路由貓Routingcat

1、路由貓( Routing cat )Where are the instructions for Conexant's 0?userspanel.A ADSL cat with routing, plus a four switch, is probably a standard broadband sharing solution for many individual and student friends. But the two device drags two power lines plus two transformers It makes people u

2、nhappy, haveenough chassis behind the line goes more messySee the interface section is very clear, a power interface, telephone in/out interface, 4 RJ45 network interface.Vertical and horizontal. The front is the LEDindicator1. BriefTD2310 has high integration, stable performance, wide application r

3、ange, easy installation and dependence on host performanceLow level, fully support G.dmt full rate transmission andG.lite transmission. Menu matching based on WEB interfaceThe utility model makes the control more convenient and flexibleTD2310 provides "permanent" online functionality that

4、allows you to access the Internet at any time; voice, data, and data are transmitted simultaneouslyDoes not affect the downlink rate of 8M.ADSL, uplink up to 1M, to provide you with high-speed access, in addition to ordinaryBroadband Internet applications, TD2310 also has advanced routing features,

5、built-in RIP, NAT and other routing assistanceasDiscuss and implement advanced virtual server functionality long as you own TD2310 and your personal planThe computer will soon become a powerful WEB server2. product specificationsProduct featuresFull rate, adaptive ADSL routers support bridge modeCom

6、ply with ADSL, Forum, ANSI, IETF, ITU, UAWG and other specifications and recommendationsPlug and play, easy to operate, easy configurationPerfect and friendly user configuration interfaceYou can upgrade your system through the local PCLED indicates the working status of the ADSL line and the LANGene

7、ral characteristicsConforms to the ADSL Standard SpecificationANSI T1.413 Issue2Full rate ITU G.dmt (G.992.1) standardThe ITU G.lite (G.992.2) Regulations are not provided for separatorsYD / T11882002 standardMaximum downlink / uplink speed: 8Mbps/1MbpsSupport agreementBridged/Routed, Ethernet, over

8、, ATM (RFC1483)PPP over Ethernet (RFC2516)PPP over ATM (RFC 2364)Classical, IP, over, ATM (RFC1577)ATM Forum UNI 3.1/4.0Up to 8 VCATM SARATM AAL5OAM F4/F5Routing modeIP routing -RIP2Static routingDHCP (Dynamic Host Configuration Protocol) server and clientNAT (network address translation)NAPT (netwo

9、rk address and port conversion)ICMP (Internet control message protocol)securitySystem management is password protected, PPP user authenticationPAP (Password, Authentication, Protocol)CHAP (Challenge, Handshake, Authentication, Protocol)ETHERNET interfaceCompatible with IEEE 802.3 standards10/100Mbps

10、 automatic selectionManagement based on HTTP WebSystem firmware can be upgraded via FTPConnection statistics for WAN and LAN endsStatic route configuration and routing tableNAT/NAPT configurationPassword protected accessBridge or routing optionsPPP user identification and passwordVC configurationEnv

11、ironmental requirementsAmbient temperature: 0 - 40Relative humidity 30% - 90%Relative humidity 20% - 93%3. front panel instructionsTD2310has 8 lights at the front, which can be used to determine modulation solutions by observing their statesThe work of the regulator is normal, and each indicator lam

12、pworks from top to bottom as follows:powerPWRpower indicator and MODEMself check indicator light, up, about 5 seconds after the extinctionDestroy, start flashing after 5 secondsSYNC when the ADSL connection is successful, the indicator light will be bright, otherwise it will flickerRXD flashes when

13、downloading dataTXD uploads data will blinkWhen LAN1 is powered on, it flashes at normal work and blinks when the data is transferredWhen LAN2 is powered on, it flashes at normal work and blinks when the data is transferredWhen LAN3 is powered on, it flashes at normal work and blinks when the data i

14、s transferredWhen LAN4 is powered on, it flashes at normal work and blinks when the data is transferred4. rear panel descriptionThe interfaces from top to bottom are described below:Power interfaceThe LAN1RJ-45 interface connects network card with the network cableThe LAN2RJ-45 interface connects ne

15、twork card with the network cableThe LAN3RJ-45 interface connects network card with the network cableThe LAN4RJ-45 interface connects network card with the network cablethe user LANor the computer'sthe user LANor the computer'sthe user LANor the computer'sthe user LANor the computer'

16、sMODEM telephone line connectionPHONE telephone connection portThe RESET system restarts and restores factory values5. hardware connection(1) connect the power supply to the power interface of TD2310(2) using the distribution network cable, one end of which is connected with the LAN port of TD2310,

17、and the other end is connected with the cableComputer network card connection(3) insert the ADSLtelephone line into the MODEMinterface of TD23106. enter the Web Manager (1) enter in the IE address bar(2) system popup < enter network password > dialog boxUsername: admin (Manager)Passwo

18、rd: epicrouterUsername: user (user)Password: password7. configuration methodInto the TD2310Webbased network configuration interface, the interface configuration is divided into state, configuration,Administrator permissions three majorWhen the configuration is complete, click the submit button,and t

19、hen click "Save Settings"Deposited before it becomes effectivestateThis section includes 4 options: home, ADSL, LAN, and PPP, with the introduction of TD2310Software version, line status, and its own addressHomeShows the current version of the ADSLModemsoftware, the WAN, the IP, and the LA

20、NThe number of IP addresses and DHCP clientsADSLThe ADSLstatus item displays the current ADSLModemlink status, letterNoise ratio, line attenuation, error rate and so on. Through this table dataThe observation can determine whether the ADSLlink is good or notLANDisplays the IP Modem address, subnet m

21、ask, MAC address, and Ethernet port of ADSLThrough this table, you can look at the information about the local IP configurationPPPWhen you use the built-in PPoE or PPoA dial, you can display the dialing status and the session name, PVCLink, mode, status, send packet, receive packets and other specif

22、ic information, can determine the link accordinglyIs it in good condition?To configureNote: this section is the configuration point, and all the required parameters are herePlease read it in detailThis section includes: WAN,LAN, PPP, NAT, virtual server, DNS, bridge9 options for filtering, storing s

23、ettings, and not saving them to restartWAN configurationADSLconfiguration interface, the main configuration gateway, VPI, VCI, encapsulation protocol, networkBridge mode, group Internet management protocol, PPP and DHCPThe main options are provided as follows: 1, VCI, VPI settingsEnable VC0, set VCI

24、, VPI. (1483 bridge mode, static IP in routing mode)Mode, that is, line mode, PPPoE, that is the virtual dial-up method needs to configure this parameter2, static IP, subnet mask1483 bridge mode, PPPoE,that is, virtual dial-up access to the Internet, do not need to configure the two parameters;This

25、parameter is configured in the static IP mode of routing mode, that is, the private line mode3 gatewayThis parameter is provided by ISP (1483 bridge mode does not require this parameter; static in routing mode)The IP mode, that is, the private line mode, requires this parameter; PPPoE does not need

26、to configure this parameter4, ATMRefer to the underlying protocol for ADSL. Service types and bandwidth settings are defaults5, package formatYou can select the appropriate encapsulation method based on the parameters provided by the ADSL service provider 6 BridgeYou can change the bridge mode for P

27、PPoE, that is, virtual dial-up and dedicated Internet accessSet to Disable, only 1483 bridge mode, can be set to Enable.7, PPP (point to point communication)Fill in the username and password here, if you are connected by virtual dial-upAccording to the corresponding parameters supplied by the ADSL s

28、upplier, enter Service, Name, and UsernameAnd Password, dedicated Internet access and 1483 bridge mode, do not need to fill in this parameter8, DHCPDo you want to enable DHCP clients?,PPPoE virtual dial-up, you need to enable this feature, dedicated lineInternet access and 1483Bridge do not need to

29、enable this feature 9 、 virtual circuit Select the corresponding virtual circuit number in the option, and usually select the default value of 0LAN configurationThe main configuration is the IP address, subnet mask, and DHCP address of the ADSL ModemStart IP address and end IP address, user time, us

30、er mode, set Ethernet modeType.ADSL a small number of users (less than 10 households) do not need to configure this parameterPPP configurationYou can configure the link status of peer to peer dialing, including the VC number, send package, and receivePackets and other specific information can be use

31、d to determine link statusNAT configurationThis function is valid only in routing mode, a IP address translation function that allows specifiedThe PC address in the LAN or all the PC addresses in the LANare translated into temporaryWide area network IP address, and connect to Internet.NAT: Specifies

32、 that the address of the PC within the LAN is converted to a temporary Wan IP addressNAPT: all PC addresses in the LAN are converted to temporaryWan IP addressesThe following describes its implementation methods1., the "NAT" (this default is "Dnamic NAPT") does not need to be spe

33、cified within the domain networkAll PCcan be connected to Internet), select NAT, and configure the sessionEnter the name of the specified PC in the name, and enter the interfaceAfter the channel, click submit"2. click "return to NAT configuration", "session name", "user

34、IP" to enter the session nameNamethe namethat exists in the table and specify the IP address of the PC "Add", and finally click SubmitVirtual server configurationThe TD2310 routing function is very powerful, and the virtual server functionality is its routing functionWhat is the virtu

35、al server function? The virtual server is the public network and the insideA bridge between networks, through the port mapping, you access a specific end of the public networkBy using the TD2310mapping function, you can access a specific internal networkPort. This is more convenient for setting up y

36、our homepage. You only need a private networkIP, the computer will becomea powerful WEBserver. Here's how it worksID: no user changes are requiredPublic network port: fill in the public network IP port numberInternal network port: intranet (LAN) IP port numberPort type: port mapping protocol typ

37、eHost IP address: internal network (LAN) host addressDNS configurationHere you can select the DNS server and user configuration optionsPlease note that the following parameters need to be configured only when they are on the Internet, otherwiseYou need to configure the following parameters1, DNS ser

38、ver: select "Auto Discovery + User Configured""2, preferred DNS server: provided by ISP3, standby DNS server: provided by ISP, when the first choice failed, automatically enable standbyBridge filteringBridge filtering can filter specific MAC addresses or allow specific MAC addresses t

39、o be visitedQuery. Bridge filter defaults to not enabledAdministrator privilegesThis section includes the WAN status, the ATM state, the TCP state, the routing table, and the MACAddress table, ADSLconfiguration, RIP configuration, password configuration, mix configuration, restore default settingsSe

40、ttings, diagnosticstests, code image updates, network codeimage updates, system logs, etc.WAN stateDisplay or update the IP address, subnet mask, MAC address, virtual circuit in WanTD2310, 4Port, ADSL, Router, ManualATM stateYou can see the information in the ATM layer. In this table,you can see the

41、 number of bytes sent and receivedThe number of bytes, and errors that occur on the ATM layer,to determine whether the underlying transport is normalTCP stateView the packets sent and received by the TCP protocol, including the number of packets sent, and the packets receivedNumber, send bytes, statistical checksum, error discard package, etc.Routing tableWhen the system receives packets from the remote, the system detects its destination. The systemThe target subnet of the target IP is calculate