塑料件卡扣等設計標準模塊自創推薦新人學習演示文稿

塑料件卡扣等設計標準模塊自創推薦新人學習演示文稿當前第1頁\共有33頁\編于星期六\23點優選塑料件卡扣等設計標準模塊自創推薦新人學習當前第2頁\共有33頁\編于星期六\23點3目錄1.柱位結構······································································3

優缺點及使用范圍······················································42.螺釘沉孔·······································································5

優缺點及使用范圍·······················································63.

帶罩蓋的螺釘沉孔····························································7

罩蓋········································································8

優缺點及使用范圍·······················································94.金屬卡口支撐臺（單邊卡位）··············································10

雙邊卡位··································································11

金屬卡口··································································12

優缺點及使用范圍·······················································135.椅背板鋼絲卡·································································14

優缺點及使用范圍·······················································156.鋼絲卡··········································································16

優缺點及使用范圍·······················································177.平板卡口連接··································································18

結構分析··································································19

優缺點及使用范圍·······················································208.卡口連接與翻邊·······························································21

結構分析··································································22

優缺點及使用范圍·······················································239.插片式卡口連接·······························································24

結構分析·································································25

優缺點及使用范圍······················································2610.圣誕樹支撐···································································27

優缺點及使用范圍·····················································28

圣誕樹例樣······························································2911.塑料支腳·····································································33

優缺點及使用范圍······················································34

當前第3頁\共有33頁\編于星期六\23點4柱位的設計方式-自攻螺釘自攻螺釘規格（國標）螺釘柱內徑?（mm）nd螺釘柱外徑（mm）wdST2.21.75ST2.92.36ST3.52.87ST4.23.47.5ST4.83.88ST5.54.49自攻螺釘?shù)臉?biāo)準尺寸表內值為參考值，一般柱位內徑較nd大0.3~0.4mm，柱位壁厚在1.25mm左右，以防止產品表面縮凹。柱位高一般在5～10mm。當前第4頁\共有33頁\編于星期六\23點5柱位結構的優缺點及適用范圍用途：將零部件（開關盒，鉸鏈等）固定到塑料件上。優點：結構簡單，固定牢固。缺點：產品表面容易縮凹，裝配工序較煩。適用產品：旁側板等需要固定零部件的塑料件。當前第5頁\共有33頁\編于星期六\23點6DB_PART_NOOS_PART_NAMEstdKdkI

1ST2.22.21.646.52ST2.92.92.45.69.53ST3.53.52.679.54ST4.24.23.189.55ST4.84.83.79.5136ST5.55.541113螺釘沉孔自攻螺釘?shù)臉?biāo)準尺寸std為螺釘螺紋處直徑；K為螺釘頭部厚度；dk為螺釘頭部直徑；l為螺釘螺紋處長度；t為產品壁厚；Δ根據公差要求進行設定。當前第6頁\共有33頁\編于星期六\23點7螺釘沉孔的優缺點及適用范圍用途：用螺絲固定塑料件。優點：裝配簡單,可拆卸,定位性好。缺點：裝配位可見，容易粘定模導致產品拉壞。適用產品：適用于大部分塑料件的非可見區，如設在可見區，必須得到客戶同意。粘定模對策當前第7頁\共有33頁\編于星期六\23點8帶罩蓋的螺釘沉孔H<1.5D,定模側壁脫模斜度大于5度。此標準件為裝配件，裝配后蓋子與本體要求無間隙、晃動、斷差，且紋理一致。當前第8頁\共有33頁\編于星期六\23點9罩蓋當前第9頁\共有33頁\編于星期六\23點10帶罩蓋的螺釘沉孔的優缺點及適用范圍用途：用螺絲固定塑料件,并遮蓋孔位。優點：裝配簡單,可拆卸,定位性好，看不到螺釘。缺點：容易粘定模導致產品拉壞，多一道裝配工序，表面有縫隙。適用產品：適用于大部分塑料件一般要求外觀面，使用時必須得到客戶同意。當前第10頁\共有33頁\編于星期六\23點11金屬卡扣支撐臺（單邊卡位）h=H-6.5(當H<=20時)；

h=0(當20<H<=30時);h=13.8(當30<H時)。當前第11頁\共有33頁\編于星期六\23點12金屬卡扣支撐臺（雙邊卡位）單邊卡位受法向力時金屬卡扣可能歪斜。雙邊卡位受法向力時金屬卡扣可能會拉斷塑料件。當前第12頁\共有33頁\編于星期六\23點13金屬卡扣可拆卸式卡扣不可拆卸式卡扣當前第13頁\共有33頁\編于星期六\23點14金屬卡扣支撐臺的優缺點及使用范圍用途：裝配CLIP后使塑料件固定在金屬板上。優點：裝配簡單，可承受法向拉力及壓力，高度調節范圍大。缺點：裝配后有一定晃動量，對切向受力抵抗弱。適用產品：旁側板、前擋板等塑料件，位置較自由。當前第14頁\共有33頁\編于星期六\23點15椅背板鋼絲卡扣詳細請參照?qǐng)D紙其他規格鋼絲可參照此形狀適當更改。H值一般在20mm左右。當前第15頁\共有33頁\編于星期六\23點16椅背板鋼絲卡扣的優缺點及適用范圍用途：用鋼絲固定塑料件。優點：裝配簡單,可拆卸,位置可適當調節。缺點：定位差，需靠其他定位機構輔助。適用產品：椅背板上端，一般于左右上角設2處。當前第16頁\共有33頁\編于星期六\23點17鋼絲卡扣其他規格鋼絲可參照此形狀適當更改，開口尺寸在鋼絲直徑的60％左右。當前第17頁\共有33頁\編于星期六\23點18鋼絲卡扣的優缺點及適用范圍用途：用鋼絲固定塑料件。優點：裝配簡單,可拆卸,模具上易實現。缺點：高度有限制,受力有脫落可能。適用產品：旁側板、前擋板等塑料件，卡扣周圍50mm左右范圍內無發泡或面套擠壓。當前第18頁\共有33頁\編于星期六\23點19平板卡扣連接當前第19頁\共有33頁\編于星期六\23點20平板卡扣連接－－結構分析當前第20頁\共有33頁\編于星期六\23點21平板卡扣連接的優缺點及適用范圍用途：平板件與其他塑料件利用卡扣連接。優點：裝配簡單且牢固，適用性強。缺點：需要其他結構支撐板件。適用產品：適用于板件與一般塑料件的連接等，板件一般不屬于重要外觀件。當前第21頁\共有33頁\編于星期六\23點22卡扣連接與翻邊當前第22頁\共有33頁\編于星期六\23點23卡扣連接與翻邊－－結構分析當前第23頁\共有33頁\編于星期六\23點24卡扣連接與翻邊的優缺點及適用范圍用途：塑料件之間的相互固定。優點：裝配簡單且牢固，適用性強，對內部結構起到遮蔽作用。缺點：受法向拉力有限，翻邊易損。適用產品：適用于各種塑料件的相互固定，例如外側飾板與內側飾板的連接、扶手盒的結合等。當前第24頁\共有33頁\編于星期六\23點25插片式卡扣連接當前第25頁\共有33頁\編于星期六\23點26插片式卡扣連接－－結構分析當前第26頁\共有33頁\編于星期六\23點27卡扣連接與翻邊的優缺點及適用范圍用途：塑料件之間的相互固定。優點：結構簡單,裝配容易，空間占用小。缺點：受力易脫落，需和其他卡扣配合使用。適用產品：例如外側飾板與內側飾板的連接等。當前第27頁\共有33頁\編于星期六\23點28圣誕樹支撐臺圣誕樹當前第28頁\共有33頁\編于星期六\23點29圣誕樹支撐臺的優缺點及適用范圍用途：利用圣誕樹來防止外表面浮起(提供法向拉力)。優點：裝配簡單,可拆卸,模具上易實現。缺點：安裝后高度不穩定,對切向受力抵抗弱。適用產品：旁側板、椅背板等塑料件。當前第29頁\共有33頁\編于星期六\23點30零件號零件名稱D1D2L1L2ApplicationForcerequirement1442633W-CLIP-PLASTICW型塑料卡子

51814.32Hole:Φ9.0±0.12

Thickness:2.75mmInsert≤80N

Extraction≥334N圣誕樹例樣當前第30頁\共有33頁\編于星期六\23點31零件號零件名稱D1D2D3L1L2L3L4L5ApplicationForcerequirement1325904CB－07000－00CLIP塑料夾子

154.66.819.31.310.816.6Hole:Φ7.0+0.1

Thickness:1.5-3mmInsert≤150N

Extraction≥200N當前第31頁\共有33頁\編于星期六\23點32零件號零件名稱D1D2D3d1d2d3L1L2L3ApplicationForcerequirement1116415A-StyleXmasTreeClipA型塑料釘

3229.24863.12.81.72.75Hole:Φ7.0-7.25

Thickness:2.75±0.15mmInsert≤8LBF

60LBF≥Extract