如何設置BIOS從光驅啟動

1、設置從光驅啟動：一、進入BIOS的方法根據BIOS的類型也有所不同，最常用的就是開機一直按住 Del”鍵直到進入的BIOS，界面大多如右圖:移動f JJ t光標鍵可以進行 選擇，一般設置開機啟動順序的項目就在 Advaneed BIOSFeatures "這個選項中（右圖紅 框）。FriP/PcI configurationsLoad Fail-safe DefaultsTimejratej Hard Disk Type.Load optimized DefaultsAdvanced BIOS FeaturesHeal th st at uspower HanagsetupCMOS

2、setup utilitycopyri&ht(c)1984-2001 Award softwareset supervisor passwordExit without savingset ustr passwrd$旳令 & Exit setup回車后就會出現下面的畫面:Adxnced chipsFeaturesAnti-Virur ProtectionDi-abl'sdCFU Internal CacheEnabledItem HelpEirternil CcheEii iblrdCPU L? Cache ECC CheckEn.-ibl rdMenuLevelPro

3、cefcr Nu*ber FeatureEnablrd上圖方框內的四條分Quick PostDisabledAl lows you to chooseQuick Power On Self TestErtat' H dthe VIRUS warning別為第一、第二、第三、Fitt Boot DeviceFhppyfeature for IDE HardSrond Poet T'flvi caHDD-Q1Disk boot sector其他啟動順序，如果設Third Boot DeviceLS12Gprotection If thisBoot Other DeviceEnabl

4、functicn is enabled置光驅為第一啟動順Swap Floppy triveKnablcdand some one at t enp t toBoot Up Floppy S«elrEtiabl rdwrite njata into this序的話，可以移動光標Boot Up NwnLock St at usONarea, BIOS will showGate A2D OptionFata warning message on到 First BootTypematic Rate SettingDisabledscreen and jlarm beepTypfilial：

5、 xc Rii<3叮二點r6Drive ”，然后回車，用ypeinat it* Ka+r (血*£50Security Opt ionSft i.irf J光標選擇OS Select For DRAM > 641TNon-0S2HDD Inst ant RecoveryDisabledCDROM ”，然后回車確定即可。按F10保存，然后按ESC鍵退出（可能提示存盤，按“ Y”退出就行。）二、還有一種按 Del”進入BIOS的界面如下:這種BIOS界面相對比較老一些，但也很常見，設置從光驅啟動時可以選擇Guxlnr Soft/hunehanq. ye«ih.ric

6、t> CMOS SETUP UIILITV AVftHD SOFIW口HE. INC,BIOS FEATURES SETUP ”并回車，在接下的界面中選擇Boot Sequenee ”，用f光標鍵將順序調整為CDROM , C, AHOM PCI/ISA BIOS BIOS FEATURES SETUP WARD SOFTVAM . INC,GaoYin SoftCPU In t er nd 1 Cort SpeedBoot Virus DeltectionCPU Level 1 Cec局CPU Level 2 CacheCPU Level ? Cdcl ECC CheckDisable

7、d Hdbl+'d rtdbled EhdbledBIOS Upda1«Turbo HodeQuick Power On Self (est HDD SftaiMnc* SCSI/IDE First:F ndbid :Disabled :Lrvdblcd:IDEPCl/VCn Palette ROH BIOS CBFFF CFFFf D3fH MFI -DBFFF -DFFFFVideoC890OCCO0Ooeoeo0406908000PCOO0SnoopShtido*ShBrlowShddoNShadowShodotffShadowSEukdoM StatusDisable

8、d:En.ib :r n<ib :En(ib :Endb :En<ib :ndb :I n<ib :On :DisabledcdBoot Sequence: CDROHPCTflBoot Up F OPPV Seek: E DfibedFloppy Disk Access Control : R/WIDE HDD Block Mode Sectors : Disabled Hl)() S.H.R. R. T. cdpubi 11: Enabled PS/2 Housa Fund ion Control: AutoOS/? Onbotird Heworv > 64H: D

9、i sob 1Boot Up NunLck 讓 Rate SettingTpendt ic Rdte (Chur/Sec): 6 TvPMcit ic Del up (Hcsc): 250Secur 1Opt ion: Seh»pESC : QuitTl* i Select ItemFl : HelpPU/PD/*/- : HodiFvF5 : Old Values (Shift)F2 : Color f6: Lorid DIOSJ I ; Loadb按F10保存退出。BIOS SETUP UTtLJTVAdvancedFwerBootSecurityExit備IK? Persian

10、 :(MLOO.OBIOS Build De.te :08zl4/63System tlowtry；1GAHJII ：S7：利Syten DdtECUed 05/23吃005】 *Select ScreentiTvr led I trn+Change FieldUbSrlcrt Fie IdFlGerterdl Helpfialifi ur: and Ek itESCExit(CjCnpyTighit 1出片 煩El.Mir?jEi|：代tm馬" QiCr三、還有一種 進入BIOS的 方法就是開機 按“F2”鍵， 通常BIOS內 容是菜單式 的。如下圖設置光驅啟動時，移動選擇菜單到“ BOO”菜單，如下圖:SETUP UTtLJTVMali】 Adwmued