船用鋁質舷梯使用說明書

1、鋁質舷梯使用說明書ACCOMMODATION LADDER INSTRUCTION 江蘇神力船舶設備有限責任公司文檔可自由編輯打印一、概況和用途 GENERAL AND USING1、 本廠按ISO5488-79造船舷梯設計生產的12-56級,經“ZC”、“NK”、“GL” 、“CCS”、“BV”認可的各種規格船用鋁質舷梯及引航員舷梯系列產品，是專供船舶工作人員及旅客上下船的專用設備，安裝于船的左右舷。THE PRODUCTION (FROM 12 DEGREE TO 56 DEGREE)OF ACCOMMODATION LADDER & ACCOMMODATION PILOT LADDER,

2、WINCH HAS BEEN CERTIFIED BY “ZC”、“NK” 、“GL” 、“CCS”、“BV”,IS DESIGNED AS PRE ISO5488-79SHIPBUILDINGLADDER,IT IS DESIGNED FOR BOTH CREWS AND PASSENGERS GO UP AND DOWN THE SHIP.IT IS FITTED AT LEFT SIDE AND RIGHT SIDE OF VESSEL.2、 鋁質舷梯及引航員舷梯踏步為固定弧形型式，行走表面設有防滑槽，舷梯及引航員舷梯全部用鋁鎂合金型材整體焊接成形，使舷梯及引航員舷梯具有重量輕、強度好、

3、使用維修方便等優點。MARINE LADDER STEP IS FIXED WITH SLIPPROOF GROOVE,THE ACCOMMODATION LADDER & PILOT LADDER IS WELD ADOPTING ALUMINIUMMAGNESIUM ALLOY,AND GALVANIZED STEEL. WITH THE FEATURE AS LIGHT WEIGHT, WELL STENGTH, AND CONVENICE FOR USE AND PRESERVION.3、 舷梯及引航員舷梯總裝后，采用整梯陽極氧化處理，提高舷梯的抗腐能力。AFTER THE ACCOM

4、MODATION LADDER & PILOT LADDER TOTAL FITTED, IT SHOULD BE ANODIE OXIDATION TREATED ON THE INTEGRAL WITH ANTICORROSION CHARACTIES.4、 各種系列規格舷梯及引航員舷梯相應配備CB*3141-83A翻梯裝置，便于舷梯及引航員舷梯的翻梯和收放，使用安全，操作方便可靠。TURING ACCOMMODATION LADDER & PILOT LADDER IN ACCODANCE WITH CB*3141-83A BE PROVOIDED FOR ALL VARIOUS ACC

5、OMMODATION LADDER & PILOT LADDER,IT CONVERIENCE FOR HOISTING OF LOWERING THE LADDER ,WITH SAFETY AND EASY TO OPERATE.5、 本舷梯及引航員舷梯各項技術性能符合標準規定的設計要求和船規要求，強度分別達到和超過國際標準ISO5488-1979造船舷梯規定的要求。產品按照固定踏步鋁質舷梯GB標準的施工圖進行生產制造。ALL VARIOUS TECHNOLOGY CHARETIES OF THE ACCOMMODATION LADDER & PILOT LADDER ARE ACCOED

6、ANCE WITH THE STANDRADIZE DESIGN REQUIREMENT AND SHIPBULIDING SHIPBLATED REQUIREMENT. THE STRENGTH INDIVIDULLY REACH TO OR EXCEED THE ADVANCED WORLD LEVEL ISO5488-1979 SHOULD BE MANUFAETURED AS PER WORKING DRQWING OFFIXED GANGWAY MARINE LADDEROF GB STANDARD。二、 操作方法OPERATION METHOD翻梯操作：TURNING LADDER

7、 OPERATION1、 先將拉緊固定裝置處的翼形螺母松開，然后將固緊鉤與梯架孔脫開。FIRST LOOSEN THE AEROFOIL SCREW WHERE THE TIGHT FIXED INSTALLION，THEN SEPREATED THE FIRM LOOK FROM FROM THE LADDER FRAME HOLE 。2、 啟動絞車，舷梯依靠自身的重量，使舷梯或引航員舷梯及翻梯吊臂離開舷墻向舷外轉動，當?shù)醣坜D(zhuǎn)動到與吊臂支撐座擱平時（即水平位置時）就停止轉動，此時，舷梯或引航員舷梯已全部倒出舷外呈水平狀態，舷梯或引航員舷梯離開吊臂開始下降，舷梯下降離開吊臂約1.5高度時，絞車

8、停止工作。STARTING THE WINCH， DEPENDS ON THE WEIGHT ITSELF，ACCOMMODATION LADDER & PILOT LADDER CAUSES HANGER TO LEAVE THE BULWARK AND REVOLVE OUTWARD ROUND ITS AXIS，THE HANGER STOPS WHEN IT REVOLVES TO THE LEVEL POSITION WITH THE SUPPORT SEAT，THE LADDER HAS ALREADY BEYOND THE GUNWALE AND BECOME LEVEL POS

9、ITION，THEN THE LADDER LEAVES THE HANGER AND DESCENTS，WHILE IT LEAVES ABOUT 1.5M FROM THE HANGER，THE WINCH STOP WORKING。3、 工作人員將上平臺欄桿、舷梯扶手、中間欄索、安全網安裝好，按使用要求調整下平臺角度，安裝好下平臺欄桿柱及欄索。THE WORKERS INSTALL THE RAILS OF TOP PLATEFORM 、THE MIDEST CHAIN、THE ARMREST AND THE SAFTEY NET，ADJUST THE APPILED ANGLEOF L

10、OWER PLATEFORM，ACCORDANCE WITH REQUIREMENT，THEN INSTALL THE RAILS OF LOWER PLATFORM AND CHAIN。4、 工作人員離開舷梯或引航員舷梯，再次啟動絞車，將舷梯下降至所需用的位置時，絞車停車工作。THE WORKERS LEVAE THE ACCOMMODATION LADDER & PILOT LADDER，START THE WINCH，WHEN THE LADDER DESCENT TO THE POSITION REQUIRED，STOP THE WINCH。收梯操作：STORING LADDER OP

11、ERATION1、 啟動絞車，將舷梯或引航員舷梯上升至離翻梯架約1.5m高度時，停止工作。STARTING THE WINCH，WHEN THE ACCOMMODATION LADDER & PILOT LADDER REACHES UP TO THE 1.5M HIGHT AWAY FROM THE TURING LADDER DEVIES，STOP THE WINCH。2、 工作人員將安全網、中間欄索、上平臺欄桿柱、下平臺欄桿柱收裝好，放倒舷梯扶手，插好插銷，將下平臺調整至與舷梯或引航員舷梯同一水平位置。THE WORKERS STORE ALL OF THE RAILS ，THE SAF

12、TEY NET AND THE MIDEST CHAIN，PUT DOWN THE ARMREST，ADJUST THE LOWER PLATFORM TO THE HORIZONTAL STORE POSITION。3、 工作人員離開舷梯或引航員舷梯，啟動絞車，舷梯上升，當固定在梯架上的橡膠碰墊上升至與吊臂相碰時，絞車停止工作，切斷電源。THE WORKS LEAVE THE ACCOMMODATION LADDER & PILOT LADDER，START THE WINCH TO RISE THE LADDER，WHEN THE RUBBER SEAT COLLID TO THE HAN

13、GER，STOP THE WINCH AND CUT OFF THE POWER。4、 將固緊鉤與梯架固定好，收緊翼形螺母緊固梯架。FIX THE LASHING HOOK WITH HOOKED PLATE OF THE LADDER，TIGHT THE AEROROIL SCREW AND FRAME OF LADDER。三、 維護保養及安全檢查AINITENANCE SAFE OPERATION1、 舷梯或引航員舷梯及翻梯裝置必須專人負責，定期檢查，保證處于正常工作狀態。SOMEONE MUST BE PUT IN CHARGE OF THE ACCOMMODATION LADDER & PILOT LADDER AND THE TURNING LADDER DEVICE TO GUARANTCE IT IS FUNCATIONING MORMALLY REGULAR CHEEK UP MUST BE DONE。2、 所有轉動部位和轉動部位設置的油杯，要保持清潔，在舷梯或引航員舷梯使用前和使用結束后要各加一次潤滑油。KEEP ALL TURNING PARTS AND NIPPLE OF TURNING PART CLEAN，ADD THE LUBRICATING OIL SEPARATLY IN START AND END OF USING3、 為防海水銹蝕，鋼索要定期檢