【BS英國標準word原稿】BS EN 1337-4-2004 Structural bearings. Roller bearings.doc

，如果你需要更多標準可以到/kmust1進行免費查閱。 如果你購買的文檔存在缺頁、字跡模糊、亂碼等情況，請大家通過論壇消息與我聯系。british standardbs en1337-4:2004structural bearings part 4: roller bearingsthe european standard en 1337-4:2004 has the status of abritish standardics 91.010.30 ，如果你需要更多標準可以到/kmust1進行免費查閱。 如果你購買的文檔存在缺頁、字跡模糊、亂碼等情況，請大家通過論壇消息與我聯系。bs en 1337-4:2004national forewordthis british standard is the official english language version ofen 1337-4:2004. together with bs en 1337-6:2004 supersedesbs 5400-9.1:1983 which will remain current until the publication of the remaining parts of the bs en 1337 series.the uk participation in its preparation was entrusted to technical committeeb/522, structural bearings, which has the responsibility to:aid enquirers to understand the text;present to the responsible international/european committee any enquiries on the interpretation, or proposals for change, and keep the uk interests informed;monitor related international and european developments and promulgate them in the uk.a list of organizations represented on this committee can be obtained on request to its secretary.cross-referencesthe british standards which implement international or european publications referred to in this document may be found in the bsi catalogue under the section entitled “international standards correspondence index”, or by using the “search” facility of the bsi electronic catalogue or ofbritish standards online.this publication does not purport to include all the necessary provisions of a contract. users are responsible for its correct application.compliance with a british standard does not of itself confer immunity from legal obligations.summary of pagesthis document comprises a front cover, an inside front cover, the en title page, pages 2 to 31 and a back cover.the bsi copyright notice displayed in this document indicates when the document was last issued.amd. no.datecommentsthis british standard was published under the authority of the standards policy and strategy committee on28 july 2004 bsi 28 july 2004isbn 0 580 44117 2amendments issued since publicationeuropean standard norme europenneeuropische normen 1337-4april 2004ics 91.010.30english versionstructural bearings - part 4: roller bearingsappareils dappui structuraux - partie 4: appuis rouleaulager im bauwesen - teil 4: rollenlagerthis european standard was approved by cen on 2 february 2004.cen members are bound to comply with the cen/cenelec internal regulations which stipulate the conditions for giving this european standard the status of a national standard without any alteration. up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the central secretariat or to any cen member.this european standard exists in three official versions (english, french, german). a version in any other language made by translation under the responsibility of a cen member into its own language and notified to the central secretariat has the same status as the official versions.cen members are the national standards bodies of austria, belgium, cyprus, czech republic, denmark, estonia, finland, france, germany, greece, hungary, iceland, ireland, italy, latvia, lithuania, luxembourg, malta, netherlands, norway, poland, portugal, slovakia, slovenia, spain, sweden, switzerland and united kingdom.european committee for standardization c o m i t eur o p en de nor m a l i s a ti on eur o p i s c h es kom i tee f r nor m ung management centre: rue de stassart, 36 b-1050 brussels 2004 cenall rights of exploitation in any form and by any means reserved worldwide for cen national members.ref. no. en 1337-4:2004: een 1337-4:2004 (e)contentspageforeword .41scope .52normative references .53terms, definitions and symbols .63.1terms and definitions.63.2symbols .63.3abbreviations .74functional requirements .84.1general .84.2load bearing capacity .84.3 rotation capability .95materials.95.1general .95.2carbon steel .95.3stainless steel .95.4cast steel .96design .96.1general .96.2movement .106.3curved surfaces .106.4surfaces in contact .106.5length of rollers.106.6guidance and security of rollers .106.7dimensioning of components .106.7.1dimension of roller .106.7.2dimensions of roller plates .116.7.3load distribution to other components.126.8particular requirements.126.8.1flat sided rollers .126.8.2multiple rollers.126.8.3corrosion in the contact line .126.8.4alignment of components.126.8.5alignment of bearings .126.9design coefficient of friction .126.10eccentricities.136.10.1 single rollers .136.10.2 eccentricity due to rotation moment of multiple rollers .136.10.3 transverse eccentricity .146.10.4 total eccentricity.146.11combination with other elements .147tolerances .147.1flatness.147.2surface profile .147.3surface roughness .147.4parallelism of contact surfaces .157.5diameter of multiple rollers .158conformity evaluation .158.1general .158.2control of the construction product and its manufacture.158.2.1factory production control (fpc).158.2.2initial type testing .15318.2.3routine testing . 158.3raw materials and constituents . 169installation . 1610in-service inspection . 16annex a (normative) ferrous materials . 18annex b (informative) factory production control . 19b.1general. 19b.1.1objectives . 19b.1.2documentation . 19b.1.3operations . 19b.2verifications and tests. 20b.2.1general comments. 20b.2.2monitoring of conformity . 20b.2.3tests. 20b.2.4treatment of construction products which do not conform .20b.2.5recording of verification and tests (manufacturers register) . 20b.2.6traceability . 21annex za (informative) clauses of this european standard addressing the provisions of the eu construction products directive. 22za.1 scope and relevant characteristics. 22za.2 procedure(s) for attestation of conformity of roller bearings . 24za.2.1 system(s) of attestation of conformity . 24za.2.2 ec certificate and declaration of conformity . 28za.3 ce marking and labelling . 29bibliography . 31forewordthis document (en 1337-4:2004) has been prepared by technical committee cen /tc 167, structural bearings, the secretariat of which is held by uni.this european standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by october 2004, and conflicting national standards shall be withdrawn at the latest by january 2006.this document has been prepared under a mandate given to cen by the european commission and the europeanfree trade association, and supports essential requirements of eu directive(s).for relationship with eu directive(s), see informative annex za, which is an integral part of this document. the european standard en 1337 “structural bearings” consists of the following 11 parts:part 1general design rulespart 2sliding elementspart 3elastomeric bearingspart 4roller bearingspart 5pot bearingspart 6rocker bearingspart 7spherical and cylindrical ptfe bearings part 8guide bearings and restrain bearings part 9protectionpart 10inspection and maintenancepart 11transport, storage and installation annex a is normative and annex b is informative. this document includes a bibliography.according to the cen/cenelec internal regulations, the national standards organizations of the following countries are bound to implement this european standard: austria, belgium, cyprus, czech republic, denmark, estonia, finland, france, germany, greece, hungary, iceland, ireland, italy, latvia, lithuania, luxembourg, malta, netherlands, norway, poland, portugal, slovakia, slovenia, spain, sweden, switzerland and united kingdom.1scopethis part of en 1337 specifies the requirements for the design and manufacture of single and multiple roller bearings, in which the roller axis is horizontal. in order to accommodate displacements parallel to the roller axis roller bearings can be combined with sliding elements in accordance with en 1337-2. to permit rotation about the axis perpendicular to the roller axis or about both axes, as for multiple roller bearings, the roller bearings can be combined with bearings from other parts of en 1337.this part of en 1337 does not apply to roller bearings made with materials other than those specified in clause 5. bearings which are subjected to rotation greater than 0,05 rad resulting from the characteristic combination ofactions are outside the scope of this part of e