H3C基本配置(默認路由)

1、精選文檔H3C基本配置# 進入系統視圖<H3C>sys# 配置設備名H3Csysname RouterA# 設置super(明文)密碼RouterAsuper password simple quidway# 設置super(密文)密碼RouterAsuper password cipher quidway# 啟用telnet 管理功能RouterAuser-interface vty 0 4RouterA-ui-vty0-4authentication-mode passwordRouterA-ui-vty0-4set authentication password quidwa

2、yRouterA-ui-vty0-4user privilege level 3RouterA-ui-vty0-4quitRouterAtelnet server enable# 配置端口IP 地址RouterAint e 0RouterA-Ethernet0ip add 24# 啟動端口RouterA-Ethernet0undo shutdownRouterA-Ethernet0quit# 保存,在任何視圖下<RouterA>save# 查看當前設備配置信息RouterAdisplay current-configuration# 查看Flash 中的配置

3、(相當于CISCO start-config)RouterAdisplay saved-configuration# 刪除FLASH 中的配置信息(重置設備配置)RouterAreset saved-configuration# 重新啟動設備<RouterA>reboot# 顯示系統軟件版本RouterAdisplay version# 訪問TFTP 服務器<H3C>tftp 服務器IP put|get 源文件名目的文件名<H3C>tftp put startup.cfg startup.cfg /上傳<H3C>tftp

4、 get test.txt test.txt /下載􀂄 交換機、路由器基本命令# 交換機IP 地址H3Cint vlan 1H3C-Vlan-interface1ip add 24H3C-Vlan-interface1undo ip add 24# 創建VLANH3Cvlan 10H3Cundo vlan 10# 向VLAN 添加一個、多個端口H3C-vlan10port e 1/0/1H3C-vlan10port e 1/0/5 to e 1/0/7H3C-vlan10port e 1/0/8 to e

5、1/0/9 e 1/0/11 to e 1/0/12# 顯示VLAN 信息H3Cdis vlan# 設置以太網端口的鏈路類型為TRUNKH3C-Ethernet1/0/1port link-type trunkH3C-Ethernet1/0/1port trunk permit vlan allH3C-Ethernet1/0/1port trunk pvid vlan 1# 設置以太網端口的鏈路類型為ACCESSH3C-Ethernet1/0/1port link-type accessH3C-Ethernet1/0/1port access vlan 10H3C-Ethernet1/0/1u

6、ndo port access vlan# 配置Loopback 環回接口H3Cint loopback 0H3C-Lookback0ip add 24# 靜態路由H3Cip route s 1/0H3Cundo ip route s 1/0# 默認路由H3Cip route s 1/0􀂄 缺省路由和靜態路由一、 試驗拓撲二、 試驗要求使各網絡間能相互通信，R1 和R3 使用缺省路由，指向R2；在R2 上配置靜態路由到192

7、.168.1.0 和 的子網三、 試驗步驟R1:R1ip route R2:R2ip route R2ip route R3:R3ip route 􀂄 RIPv1一、 試驗拓撲二、 試驗要求使用 RIPv1,使各子網間能正常通信三、 試驗步驟R1:R1ripR1-rip-1undo summar

8、yR1-rip-1network R1-rip-1network R2:R2ripR2-rip-1undo summaryR2-rip-1network R2-rip-1network R2-rip-1network R3:R3ripR3-rip-1undo summaryR3-rip-1network R3-rip-1network 􀂄 RIPv2一、 試驗拓撲二、 試驗要求使用 RIPv2,使各子網間能正常通信三、 試驗步驟R1:R1ripR1-rip-1version 2R1-rip-1undo summaryR1-rip-1network R1-rip-1network R2:R2ripR2-rip-1v 2R2-rip-1net R2-rip-1