PSCAD與電弧相關的模型

1、Shan JiangManitoba HVDC Research CentreWinnipeg, Manitoba，CanadasupportPSCAD與電弧相關的模型及示例斷路器合閘“statistical breaker close” 元件斷路器分閘“breaker arc”元件“reignition”元件 Restrike 重擊穿故障電弧“fault arc”元件電弧爐(EAF)“EAF”元件Page 2斷路器合閘特點斷路器可以在基頻周波的任意一點合閘暫態因合閘點不同而異(Point On Wave - POW)每相的合閘時間符合正態分布(normal distributed)Page

2、3斷路器合閘Pre-insertioncontactresistorMain contactPage 4TbTb+DtaTb+DtmDtaDtmclose requestclose pre-insertion contactsclose main contactsT(sec)TaTm斷路器合閘注: 每相的合閘時間符合正態分布Page 5Page 6Statistical breaker close均數 =2標準差 =1，對應出現概率 68.2%標準差 =2，對應出現概率 95.4%標準差 =3，對應出現概率 99.7%標準差 =4，對應出現概率 99.999%Page 7Statistical

3、 breaker closeIf cls = 0.9, the closing time of the three phases will lie in area: (cls+0.1, cls+2.1) = (1, 3)Mean delay: = (0.1 + 2.1)/2=1.1time to issue “close request”close signalThe component in master library of PSCAD4.6Page 8Statistical breaker close例子: 檢查不同的合閘時間對暫態的影響注: 通常需要與“multiple run”一起使

4、用Page 9斷路器分閘電流截斷過程觸頭分離瞬間，電弧隨之建立截流總發生在電流過零時刻截流瞬間，暫態恢復電壓(TRV) 隨之出現截流成功與否取決于TRV及斷路器自身參數(重燃和重擊穿)PSCAD中創建的模型及例子“breaker arc”: 模擬電弧電阻的變化過程“reignition”: 模擬電弧重燃現象Restrike example: 重擊穿現象Page 10Breaker Arc模擬斷路器電弧三種方式：Thermal & dielectric recovery modelParameter modelArc-circuit interaction modelThe third one

5、is selected in PSCADPage 11Breaker Arc斷路器電弧：純電阻性， 非線性影響電弧電阻的因數:Power injected to the plasma channel by the systemCooling powerArc time constant of the breaker傳統模型：Mayr model: the arc near to the current zeroCassie model: the arc in the high current time intervalPage 12Breaker Arccontacts start to se

6、parate, arc resistance calculation startsArc voltage and currentarc resistancePage 13Breaker ArcExample: test circuit of “breaker arc”Page 14Breaker ArcMayr modelCassie model弧后電流(Post arc):源于TRV及過零瞬間電弧電阻未達到無窮大TRVTRV:主要由電源側 LC 電路造成Page 15Schavemaker modelBreaker ArcPage 16re-ignitionAfter the tempora

7、rily current interruption, if the dielectric withstand is less than TRV, the dielectric breakdown occurs.Problems:Voltage escalationExtending the arcing time, damaging the breakerCan happen on any breaker, most serious on VCB during small inductive current interruptionPage 17Arc re-ignitionPage 18Ar

8、c re-ignitioncontacts start to separate, arc formsArc voltage and currentBreaker control signalPage 19Arc re-ignitionExample: test circuit of “reignition”Page 20Arc re-ignitionSimulation results of “reignition”ignitioninterruption11 re-ignitions11 re-ignitionsTRV increases (voltage escalation)Page 2

9、1Arc restrike Restrike:The dielectric breakdown after 1/4 cycle of the power frequency, following interruption of a capacitive current at a normal current zeroResult: voltage escalation which can damage the breaker and other equipmentDifferences between re-ignition and restrikeOccurrence time:Re-ign

10、ition 1/4 fundamental cycle after current zeroMechanism:Re-ignition: high rate of rise of recovery voltage (RRRV)Restrike: the high voltage magnitude due to the trapped chargeCircuit:Re-ignition: inductive current (shunt reactor switching)Restrike: capacitive current (capacitor switching)Page 22Arc

11、restrike Current interruptedMultiple restrikesPage 23An arc forms at the fault point during Single Line to Ground fault (SLG). Primary arc: before breakers openSecondary arc: after the breakers tripSecondary arcA small current remains: the capacitive couple between the fault conductor and the “healt

12、h” conductorsExtinct at current zero, and may reignite due to fast rising recovery voltageVital to the Single Phase Auto-reclose (SPAR)Features Pure resistive, time viriable & hilghly nonlinearFault arcV-I cyclogram of secondary arcPage 24Model: the arc conductancePrimary arcSecondary arcThreshold v

13、oltage of re-ignitionFault arcPage 25Fault arcBreaker statusFault signalPage 26Fault arcExample: SPAR study and neutral ground reactor (NGR) designPage 27Fault arcSimulation resultsSLG appliedBreaker openSecondary arc currentRecovery voltageArc extinguishedPage 28Electric arc furnace (EAF)Power qual

14、ity problemsHarmonicsFlickervoltage imbalanceModeling:Modeled as a voltage source series with a resistorPower balance equation Page 29Electric arc furnace (EAF)Adjusting k1, k2, k3 to find a V/I characteristics which matches the measured one.Page 30Electric arc furnaceExample1: EAF with SVCPage 31Electric arc furnaceExample2: EAF with STATCOMPage 32References:“PSCAD model report-statistical breaker close”, shan“PSCA