2016年最新版數控機床報警信息中英文對照

2016年最新版數控機床報警信息中英文對照WORD ERROR （T 碼錯誤）LOW OIL LEVEL （油位低）SPINPLE FAULT （主軸故障）SPINDLE ALARM （主軸報警）EXTERNAL EMG STOP （急停按鈕被按下）AC NOT READY （交流盤未準備好）SPINPLE LUBE FAULT （主軸潤滑故障）T CODE ERROR （T代碼出錯，非法T代碼）M CODE ERROR （M代碼出錯，非法M代碼）SERVO NOT READY （伺服未準備好）NC NOT READY（NC沒準備好）TURRET FAULT （轉塔故障）TURRET LIMIT （轉塔限位）DC 24V OPEN （直流24斷開）+24V NOT READY（+24V沒準備好）GRAR DRIFT （檔位漂移）PLEASE AXIS RETURN HOME（軸未回零）PLEASE DRUM RETURN HOME（刀庫未回零）AIRPRESSFAILURE（氣壓故障）UNCL TOOL FALL（松刀失?。〢IR PRESSURE DROP （壓縮空氣壓力過低）CLAMP TOOL FALL（夾刀失敗）DRUM NOT PARKED（刀庫未在原值）X ZERO POINT NOT REACHED （X 軸未回零）Y ZERO POINT NOT REACHED （Y 軸未回零）Z ZERO POINT NOT REACHED （Z 軸未回零）4TH ZERO POINT NOT REACHED （第4軸未回零）X AXIS OVERTRAVL（X軸超限）Y AXIS OVERTRAVL （Y軸超限）Z AXIS OVERTRAVL （Z軸超限）COUNTER SWITCH REEOR （計數開關故障）MASTERT RANSFER OVER TEMP （主變壓器過熱）Z AXIS NOT AT FIRST REF POSITION （Z軸未在第一參考點）SPINDLE ORIENTATION FALLURE （主軸定向失敗）TOOL DESENT OR TOOL DATA REEOR （刀具數據錯誤）PLEASE UNLOAD THE TOOL ON SPRINELK （請卸下主軸上的刀）PLEASE LOAD TOOL ON APINDLE （請裝上主軸上的刀）A AXIS UNCLAMP FAIL （A 軸松開失?。〢 AXIS CLAMP FAIL （A 軸夾緊失敗）DRUM OUT TO APRONDLEIS FALL （刀庫擺向換刀位失?。㎝G SWING OVERLOAD（刀庫擺動過載）DRUM BACK PARK IS FALL （刀庫擺回原始位失?。㏕URRENT MOTOR1 OVERLOAD （刀庫移動電機過載）COOLANT MOTOR OVERLOAD （冷卻泵過載）DRUM ATC FAULT （自動換刀失敗）TOOLS UNLOCKED （刀具未鎖緊）BATTERY ALARM （電池報警）DRUM POSITION SWITCH ERROR （刀庫位置檢測開關故障）DRUM NOW NOT AT PARK （刀庫未在原始位置）IT DANGOU TO MOVE DRUM （刀庫禁動）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下動作失?。㊣T IS DANGOUR TO MOVE ARM （機械手禁動）THE SPINDLE STATU IS ERROR （主軸狀態錯誤）ARM MOTOR OR ARM SWITCH FALL （機械手或機械手開關故障）CENTRE LUBRICATION FALL （中心潤滑故障）THE WORK NOT CLAMPED （工件未夾緊）AUTO TOOL CHANGE FAULT （自動換刀失?。㏕OOL DATA OUT OF RANGE （指令刀具號超出范圍）THE ORDER TOOL NOW IN SPINDLE （目標刀具在主軸上）THE THREE SPINDLE SWITCH FAULT （主軸上的接近開關）THE CENTRE COOLANT IS LOWER （刀具內冷泵液位過低）DRUM RETURN 1# POSITION FAULT （刀庫自動回零失?。㏒PINDLE OVERLOAD （主軸過載）關注我們的微信公眾號shukongzhpngguo，獲取更多數控技術文章。TURRENT MOTOR OVERLOAD （刀盤轉動電機過載）CHIP CONVEYER OVERLOAD （拉屑器過載）HARD LIMIT OR SERVO ALARM （硬限位或伺服報警）NO LUB OIL （無潤滑油）INDEX HEAD UNLOCKED （分度頭未鎖緊）MT NOT READY（機床沒準備好）MG OVERLOAD （刀庫過載）LUB EMPTY（潤滑無油）AIR PRESSURE（氣壓不足）COOLANT NOT READY（冷卻沒準備好）LUBE EMPTY（油霧油位低，潤滑油位低）LUB PRESSURE LOW（潤滑壓力低）CONVEY VERLOAD（排屑過載）LUB OVERLOAD（潤滑過載）LUBE PRESSURE LOW（油霧壓力低）SERIAL SPINDLE ALARM (串行主軸報警)NC BATTERY LOW ALARM(NC電池低報警)MAGAZINE MOVE LIMIT SWITCH ERRORSPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERRORMAGAZINE NOT IN POSITION OR SENSOR ERRORAIR PRESSURE LOW ALARM(氣壓低報警)MOTOR OVERLOAD(電機過載)T CODE MAGAZINE TOOLST CODE 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERRORDOOR IS OPENED(開門)LUB PRESSURE SWITCH ERROR(油壓開關錯誤)SPINDLE OIL COOLANT UNIT ERRORSPINDLE LOAD ABNORMAL（主軸負荷異常）TRANSDUCER ALARM（傳感器報警）BED-HEAD LUBRICATE OFF（床頭潤滑關閉）EMG OFFHYDRAULIC CHUCK PRESS LOW（液壓夾頭壓力低）HYDRAULIC TAIL PRESS LOW（液壓尾座壓力低）LUB 0IL LOW（油壓低）TURRET CODE ERROR（轉塔碼錯誤）TURRET RUN OVERTIME（轉塔運行超時）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOCKTRY TO RUN SPINDLE WHILE TAIL NOT LOCKSPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REFAFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED（X 軸被鎖定）Y AXIS IS LOCKED（Y 軸被鎖定）Z AXIS IS LOCKED（Z 軸被鎖定）A AXIS IS LOCKED（A 軸被鎖定）SPINDLE MOTOR FAN QF26 OFF(主軸電機風扇QF26關閉)關注我們的微信公眾號shukongzhpngguo，獲取更多數控技術文章。SPINDLE ORIENTATION INCOMPLETE（主軸定位不完全）M FUNCTION NOT COMPLETE（M 功能無法完成）SPINDLE NOT IN GEAR POSITION（齒輪不在主軸位置）SPINDLE NOT CHANGED TO LOW GEAR（主軸沒有變?yōu)榈蜋n）SPINDLE NOT CHANGED TO HIGH GRAR（主軸沒有變?yōu)楦邫n）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,MAG.JOG SWITCH ONHYDRAULIC MOTOR QF7 OFF（ 液壓馬達QF7關閉 ）HYDRAULIC TEMPRETURE HIGH（ 液壓使用溫度高 ）HYDRAULIC FILTER BLOCKED（液壓過濾器阻止）HYDRAULIC OIL LEVEL LOW（ 液壓油位低 ）HYDRAULIC FAN QF8 OFF（液壓風扇QF8關閉）HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF（冷卻液電機QF12關閉）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTESINNER COOLANT BLOCK（內冷卻堵塞）SPINDLE COOLANT MOTOR QF14 OFF（主軸冷卻液電機QF14關閉）INNER COOLANT QF13 OFF（內冷卻液QF13關閉）MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW（低氣壓）SPINDLE COOLANT MOTOR FAULT（主軸冷卻液電機故障）LUB.OIL IS LOW（潤滑油低）DOOR OPEN（門打開）FRONT DOOR(R) OPEN（前門打開）LEFT DOOR OPEN（左門打開）LUBRICATION OIL QF23 OFF（潤滑油QF23關閉）LUBRICATION PRESS LOW（潤滑油位低）IN ADJUST,MAG CANT EXCHANGE T（在調整，刀庫不能交換T）NOT ALL DOOR CLOSED（門沒有全部關閉）IN M06,MAG NOT READY（在M06，刀庫未準備好）MAGAZINE NOT READY（刀庫未準備好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETEPOCKET NOT HOR./MAG NOT BCKWRDPOCKET NOT VER./MAG NOT FORWRDUNCLAMP TOOL HAS NOT COMPLETEDCLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZ NOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ONZ NOT IN PSW2,FORBID MAG FORWARDCHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 設定D499為0K PARAM ABOUT MAG SET IS WRONG 關于MAG的K參數設定錯誤MECHANICAL BRAKE NOT RELEASED機床抱閘沒有松開MECHANICAL BRAKE IS WRONG 機床抱閘錯誤PLEASE ADD LUB.OIL 請加潤滑油PROBE BATTERY VOLTAGE IS LOW 探頭電池電壓低PROBE IS ERR 探頭錯誤PARAMETER WRITE ENABLE（參數寫使能）PMC EDIT ENABLE（PMC編輯使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS 主軸檔位信號消失T_CLAMPED_SIGNAL MISS T夾緊信號消失SP OVERRIDE SWITCH DISCONNECTION 主軸倍率開關斷路FEED OVERRIDE SWITCH DISCONNECTION 進給倍率開關斷路THE TOTAL NUMBER OF POCKETS SET ERRCHANGE T STOPED BECAUSE NO AIR 因為缺少壓空交換停止THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷卻水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATER 冷卻水液位低PLEASE REPLACE CNC BATTERY QUICKLY 請立即更換CNC電池SIEMENS常用縮略語A Output 輸出ASCII American Standard Code for Information Interchange 美國信息交換標準代碼AV Preparation for work 運行準備BA Operating mode 運行方式BAG Operating mode groups 運行方式組BB Ready for operation 準備好運行BCD Binary Coded Decimals 二-十進制BHG Hand-held terminal 手提終端BOF User interface 用戶接口CNC Computerized Numerical Control 計算機化數字控制CP Communication Processor 通迅處理器CPU Central Processing Unit 計算機中央處理裝置CR Carriage Return 托架折回CSB Central Service Board(PLC module) 中央維護板，PLC 模塊CTS Clear To Send 發送使能DAU Digital-Analog Converter 數模轉換器DB Data Block 數據塊DIN German Industrial Standards 德國工業標準DIO Data Input/Output 數據輸入/輸出DRF Differential Resolver Function 差分功能DRY Dry Run 空運行DSB Decoding Single Block 譯碼單段DSR Data Send Ready 備用輸入DW Data Word 數據字E Input 輸入EIA-Code Special tape code,number of holes per characters always odd 特殊紙帶碼，每個字符的孔數為奇數EPROM Programm memory with fixed program 有固定程序的程序存儲器E/R Controlled Supply and Energy Recovery Module 可控電源和能量恢復模塊ETC ETC key:Extension of the softkey bar in the same menuETC 鍵：同級菜單擴展鍵FDB Product designation database 產品指定數據庫FIFO First in First Out 先進先出FRA Frame module 幀頻模塊FRAME Coordinate conversion with the components zerooffset，rotation，scaling，mirror-imaging 坐標換算，具有零點偏置，坐標旋轉，標度功能和鏡向功能FRK Cutter radius compensation 銑刀半徑補償FST Feed Stop 停止進給GUD Global User Data 全體用戶數據HMS High-Resolution Measuring System 高分辨率測量系統HSA Main Spindle Drive 主軸驅動HW Hardware 硬件IM Interface Module 接口模塊IM-S/R Interface Module(S=send/R=receive) 接口模塊，S=發送/R=接收INC Increment 步進增量ISO-Code Special tape code,number of holes per character always even特殊紙帶碼，每個字符的孔數為偶數K1.k4 Channel 1 to Channel 4 通道1 到通道4KOP Ladder Diagram 梯形圖KV Loop-Gain Factor 增益系數KUE Transformation Ratio 傳動比LCD Liquid Crystal Display 液晶顯示LED Light Emitting Diode 發光二極管顯示LUD Local User Data 局部用戶數據MB Megabyte 兆字節MD Machine Data 機床數據MK Measuring Circuit 測量回路MDA Manual Data Automatic 手動輸入，自動執行MLFB Machine-readable product designation 機器可識別的產品代號MMC Man Machine Communication:User interface of the numerical controlsystem for operation,programming and simulation 人機通訊：系統操作界面，用操作，編程和模擬MPF Main Program File：NC part program(main program)NC 零件程序，主程序MPI Multi Point Interface 多點通訊接口MSTT Machine control panel 機床控制面板NC Numerical Control 數字控制NCK Numerical Control Kernel(numerical krnel with block preparation,traversing range etc.) 數字控制核心：具有程序段預處理,運行范圍等等NCU Numerical Control Unit 數控單元NURBS Non Uniform Rational B Spline 非均值有理B樣條NV Zero Offset 零點偏置OEM Original Equipment Manufacturer 原設備制造商OP Operator Panel 操作面板OPI Operator Panel Interface 操作面板接口PC Personal Comprter 個人計算機PCMCIA Personal Computer Menory Card International Association 接口協議PG Programming Device 編程器PLC Programmable Logic Control 可編程邏輯控制器PRT Program Test 程序測試RAM Random Access Memory 隨機存取存儲器RISC Reduced Instruction Set Computer 處理器，具有指令組小、通過能力強ROV Rapid Override 快速修調RPA R Parameters Active(NCK memoty area for R parameter numbers)R 參數有效，NCK 中用于R 參數號的存儲器