食品機械加工工藝課程畢業設計外文文獻翻譯/中英文翻譯/外文翻譯

中國地質大學長城學院  本科畢業設計外文資料翻譯  系     別：  工程技術系  專     業：  機械設計制造及其自動化  姓     名：  李旭            學     號：  05211503      2015年   3  月   5  日  Introduction of Machining Have a shape as a processing method, all machining process for the production of the most commonly used and most important method. Machining process is a process generated shape, in this process, Drivers device on the work piece material to be in the form of chip removal. Although in some occasions, the workpiece under no circumstances, the use of mobile equipment to the processing, However, the majority of the machining is not only supporting the workpiece also supporting tools and equipment to complete. Machining know the process has two aspects. Small group of low-cost production. For casting, forging and machining pressure, every production of a specific shape of the workpiece, even a spare parts, almost have to spend the high cost of processing. Welding to rely on the shape of the structure, to a large extent, depend on effective in the form of raw materials. In general, through the use of expensive equipment and without special processing conditions, can be almost any type of raw materials, mechanical processing to convert the raw materials processed into the arbitrary shape of the structure, as long as the external dimensions large enough, it is possible. Because of a production of spare parts, even when the parts and structure of the production batch sizes are suitable for the original casting, Forging or pressure processing to produce, but usually prefer machining. Strict precision and good surface finish, machining the second purpose is the establishment of the high precision and surface finish possible on the basis of. Many parts, if any other means of production belonging to the large-scale production, Well Machining is a low-tolerance and can meet the requirements of small batch production. Besides, many parts on the production and processing of coarse process to improve its general shape of the surface. It is only necessary precision and choose only the surface machining. For instance, thread, in addition to mechanical processing, almost no other processing method for processing. Another example is the blacksmith pieces keyhole processing, as well as training to be conducted immediately after the mechanical completion of the processing. Primary Cutting Parameters Cutting the work piece and tool based on the basic relationship between the following four elements to fully describe : the tool geometry, cutting speed, feed rate, depth and penetration of a cutting tool. Cutting Tools must be of a suitable material to manufacture, it must be strong, tough, hard and wear-resistant. Tool geometry - to the tip plane and cutter angle characteristics - for each cutting process must be correct.   Cutting speed is the cutting edge of work piece surface rate, it is inches per minute to show. In order to effectively processing, and cutting speed must adapt to the level of specific parts - with knives. Generally, the more hard work piece material, the lower the rate. Progressive Tool to speed is cut into the work piece speed. If the work piece or tool for rotating movement, feed rate per round over the number of inches to the measurement. When the work piece or tool for reciprocating movement and feed rate on each trip through the measurement of inches. Generally, in other conditions, feed rate and cutting speed is inversely proportional to. Depth of penetration of a cutting tool - to inches dollars - is the tool to the work piece distance. Rotary cutting it to the chip or equal to the width of the linear cutting chip thickness. Rough than finishing, deeper penetration of a cutting tool depth. Rough machining and finishing machining There are two kinds of cuts in machine- shop work called, respectively, the "roughing cut" and the "finishing cut". When a piece is "roughed out", it is quite near the shape and size required, but enough metal has been left on the surface to finish smooth and to exact size." Generally speaking, bars of steel, forging, castings, etc. are machined to the required shape and size with only one roughing and one finishing cut. Sometimes, however, certain portions of a piece may require more than one roughing cut. Also, in some jobs, for example, when great accuracy is not needed, or when a comparatively small amount of metal must be removed, a finishing cut may be all that is required. The roughing cut, to remove the greater part of the excess material, should be reasonably heavy, that is, all the machine, or cutting tool, or work, or all three, will stand. So the machinist s purpose is to remove the excess stock as fast as he can without leaving, at the same time, a surface too torn and rough, without bending the piece if it is slender, and without spoiling the centers. The finishing cut, to make the work smooth and accurate, is a finer cut. The emphasis here is refinement - very sharp tool, comparatively little metal removed, and a higher degree of accuracy in measurement. Whether roughing or finishing, the machinist must set the machine for the given job. He must consider the size and shape of the work and the kind of material, also the kind of tool used and the nature of the cut to be made, then he proceeds to set the machine for the correct speed and feed and to set the tool to take the depth of cut desired. Automatic Fixture Design Assembly equipment used in the traditional synchronous fixture put parts of the fixture mobile center, to ensure that components from transmission from the plane or equipment plate placed after removal has been scheduled for position. However, in certain applications, mobile mandatory parts of the center line, it may cause parts or equipment damage. When parts vulnerability and may lead to a small vibration abandoned, or when their location is by machine spindle or specific to die, Tolerance again or when the request is a sophisticated, it would rather let the fixture to adapt to the location of parts, and not the contrary. For these tasks, Elyria, Ohio, the company has developed Zaytran a general non-functional data synchronization West category FLEXIBILITY fixture. Fixture because of the interaction and synchronization devices is independent; the synchronous device can use sophisticated equipment to replace the slip without affecting the fixture force. Fixture specification range from 0.2 inches itinerary, 5 pounds clamping force of the six-inch trip, 400-inch clamping force. The characteristics of modern production are becoming smaller and smaller quantities and product specifications biggest changes. Therefore, in the final stages of production, assembly of production, quantity and product design changes appear to be particularly vulnerable. This situation is forcing many companies to make greater efforts to rationalize the extensive reform and the previously mentioned case of assembly automation. Despite flexible fixture behind the rapid development of flexible transport and handling devices, such as backward in the development of industrial robots, it is still expected to increase the flexibility fixture. In fact the important fixture devices - the production of the devices to strengthen investment on the fixture so that more flexibility in economic support holders. According to their flexibility and fixture can be divided into: special fixture, the fixture combinations, the standard fixture, high flexible fixture. Flexible fixture on different parts of their high adaptability and the few low-cost replacement for the characteristic. Forms can transform the structure of the flexible fixture can be installed with the change of structure components (such as needle cheek plate, Multi-chip components and flake cheek plate), a non-standard work piece gripper or clamping elements (for example: commencement standard with a clamping fixture and mobile components fixture supporting documents), or with ceramic or hardening of the intermediary substances (such as : Mobile particle bed fixture and heat fixture tight fixture). To production, the parts were secured fixture, the need to generate clamping function, its fixture with a few unrelated to the sexual submissive steps. According to the processing was part of that foundation and working characteristics to determine the work piece fixture in the required position, then need to select some stability flat combination, These constitute a stable plane was fixed in the work piece fixture set position on the clamp-profile structure, all balanced and torque, it has also ensured that the work features close to the work piece. Finally, it must be calculated and adjusted, assembly or disassembly be standard fixture components required for the position, so that the work piece firmly by clamping fixture in China. In accordance with this procedure, the outline fixture structure and equipped with the planning and recording process can be automated control. Structural modeling task is to produce some stable flat combination, Thus, these plane of the work pieces clamping force and will fixture stability. According to usual practice, this task can be human-machine dialogue that is almost completely automated way to completion. A man-machine dialogue that is automated fixture structure modeling to determine the merits can be conducted in an organized and planning fixture design reduce the amount of the design, shortening the study period and better distribution of work conditions. In short, can be successfully achieved significantly improve fixture efficiency and effectiveness. Fully prepared to structure programs and the number of material circumstances, the completion of the first successful assembly can save up to 60% of the time. Therefore fixture process modeling agencies is the purpose of the program has appropriate documents. 中文翻譯  食品機械加工工藝  機械加工是所有制造過程中最普遍使用的而且是最重要的方法。機械加工過程是一個產生形狀的過程，在這過 程中，驅動裝置使工件上的一些材料以切屑的形式被去除。盡管在某些場合，工件無承受情況下，使用移動式裝備來實現加工，但大多數的機械加工是通過既支承工件又支承刀具的裝備來完成。  機械加工過程中具備兩方面。小批生產低費用。對于鑄造、鍛造和壓力加工，每一個要生產的具體工件形狀，即使是一個零件，幾乎都要花費高額的加工費用。靠焊接來產生的結構形狀，在很大程度上取決于有效的原材料的形式。一般來說，通過利用貴重設備而又無需特種加工條件下，幾乎可以以任何種類原材料開始，借助機械加工把原材料加工成任意所需要的結構形狀，只要外 部尺寸足夠大，那都是可能的。因此對于生產一個零件，甚至當零件結構及要生產的批量大小上按原來都適于用鑄造、鍛造或者壓力加工來生產的，但通常寧可選擇機械加工。  嚴密的精度和良好的表面粗糙度，機械加工的第二方面用途是建立在高精度和可能的表面粗糙度基礎上。許多零件，如果用別的其他方法來生產屬于大批量生產的話，那么在機械加工中則是屬于低公差且又能滿足要求的小批量生產了。另一方面，許多零件靠比較粗糙的生產加工工藝制造其表面形狀，而僅僅是在需要高精度的且選擇過的表面才進行機械加工。例如內螺紋，除了機械加工之外，幾乎沒 有別的加工方法能進行加工。又如已鍛工件上的小孔加工，也是被鍛后緊接著進行機械加工才完成的。  基本的機械加工參數  切削中工件與刀具的基本關系是以以下四個要素來充分描述的：刀具的幾何形狀，切削速度，進給速度，和背吃刀量。  切削刀具必須用一種合適的材料來制造，它必須是強固、韌性好、堅硬而且耐磨的。刀具的幾何形狀 以刀尖平面和刀具角為特征 對于每一種切削工藝都必須是正確的。  切削速度是切削刃通過工件表面的速率，它是以每分鐘英寸來表示。為了有效地加工，切削速度高低必須適應特定的工件 刀具配合。一般來 說，工件材料越硬，速度越低。  進給速度是刀具切進工件的速度。若工件或刀具作旋轉運動，進給量是以每轉轉過的英寸數目來度量的。當?shù)毒呋蚬ぜ魍鶑瓦\動時，進給量是以每一行程走過的英寸數度量的。一般來說，在其他條件相同時，進給量與切削速度成反比。  背吃刀量 以英寸計 是刀具進入工件的距離。它等于旋削中的切屑寬度或者等于線性切削中的切屑的厚度。粗加工比起精加工，背吃刀量更大。  粗切削與精切削  工廠的切削加工有兩種，分別稱為“粗切削”和“精切削”。工件經“粗切削”后，十分接近所要求的形狀和尺寸，但加工表 面仍留有足夠的金屬余量，以供精加工，使工件表面粗糙、尺寸準確。一般地說，鋼質棒料、鍛件、鑄件等只經一次粗切削和一次精切削即可達到所要求的形狀和尺寸。不過，有時工件的某些部位可能需要不止一次的粗切削。有些加工，如精度要求不高或需要切除的金屬量較小，也可能只需一次精切削。粗切削因為要去除大部分的余料，切削力量肯定是相當大的，這就意味著，整個機器、刀具、工件或這三者都要能承受得了。機加工工人的目的是盡可能快地切除余料，而留下的加工表面又不能太粗糙，細長的工件不能抗彎，也不能損壞頂尖。精切削是使工件表面光滑、尺寸準 確，因而是一種更精細的切削。精加工強調的是精度 使用非常鋒利的刀具，切除的金屬量較少，測量時的精密度要求較高。無論是粗切削還是精切削，機加工工人都必須按給定的工作來調好機床，必須考慮工件的大小和形狀，材料的種類，刀具的種