出口模制作DFM報告流程

1、Side Gate 側水口側水口Pin Point Gate 細水口細水口Hot Runner (Valve) 熱流道針閥式熱流道針閥式 Submarine Gate 潛水口潛水口Tab Gate 搭底水口搭底水口Hot Runner (Pin Point) With One Drop 熱流道點進膠熱流道點進膠Hot Sprue 單咀熱流道單咀熱流道Hot Runner (Direct) Turn To Submarine Gate 熱流道轉潛水口熱流道轉潛水口Hot Runner (Direct) Turn To Banana Gate 熱流道轉蕉形水口熱流道轉蕉形水口Hot Runner

2、(Direct )熱流道熱流道直澆口直澆口4mmCAVCORP/LBefore Change更改前更改前After Change更改后更改后 The height of the green surface : (Cut material for draft angle)綠色面減膠做出模斜度時參考如下標準:高度 減膠做2 度出模斜度；減膠高度 3.06.0mm減膠做1 度出模斜度；減膠高度 6.015.0mm減膠做度出模斜度；減膠高度15.0mm減膠做度出模斜度；減膠This green area is 0 degree, suggest to Cut material on the cavit

3、y to draft1 degree.綠色面無出模斜度，建議產品減膠1度做前模出模斜度Submarine Gate With 2Points2點潛水進膠Can you accept gate cushion?水口加工余留量是否接受水口加工余留量是否接受?Add Plastic 加膠Reduce Plastic減膠Cavity Inserts前模鑲件Core Inserts后模鑲件Undercut here, suggest to change as picture show.此處倒扣，建議如圖更改EJ-Pins頂針Lifters斜頂Sliders行位Cavity Cooling 8mm前模運水

4、 8mmCore Cooling 8mm后模運水 8mmThis position need to make the inserts, but it will have the sharp steel, so we suggest to change the part.此處由于需要做前后模相插鋼料太薄建議修改產品如下圖所示！Undercut on red area, so here cannot be released by lifter, suggest to cancel the red feature.紅色面倒扣，無法用斜頂行出，建議取消The wall of plastic is to

5、o thick here, suggest to reduce plastic to improve.此處膠位太厚，建議減膠IN 1OUT 1IN 2OUT 2IN 3OUT 3IN 4OUT 4IN 5OUT 5IN 6OUT 6IN 7OUT 7IN 8OUT 8IN 9OUT 9IN 10OUT 10IN 11OUT 11IN 12OUT 12IN 13OUT 13IN 14OUT 14IN 15OUT 15IN 16OUT 16IN 17OUT 17IN 18OUT 19IN 20OUT 20IN 21OUT 21IN 22OUT 22IN 23OUT 23Customer ( (客戶

6、客戶):):UNV1Model ( (型號型號):):DPCA B73 (100906)Part Name ( (產品名稱產品名稱):):Button ( (按鈕）按鈕） Part No. ( (產品編號產品編號):):A2C53347358/A2C53347355Drawing No. ( (圖紙編號圖紙編號):):40325705 DRW 000 AE / 40325711 DRW 000 AFMaterial ( (材料名稱材料名稱):):ABS-PC/SN 57906-11 BlackShrinkage ( (縮水率縮水率):):Mold Type ( (2/3板模板模):):2 Pl

7、ateGate Type ( (入水方式入水方式):):Submarine Gate 潛水進膠潛水進膠Injection Machine ( (注塑機臺注塑機臺):):50TCavity No. ( (出模數出模數):):1+1Design ( (編制編制):):胡偉慶胡偉慶Original Date ( (制定日期制定日期):):DFM Version ( (DFM版本版本):):A4Bill Of Material:Cavity: 2343ESR 5052 HRC Core: 2343ESR 5052HRC Slider: 2343ESR 5052HRC 3 3Material Shrin

8、kage一、排位及進膠 Layout And Inlet 4 4Material Shrinkage二、P/L 位置 P/L Position 5 5Material Shrinkage三、模具結構 前模 Mold Structure Cavity 6 6Material Shrinkage四、模具結構 后模 Mold Structure Core 7 7Material Shrinkage四、模具結構 A 頂出 Mold Structure A Ejector System 8 8Material Shrinkage五、前模運水 Cavity Cooling 9 9Material Shrinkage六、后模運水 Core Cooling 1010Material Shrinkage七、曬字位置 Engraved Position 1111Material Shrinkage八、蝕紋區域 Textured Area 1212Material Shr