注塑模具DFM-報告模板

1、Parts Analysis Report“Engineering global parts”Project No.:10CE697.3Part Name.: housing產品名項目號cavitycoreACTUATOR HANDPLBanana gate will be in hereBasic Mold InformationCavitySlider/LifterResinShrinkSteelGate TypeMold Type出數斜頂行位數膠料縮水率鋼料入水形式模具類型1X2NONEABS1.005H13Cold runner with sub gate2 plate moldshr

2、inkage rate correct?Kindly adviseVisible area _確認外觀面Is this part a visible one? If so kindly advise the where the visible area .表達運水表達流道表達放大圖位置GGSection G-G基本直線基本箭頭(1.0mm)(1.0mm)表達各種尺寸表達截面一些有用的圖形基本文本框AAplease advise表達運水表達流道基本直線基本文本框please advise鼠標在直線上點擊右鍵，再點擊設置為默認線條，設置好后就可以畫出與這條線一樣的線條啦！PS：設置好默認線條后，默

3、認箭頭會自動設置好！同理，文本框與運水，流道也可以右鍵設置默認來方便畫Layout _模具排位表達運水表達流道Slide行位斜頂lifterInserts split line _鑲件線確認Insert here, OK?這里做鑲件,OK?Insert split line in red, OK?紅色鑲件線,請確認Ejection _產品頂出確認Ejector bladeEjector sleevesEjector pinslifterInner slideSurface finish_產品拋光/曬紋位置確認Is this part a visible one? If so please ad

4、vise the which the visible area is and the surface finish spec.MT11010 texture for red surface, please confirm.紅色面曬MT1101紋,請確認Other surface apply Sandpaper 600# for mold release., please confirm.其它面省到600#砂紙出模,請確認Draft Study _產品斜度分析Green surfaces without draft angle now, suggest to enlarge to 1 degre

5、e at least (by reduce material) Kindly advise.綠色面直身,建議最小減膠加1度斜度,請確認.Draft angle of the shut off surfaces (red marked) is not enough , least (by reduce material) it should be 3 degree at least.圖示紅色面擦穿，斜度不足（單邊最小3度）the red surface is straight, suggest add 3 draft angle on it (by reduce material) for te

6、xture MT0000, least (by reduce material), pls confirm. 紅色直身面,建議減膠加3度出模角來曬紋MT0000,請確認.Wall thickness study _產品壁厚分析Red area with uneven thickness, may cause sink marks, please help improve.紅色區域壁厚不平均,太厚了,可能縮水,請幫忙改善.Those ribs too thick, suggest thin them to 75% general part surface to avoid sink mark o

7、pposite it. Please confirm.箭頭所指骨位太厚,建議減薄到基本壁厚的75%來避免骨位對面縮水痕.請確認.Wall thickness well distribute.壁厚OK.Part tolerance study _產品公差合理性分析We did not get the part 2d drawing yet, would you please sent to us? Drawing with critical dimensions (tolerance) and note the criticalsurface will be great! 請?zhí)峁┌钆c高要求

8、表面的產品2D產品圖Provide information above before mold designing can help our engineer make the correct decision during design & manufacture, so we will get the perfect part and the lead time wouldnt be extended. Thank you!Tolerance here may too tight to injection, can it enlarge to +/- 0.2mm?這個公差太緊了,注塑很難保

9、證,是否可以加大到+/- 0.2mm?Warpage prevent _知悉客戶可能的產品變形Engraving & cav. N.O _產品曬字合理性分析與模穴號確認Does this part need date wheel, recycle mark, or mark the part number?這個產品是否要加日期章/環保標記/模穴號?Cav. Number here, text height 1.5mm raise 0.2mm,OK?在這里加模穴號,字高1.5mm, 高出產品0.2mm,OK?Suggestion _產品結構改善建議回復DFM的一般是客戶公司的產品工程師，他們大部分對模具并不熟悉，這就要求我們的模具工程師在做DFM時要考慮到這一點，提出的產品問題應盡可能給到量化的方案：如“骨位太厚，要減薄，請確認”，這一句更好的表達應該是“這條骨位太厚，可能導致產品表面有縮痕，建議減薄到根部1.2mm，請確認?！睒?biāo)準的表達可以參考： 問題+可能導致的后果+量化的解決方案。如：問題（骨位太厚）+可能導致的后果（表面有縮痕）+量化（根部1.2mm ）的解決方案（減薄根部）。更好的表達可以是：量化建議+可以解決的什么問題。如：建議減薄到根部1.2mm，以防止產品表面有縮痕，請確認。Suggestion