模具英語詞匯大全

1、汽車沖壓模具英語詞匯Die / Tool= 模具Prog. Die=progressive die 級進模Ball bearing guide posts and bushings=球形滾珠導柱和軸套Casting die=鑄造模Cage=套Part=鈑件Rigidity=強度Die material=制模材料Thin=薄Tool design=模具設計Strip design=料條設計Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chippe

2、d punch or die corners in the tool. =在尖角處使用與材料厚度一樣的R角減少沖頭碎裂或模具中有“刀口”Tool design approval=模具設計審核Tool design modification/revision=模具設計更改Tool parts design (detail) =模具鈑件設計（詳細）Heeled die sets, internally heel form & trim sections=帶箱根的模架，成形與切刃沖頭帶導引FMC Make=保麗龍制作Construction method=結構方法modification= 更改Ch

3、eck & measure=檢查 & 測試Machining= 機器加工Large machining=在大型機器上加工上下模架（銑、車等）Small machining=在小型機器上加工模塊等Lower die trim inserts=下模切刃塊Lower trim inserts retainer=下模切刃塊承盤Assemble inserts=組立鑲塊Punch stripping plates=沖頭壓料板Assembly=組立Trim punch backing plates=切刃沖頭背板NC Machining=NC雕刻加工Stripper window inserts=料條窗戶鑲

4、塊Fitting=研磨組立Spotting=合模Die tryout=試模Cushing stroke=緩沖行程Dowel pin=定位銷Guide lift pin=導引升降銷Assemble gas spring=安裝氮氣缸Stamp parts=沖鈑件Adjustment=調試Run off parts=沖鈑件Lower trim steels=下刃塊Hit parts=沖鈑件Section=沖頭斷面Lifters=提升器Trim punch=切刃沖頭Coil=卷材jack screw hole=起重千斤頂螺旋孔Guide block=導引塊Die set, lower plate=下模

5、架Guide the coil through the tool=導引卷材Die set, upper plate=上模架layout inspection=全尺寸檢驗Die inspection & approval=模具檢查和審核Stretch carriers=拉伸運送裝置delivery=發貨Punch stripping plates=沖頭壓料板Rejected=拒收Trim punch backing plates=切刃沖頭背板Scrapped=報廢Stripper window inserts=料條窗戶鑲塊Rework=返工Heel plates=背托stop block=停止塊

6、Prepare for delivery=準備發貨Hydro form 液壓成形Key=鍵Shear=剪切For locating retainer blocks=承盤鍵Sensor=傳感器For holding buttons or pilots=沖母座或導銷鍵Stretch web=拉伸網For fixed heel or positive stop=鑲根鍵Layout the parts=設計鈑件Construction method=結構方法Preceding into the design=繼續設計Manual Surface Grinder=手動平面磨床Guide the coil

7、 through the tool=導引卷材Spotting red=合模用丹紅Checking aid /checking gage=檢具Layout ink=試模用藍墨水Jig=夾具Masking tape=黃色不透明膠帶(遮蔽膠帶)Fixture=夾具Pliers=尖嘴鉗，老虎鉗Ball bearing guide posts and bushings=球形滾珠軸套Cresent wrench=可調扳手Guide post=導柱Bushings=導套Pump pipe=泵管Using material thickness radii where sharp corners are sho

8、wn on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角處使用與材料厚度一樣的R角減少沖頭碎裂或模具中有“刀口”CMM=三次元測量儀Symmetric=對稱的The axis of symmetry=對稱軸Technical=技術上的Diagonal=對角線Heeled die sets, internally heel form & trim sections=帶箱根的模架，成形與切刃沖頭帶導引One two three block=一二三模塊Adjustable paral

9、lels=可調平行塊Stop block=阻止塊Granite Table=花崗巖平臺Backing Plate=背板Plotter= .描繪器, 圖形顯示器, 繪圖器, 坐標自記 器, 標圖員Shoulder Bolt=肩頭螺絲(Stripper bolt)Belt Sander=帶磨機Keeper Block=行程塊Metal Cutting Band Saw=立式帶鋸床Corner Guide Block=導塊 Blanchard Grinder=大型平面磨床Dowel pin=定位銷Joe Blocks=精密量塊Set Screw=螺塞Whirly Gig=筒夾式沖子成形器Jig &

10、fixture =夾具Chamfer Tools=倒角刀具組Checking fixture=檢具Angle Plate=L形直角座Guide Block=導塊Gage Pins=英寸塞規Plunger=柱塞Sine Plate (magnetic)=正弦磁臺Pierce=沖孔Flute End Mill=硬質合金鋼銑刀Wear Strip=耐磨板Mill Cutter=波紋粗銑刀（標準型）Mating area=組立的接觸面Cbore/ counter bore=六角沉頭銑刀Accommodate=適應Radius Dresser=砂輪修整器Wiping hard (very shiny)=

11、 過分摩擦閉合接觸（閃光）Boring Head & Boring Bar=搪孔器、搪刀桿Pin=銷Increase the die clearance between the form steels=增加成形塊間隙Reamer=絞刀Clearance=間隙Approval=確認Oil paper=油紙Impact wrench=氣動扳手0-11” Micrometer=0-11”千分尺Air pin=空氣銷Trim line=切邊bumperbQmpE(r) n.緩沖器+/-0.5mm unless otherwise specified除非另有規定，否則公差為+/-0.5mmVendor

12、vendE(r), -dC:(r) n.賣主Part tolerance=鈑件公差stripper layout=排樣圖Ball nose=球刀drawing of panel #987415&16=鈑件設計圖（公差）Bore=鏜Line tap=攻絲校直 Arbor =柄軸；心軸 Borer=鏜刀，鏜床Drill chuck=鉆夾頭Chamfer=倒角Button=沖母座Radius=半徑Nitrogen Cylinder=氮氣缸Coolant=切削液Pilot=導銷Punch=沖頭Retainer=承盤Distribution Blocks=接頭座Button=沖母座Screw=螺絲Hos

13、e Straps=軟管夾（塑料）Shop=車間Flat Feet Keepers=頂料銷Crib=倉庫Ejector Pin=頂出銷CNC mill= CNC機床Spring=彈簧Jack=千斤頂Straight Port Adapter=直管接頭Strips=料條Y-205 Hose=軟管（塑料）Styrofoam stairEfEumn.聚苯乙烯泡沫塑料 （保麗龍材料）Short Neck Adapter=短接頭 Cut off=落料45。 Swivel= 45。接頭(adjustable)Idle station=空站（for changeability of the part in t

14、he future）45。Elbow=45。接頭(un-adjustable)Dry run=空轉(to check the interference 干涉of a die) Compact Swivel Adapter=轉接頭 Form=成形Control Panel=控制面板Trim=切邊Stamp Retainer=承盤Perforate= p:fEreit v.打孔Spotting press=合模機Plumber=水管工人 plQmE(r)Hand grinder=角磨機Yo-yo 卷尺(美)Surface grinder=平面磨床Drill chuck=鉆頭夾Blanchard g

15、rinder=大型平面磨床Tape measure=卷尺End mill=端銑刀/立端刀Protractor=量角器Ball nose end mill=球頭銑刀Switch=限位開關Straight edge=直角座Caliper=卡尺Shim stock=墊片Slug=廢料Oversize tap=加大尺寸絲攻Fittings=接頭Die=模具Crimping machine=氮氣缸接頭夾具Upper die=上模Manual surface grinder=手動平面磨床Lower die=下模Push cart=推車Die set=模架Tool box=工具箱Button die=沖母座

16、Heel block=鑲根Pilot=導銷Tap=攻絲Bushing=襯套Feeler gage=塞尺HRS=hot roll steel =熱軋鋼卷Belt sander=砂帶機CRS=cold roll steel=冷軋鋼卷Metal cutting band saw=帶鋸（切割金屬）Insert=鑲塊Joe blocks=測量塊Guide post=導柱Scriber=劃線器Crane=吊機Zinc coating=鍍鋅Stripper pad=壓料板Ball peen hammer=球形榔頭Dowel pin=定位銷Rosin=松香水Heat treat=熱處理Wire burn=線割

17、Gage pins= Round cylinders of precise dimension used for measuring holes.Fast wire burn=快走絲Blank die=下料模Slow wire burn=慢走絲Tryout material=試模材料Stripper pad=壓料模(Pad retainer) shoulder bolt=stripper bolt=肩頭螺絲（all can be used for guiding a pad）Trim block (steel)=切刃塊Pad retainer=壓料模承盤 Form block (steel)=

18、成形塊Drill chuck=鉆夾頭Drill vice=平口夾鉗Pig putty= epoxy Putty=油灰Parallel=平行塊/肋條Sandblast=噴沙器 噴沙(a pressurized air sand mixture)Graphite =石墨（lubricant） grAfait n. Plumb=plQm n.鉛錘, 鉛彈 adj.垂直的vt.使垂直, 用鉛增加重量, 探測vi.垂直Plumber=n. 水管工人plQmE(r)Solder (lead)=sEuldE(r); (?) sodErn.焊料 v.焊接 (鉛條)Titanium nitrate (Tin c

19、oating-hard)=化硝酸鈦 (鈦化處理)Binder= baindE(r)n.環模線，裝訂工, 包扎者, 包扎工具, Adjustable locking pliers (vice grip) =可調鎖緊老虎鉗blind hole=悶眼, 盲孔Steel shavings=鐵屑 slip fit=滑(動)配合Cast iron=鑄鐵sliding chute=滑槽Threads=螺紋Ratchet wrench 棘輪扳手Spacer block=間隔體(有時也叫平衡塊)Vise grips=大力鉗Semi-stripper=半脫件Vargus debur tool=去毛刺器Clamp

20、block=楔子Disc grinder=砂輪機Killer pin=間隙調節螺栓Air drill=氣動手槍鉆Restrike=整形Hole gage=鉆頭規Extension pin=伸長銷Jack screw 起重千斤頂螺旋Conveyer=輸送器Screw hole=螺絲孔Spool retainer= 短管扣Pin hole=導銷孔Guide plate= 導板Sheer cut=剪斷Guide block= 導塊Thrust=推力Lock=鎖定Heel guide post=跟部導柱Preform=預成形Kicker pin=踢出銷Air bend= 自由彎曲Set height

21、stopper=設定高度阻止器Cam cut, cam pierce=剪斷加工Knock-out bar=頂出棒Gib=嵌條Push-back=推出Single roll feed=單滾子進給Cut=切斷Gripper feed=夾爪進給Pad=托板Grip finger=移動爪Brake finger=固定爪Slide feed=滑動進給Single gripper feed=單夾爪進給Hitch feed=緊扣進給Pinch整緣Double roll feed=雙滾子進給Flash整緣Strip feed=帶材進給Wipe down整緣Hopper feed=漏斗進給Trim flange

22、整緣Station dial feed=分站圓盤進給Horn type整緣Friction dial feed=摩擦圓盤進給Shimmy整緣Magazine feed=推進器進給Post type=柱型Transfer feed=自移進給Solid type=整體型Air blow ejector=空氣噴出Angle type=折角型Kicker=踢出件Composite type=復合型Strap=夾條Insert type=嵌入型Engineering=工程Carbide cutters=硬質合金銑刀Distance block=平衡塊Balance block=平衡塊Washer/shi

23、m=墊片Pad balancer=平衡塊Datum=基準Hopper feed=Notching punch= 凹口(局部落料)沖頭French stop(feed stop) =進給停止器End mill=立端刀, 端銑刀Transfer punch=洋沖(used for drilling)Neopreneni:Eupri:n n.化氯丁(二烯)橡膠Set punch= a male punch shape to transfer to a female punch shapeFoundry faundrin.鑄造, 翻砂, 鑄工廠, 玻璃廠, 鑄造廠Sand-cast 砂型鑄件, 砂型鑄

24、造Velocity vilositin.速度, 速率, 迅速, 周轉率Simulation-Draw die drawing拉伸模設計模擬Ball seat=眼淚水Square shear=剪板機Draw bead=拉伸筋Pitch(progression)=步距Draw lube=拉伸潤滑油Flange=折邊(通常為直邊或90折邊)，凸緣Socket(deep & shallow) ratchet=套筒扳手（深和淺） Curl=卷邊Apexs=氣動扳手Channel locks=Datum plane=.基準面Sand blast=噴砂處理，噴砂設備Plane=平面Wrench work=鉗

25、工(工作) fitter=鉗工Surface=表面 point=點 line=線Lathe man=車工 Solid=體，固體Initiator=開始者,引發劑Body=空心體Planar Mill 龍門銑床Planar pleinE(r),-na:(r) =平面的 Graphics Language=圖學語言Offset=偏置Projection=投影Draw=拉伸EsperantoespErAntEu=世界語Redraw=再拉伸Engineering Drawing=工程圖，工程制圖Blank=下料Graphic Science=圖學Split=開縫Descriptive Geometry

26、=投影幾何Notch= 做缺口Representation of Diagrams=圖表書法Separate=切離Blue Print=藍圖Emboss=壓花Original Drawing=原圖Joggle=榫接Computer Graphics=電腦繪圖Hemming=金卯合RAM=記憶體random access memoryBurr= 毛邊Plotter=繪圖機CAM=凸輪工程Geometry=幾何Hook=吊鉤Circle=圓Leader=指線Conic sections=割椎線Extension line=延伸線Ellipse=橢圓Working drawing=工作圖Parabo

27、la=拋物線Full section=全剖面Hyperbola haipE:bElE=雙曲線Half section=半剖面Straight line=直線Broken-out section=局部剖面Curves=曲線Rotated section=旋轉剖面Front view=前視圖Removed section=移動剖面Right side view=右側視圖Offset full section=偏置全剖面Left side view=左側視圖Auxiliary review=輔助視圖Top view=俯視圖Reference plane=參考平面Bottom view=仰視圖Projection weld=立式點焊機Rear view=后視圖Spot weld=點焊Six principal views=六個主要視圖Dash Panel=前隔板Sectional view=剖視圖interchangeable fixture=可互換的夾具（可拆卸）Blank die=下料模nut a