switch capable24 FastEthernet/IEEE 802.3 interface(s)32K bytes of flash-simulated non-volatile configuration memory.Base ethernet MAC Address: 00:08:E3:68:76:00Motherboard assembly number: 73-5781-08Power supply part number: 34-0965-01Motherboard serial number: FOC060509VFPower supply serial number: DAB05523DPLModel revision number: B0Motherboard revision number: B0Model number: WS-C2950-24System serial number: FOC0605W1QVC2950 INIT: Complete00:00:17: %SYS-5-RESTART: System restarted -Cisco Internetwork Operating System SoftwareIOS (tm) C2950 Software (C2950-C3H2S-M), Version 12.0(5.3)WC(1), MAINTENANCE INTERIM SOFTWARECopyright (c) 1986-2001 by cisco Systems, Inc.Compiled Mon 30-Apr-01 07:56 by devgoyal- System Configuration Dialog -At any point you may enter a question mark ? for help.Use ctrl-c to abort configuration dialog at any prompt.Default settings are in square brackets .Continue with configuration dialog? yes/no: yEnter IP address: 0Enter IP netmask: Would you like to enter a default gateway address? yes: nEnter host name Switch: 2950-2The enable secret is a one-way cryptographic secret usedinstead of the enable password when it exists.Enter enable secret: Would you like to configure a Telnet password? yes: yEnter Telnet password: Would you like to enable as a cluster command switch? yes/no: nThe following configuration command script was created:ip subnet-zerointerface VLAN1ip address 0 hostname 2950-2enable secret 5 $1$5Ocj$1osGcBmYqsrb0BbHHI4Lr/line vty 0