模具英語3.doc

機械建材模具英語專業術語大全 機械建材模具英語專業術語大全 一： 模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 回針碰料位：return pin and cavity interference 模總高超出啤機規格：mold base shut hight 頂針碰運水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 邊釘/導邊：leader pin/guide pin 邊司/導套：bushing/guide bushing 中托司：shoulder guide bushing 不準用鑲件： Do not use (core/cavity) insert 用鈹銅做鑲件： use beryllium copper insert 初步（正式）模圖設計：preliinary (final) mold design 反呵：reverse core 彈弓壓縮量：spring compressed length 穩定性好：good stability,stable 強度不夠：insufficient rigidity 均勻冷卻：even cooling 扣模：sticking 熱膨脹：thero expansion 公差：tolorance 銅公(電極）：copper electrode 中托邊L：guide pin 頂針板：ejector retainner plate 托板：support plate 螺絲： screw 管釘：dowel pin 開模槽：ply bar scot 內模管位：core/cavity inter-lock 頂針：ejector pin 司筒：ejector sleeve 司筒針：ejector pin 推板：stripper plate 縮呵：movable core,return core core puller 扣機（尼龍拉勾）：nylon latch lock 斜頂：lifter 模胚（架）： mold base 上內模：cavity insert 下內模：core insert 行位（滑塊）： slide 鑲件：insert 壓座/斜雞：wedge 耐磨板/油板：wedge wear plate 壓條：plate 撐頭: support pillar 唧嘴： sprue bushing 擋板：stop plate 定位圈：locating ring 鎖扣：latch 扣雞：parting lock set 推桿：push bar 栓打螺絲：S.H.S.B 頂板：eracuretun 活動臂：lever arm 分流錐：spure sperader 水口司:bush 垃圾釘：stop pin 隔片：buffle 彈弓柱：spring rod 彈弓:die spring 中托司：ejector guide bush 中托邊：ejector guide pin 鑲針：pin 銷子：dowel pin 波子彈弓：ball catch 喉塞: pipe plug 鎖模塊：lock plate 斜頂：angle from pin 斜頂桿：angle ejector rod 尼龍拉勾：parting locks 活動臂：lever arm 復位鍵、提前回桿：early return bar 氣閥：valves 斜導邊：angle pin 術語：terms 承壓平面平衡：parting surface support balance 模排氣：parting line venting 機械建材模具英語專業術語大全 二、運水：water line 快速接頭：jiffy quick connector plug/socker 喉塞：line lpug 喉管：tube 塑膠管：plastic tube 機械建材模具英語專業術語大全 三、入水：gate 水口大小：gate size 轉水口：switching runner/gate 唧嘴口徑：sprue diameter 進入位：gate location 水口形式：gate type 大水口：edge gate 細水口： pin-point gate 機械建材模具英語專業術語大全 四、流道: runner 熱嘴：hot sprue 熱流道板：hot manifold 發熱管：cartridge heater 探針: thermocouples 熱流道：hot runner,hot manifold 熱嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圓形流道：round(full/half runner 流道電腦分析：mold flow analysis 流道平衡:runner balance 插頭：connector plug 插座