充電電池的基本測試要求簡介-20090915

1、Ti TEST RITEYour GloCal Service Partner.Rechargeable battery basic test requirementsimple introduction (For QC reference)充電電池的基本測試要求簡介（QC參考）SZO-QATonna GuanSep 15, 2009 Contents:-EN61951-l:2003Sec on dary cells and batteries containing alkaline or other non-acid electrolytes-Portable sealed recharge

2、able single cellsParti: Nickel-Cadmium含堿性或其他非酸性電解質的二次電池和蓄電池便攜密封可再充電單電池 第1部分一鐮鎘電池.-EN61960:2004Sec on dary cells and batteries containing alkaline or other non-acid electrolytes Sec on dary lithium cells and batteries for portable applications裝有堿性或其它非酸性電解液的蓄電池和電池組用于便攜式的充電鋰電池和電池組-ANSI C18.2MPARTI: Ame

3、rican national standard for portable rechargeable cells and batteries-Geneal specifications第一部分：便攜式充電電池的美國標準一般要求-Battery Dimension電池尺寸 EN61951-l:2003Sec on dary cells and batteries containing alkali ne or other non-acid eIectroIytes-PortabIe sealed rechargeable single cellsParti :Nickel-Cadmium含堿性或其

4、他非酸性電解質的二次電池和蓄電池便攜密封可再充電單電 池第1部分銀鎘電池.5.3 Marking標識Charging procedure for test purposes充電的測試流程Discharge performs nee at 20 C20C環境溫度下的放電性能5.3 Marking標識Each jacketed cell supplied without connections shall carry durable markings giving the following minimum information:每個單獨電池要提供至少包括以下信息的耐久標識：-Sealed, r

5、echargeable nickel-cadmium or Ni-Cd密封的，可充電的鐮鎘-Cell desig nation電池類型Rated capacity額定容量Nominal voltage標稱電壓Recommended charge rate and time or permanent charge current for、T cells對于T電池（預計在達到40C高溫下永久充電的電池），建議的充電速度和時間或永久充電電 流-Polarity極性Date of manufacture （which may be in code）生產日期（可以使用代碼）Name or identif

6、ication of manufacture or supplier制造商或供應商的名稱或身份識別 7.Charging procedure for test purposes充電測試流程Un less otherwise stated in this start dard, the chargi ng procedure for test purposes shall be carried out in an ambient temperature of 20C5C at a constant current of O.lItA for 16h(It A=CnAh/lh)除非本標準特殊說明，

7、充電程序是在20C5C環境溫度和O.lItA的恒電流下充 電16hPrior to charging, the cell shall have been discharged in an ambient temperature of 20C5C, at a constant current of 02ItA down to a final voltage of 1.0V充電前，電池在20C5C環境溫度下且在02ItA的恒電流下已放電到終止電壓為 1.0V 7.2.1 Discharge performance at 20C20C環境溫度下放電性能The cell shall be charge

8、d in accordance with 7.1.After charging, the cell shall be stored, in an ambient temperature of 20C5C,for not less than lh and not more than 4h電池按照71條款充電，充電后，要將電池在20C5C環境溫度下存放14hThe cell shall be discharged at 0.2It A rate in an ambient temperature of 20C5C to a final voltage of 1.0V, if the test is

9、 based on the rated capacity C5Ah (5 is the time base in hours for which the capacity is declared), the minimum discharge du rati on shall be 5h電池在20C5C環境溫度下且在0.2ItA的恒電流下放電到終止電壓為1OV如果測試是根據額定容量C5Ah(5表示宣稱容量的放電時間基數以小時表示)來進 行的，放電時間不能小于5hEN61960:2004Sec on dary cells and batteries containing alkali ne or

10、 other non-acid electrolytes-Secondary lithium cells and batteries for portable applications 裝有堿性或其它非酸性電解液的蓄電池和電池組用于便攜式的充電鋰電池 和電池組5.3 Marking標識7.1 Charging procedure for test purposes 充電的測試流程7.2.1Discharge performanee at 20C (rated capacity) 20C環境溫度下的放電性能(額定容量)5.3 Marking標識Each cell or battery shall

11、 carry clear and durable markings giving the following information: 每個電池應按照如下信息提供清晰，耐久的標識：-Rechargeable Li or Liion;可替換的鋰或鋰離子-Battery or cell desig nation (e.g.ICR19/66 )電池類型-Polarity極性Date of manufacture (which may be in code)生產日期(可以用代碼表示)-Name or identification of manufacture or supplier制造商或供應商的名稱

12、或身份識別Battery marki ngs shall provide the following additional in formation:電池標識要提供如下額外信息：-Rated capacity額定容量Nominal voltage標稱電壓 7.1 Charging procedure for test purposes 充電測試流程Prior to chargin the cell shall be discharged at 20C5C, at a constant current of 0.2It A down to a specified end -of -dischar

13、ge voltage充電前，電池要在20C5C環境溫度和在0.2ItA的恒電流下放電到終止電壓為 1.0VCells or batteries shall be charged, in an ambient temperature of 20C5C, using the method declared by the manufacture電池在20 C 5 C的環境溫度下使用制造商宣稱的方法充電 7.2.1 Discharge performance at 20 C (rated capacity) 20C環境溫度下的放電性能(額定容量)Step 1-The cell or battery s

14、hall be charged in accordanee with 7.1 步驟1 電池根據71條款充電Step2-The cell or battery shall be stored , in an ambient temperature of20C5C ,for not less tha n lh and not more th a n 4h步驟2電池在20 C5C的環境溫度下存放，時間在lh4hStep3-The cell or battery shall be discharged, in an ambient temperature of 20C 5 C z at a const

15、ant cur re nt of 0.2It A, until its voltage is equal to the specified end-of-discharge voltage步驟3電池在20 C5C的環境溫度下且在0.2It A的恒電流下放電直到電壓達到特 指的終止電壓Step 4-The capacity (Ah) delivered during step 3shall be not less than 100%of therated capacity declared by the manufacture Steps 1 to 4 may be repeated up to

16、 four additional times, as necessary to satisfy this requirement步驟4-在步驟3中得到的容量不能小于制造商宣稱的100%的額定容量。為了滿足本要求， 1到4步驟可以再重復進行四次ANSI C18.2M PARTI: American national standard for portable rechargeable cells and batteries-General specificationsANSI C18.2M第一部分：便攜式充電電池的美國標準一般要求Charge method: Charge for 20h at

17、O.lC-rate. Let rest lh.充電方法：電池在0.1C下充電20h，停放lhRated Capacity and service life: Discharge at 0.2C-rate until terminal voltage=cut off voltage (EODV) of l.OV/cell.Calculate and report capacity. Shall meet or exceed claimed capacity.額定容量和使用壽命：在02C下放電直到終止電壓為1OV，計算容量，實際容量 應滿足或超過宣稱容量值Battery Dimension電池尺寸

18、:Cylindrical cells dimensionally interchangeable with primary battery在尺寸上與原電池可互換的圓柱形電池(Ni-Cd)Stan da rd: in accorda nee with IEC60086-2標準：根據IEC60086-2Designation: R03(alson known as AAA), R6(alson known as AA) 類型：R03 (在某些國家也稱作AAA)，R6 (在某些國家也稱作AA)Dimensional drawings as figure 1&2尺寸圖表示如圖1&2 Specifications as tablet尺寸要求如表1Figure 1FFigure 2Desig nation類型Dimensions mm 尺寸mmACFG0 -0,743.0KR 15/5114.550.5KR