豪華油煙機使用說明書中英對照

1、豪華吸油煙機Luxurious Cooker Hood安裝說明Installation Instruction1、安裝工具準備，沖擊電鉆（帶鉆頭)扳手螺絲刀尺1. Prepare installation tools: Impact Electric Drill (with drill) Spanner Screwdriver Ruler2、確定位置：吸油煙機平行安裝于爐頭正上方底部距爐臺安裝參考高度650750mm,可拆卸擋板安裝參考尺寸430mm，可根據實際的安裝情況適當調整。安裝孔距機體應垂直居中和保持水平。(如煤氣爐灶安裝說明規定了較大的安裝距離者，對此應予考慮，)例：吊頂 裝飾罩 （

2、無拆卸擋板的安裝方法）吊頂 裝飾罩 可拆卸擋板 （有拆卸擋板的安裝方法）2. Determine Installation Site: the hood should be installed over the cooker. The reference setting distance from the bottom to the cooker is 650-750mm. The reference dimension of the dischargeable baffle plate is 430mm. It can be adjusted according to practical i

3、nstallation situation. The mounting hole should align vertical centers and keep horizontal with the cooker hood.(For instance, if a longer distance is stipulated in the instruction manual of cooker, it should be considered.)E.g. suspending ceiling decorative covering (installation method without dis

4、chargeable baffle plate )Suspending ceiling decorative covering dischargeable baffle plate (installation method with dischargeable baffle plate )3、安裝掛腳：按照掛腳的尺寸在墻壁的相應位置上鉆出直徑為8mm （嚴禁鉆孔過大，造成膨脹管松動而意外跌落)深度為50一60mm的四個孔，將膨脹管壓入孔內再用隨機配備的St4X40木螺釘將掛腳可靠固定。3. Install Hitching Legs: Determine the relevant positi

5、on on the wall according to the dimensions of the hitching legs. Drill 4 holes with diameter of 8mm (Do not drill holes with too large diameter to prevent accidental fall of cooker hood due to the loose of expansion pipe.) and depth of 5060 mm. Press the expansion pipe into the holes then fix the hi

6、tching legs with St4X40 wood screws accompanied with the machine.4、安裝裝飾罩：揭去裝飾罩保護膜將裝飾罩組件由上向下套入機身 。裝飾罩長度若不夠可另行向我公司購買。4. Install Decorative Covering: Disclose the protective layer of the covering and put it on the body of cooker hood from up to down. If the decorative covering is not long enough, you c

7、an purchase from our company.5、安裝機體：將機體后部的掛孔對準掛腳的按壓滑入用手晃動機體看是否掛牢。目測機體下沿應水平 。 如不平，可調整固定架之水平。5. Install the Body of Cooker Hood: Make sure the hanging holes in the back of cooker hood are directed at the hookers of the hitching legs and push the cooker hood to make the hookers slip into the holes. Sha

8、ke the cooker hood to ensure it is fastened. Estimate the lower edge by eyes, and the cooker hood should be horizontal. If not, you can adjust the mounting bracket. 6、安裝排風管：將排風管插入止回閥出風口內外圈之間，然后將排風管的另一端接至室外。6. Install Exhaust Duct: Insert the exhaust duct between inner race and outter race of the air

9、 outlet check valve. 豪華吸油煙機Luxurious Cooker Hood使用說明Operation Instruction照明 強檔 弱檔 電源Light High Speed Low Speed PowerI、電機電源開關鍵“OFF”“電源”：用來關斷油煙機電機電源1. Power Switch button “OFF” / “Power”: Press this button to cut off the power2、油煙機低速檔按鍵“”“弱檔”：控此鍵，油煙機低速運轉。2. Low Speed button “”/”Low Speed”: Press this

10、button to turn on the cooker hood at low speed3、油煙機高速檔按鍵“”“強檔”：按此鍵，油煙機高速運轉。3. High Speed button “”/”High Speed”: Press this button to turn on the cooker hood at high speed4、照明燈開關按鍵“”“照明”：按此鍵可循環開啟，關閉照明燈4. Light Switch button“”/”Light”: Press this button to turn on the light, and press again to turn i

11、t off.豪華吸油煙機Luxurious Cooker Hood電機電源開關鍵“OFF”“電源”：用來關斷油煙機電機電源Power Switch button “OFF” / “Power”: Press this button to cut off the power油煙機低速檔按鍵“”“弱檔”：控此鍵，油煙機低速運轉。Low Speed button “”/”Low Speed”: Press this button to turn on the cooker hood at low speed油煙機高速檔按鍵“”“強檔”：按此鍵，油煙機高速運轉。High Speed button “”

12、/”High Speed”: Press this button to turn on the cooker hood at high speed照明燈開關按鍵“”“照明”：按此鍵可循環開啟，關閉照明燈Light Switch button “”/”Light”: Press this button to turn on the light, and press again to turn it off.延時功能鍵控鍵“”：按此鍵，啟動延時一分鐘油煙機進入低速運轉按電源開關“”或高速鍵“”取消延時功能，延時完成后關閉所有電源。Delay button”/: Press this button

13、to activate the delay function. The cooker hood will continue to operate 1 minute at low speed. To cancel the delay function, press the Power Switch button “” or High Speed button“”. After the delay, power will be cut off automatically. 照明 上調 下調 快檔 慢檔 停止Lighten Upward Downward High Speed Low Speed S

14、top程序：上電時音樂聲按鈕時伴有蜂鳴。Application: When turning on the power, there are music sounds and when pressing buttons, there are beeps.開關程序功能：Switches Application Function:1、停止鍵和停止指示燈：停止鍵作為電機及延時總關鍵，電機不工作按此鍵無效。在電機快或慢工作時停止指示燈亮，電機不工作時停止指示燈不亮。1. Stop Button and Stop Indicator Lamp: Stop button is the master swit

15、ch of motor and delay function. If the motor does not work, pressing this button is ineffective. When the motor works with low or high speed, the stop indicator lamp is on. When the motor does not work, the stop indicator lamp is off. 2、電機快慢鍵和電機快慢鍵指示燈：當按電機快或慢鍵工作時其相應指示燈及停止，指示燈亮，快慢互鎖當電機工作時，(如：電機快檔工作時，

16、再一次按電機快檔鍵電機關機，進入電機工作等待狀態。當電機慢檔工作時，再一次按電機慢檔鍵電機關機，進入電機工作等待狀態。按停止鍵關機。停止指示燈及電機指示燈同時熄滅)。2. Motor Speed Buttons and Motor Speed Indicator Lamps: When motor works at low or high speed, the relevant indicator lamp and stop indicator lamp are on. They are interlocked. During operation (e.g. when the motor wo

17、rks at high speed, press the high speed button and then the motor is off and waiting to be operated. when the motor works at low speed, press the low speed button and then the motor is off and waiting to be operated. When pressing stop button, the stop indicator lamp and electric motor speed indicat

18、or lamps are off.)3、延時鍵及延時指示燈：延時指示燈分為上調和下調當電機工作時才能開啟按上調鍵延時，時間將從1-9往上加上調指示燈閃爍，按下調鍵延時，時間將從91往下減，下調指示燈閃爍。在調時過程中可以在1-9任何一分鐘上下調整如現調整時間為3：OO它可以上調為4：00或下調為2：00等。延時開啟時上調和下調指示燈同時亮，延時設定好后自動進入倒計時，此時按上調和下調鍵為取消延時。 (設定時間最高為9分鐘，最低1分鐘)倒計時完成后關掉電機進入電機工作等待狀態。 (注：如此時照明工作延時設定倒計時完成后只關掉電機不關照明。) 出廠時間設置為3分鐘延時具有記憶功能。3. Delay

19、 Buttons and Delay Indicator Lamps: Delay indicator lamps include upward lamp and downward lamp. They are on during the motor operation. When pressing upward delay button, time increases from 1 to 9 and the upward indicator lamp flashes. When pressing downward delay button, time decreases from 9 to

20、1 and the downward indicator lamp flashes. You can adjust time upward or downward on the basis of number between 1 and 9. For instance, if the time is 3 minutes, you can adjust upward to 4 minutes or downward to 2 minutes. When activating the delay function, upward indicator lamp and downward indica

21、tor lamp are on. The delay time counts down automatically. At this time if you press upward button or downward button, delay function will be cancelled. (The maximum setting time is 9 minutes while the minimum is 1 minutes.) After the countdown, the motor is off and waiting to be operated. (Note: af

22、ter the countdown, the motor is off but light is still on.) Factory default time is 3 minutes. The delay process has memory function. 4、照明鍵及照明指示燈：設照明鍵及照明指示燈獨立一開一關，當按一下照明按鈕時，照明指示燈亮，但是停止指示燈不亮。4. Light Switch Button and Light Indicator Lamp: Light button and light indicator lamp are independent. Press

23、once to turn on the light and press again to turn off. When press the light button once, the light indicator lamp is on but the stop indicator lamp is off. 豪華吸油煙機Luxurious Cooker Hood 1. 電機電源開關鍵“OFF”“電源”：用來關斷油煙機電機電源1. Power Switch button “OFF” / “Power”: Press this button to cut off the power2. 油煙機低

24、速檔按鍵“”“弱檔”：控此鍵，油煙機低速運轉。2. Low Speed button “”/”Low Speed”: Press this button to turn on the cooker hood at low speed3. 油煙機高速檔按鍵“”“強檔”：按此鍵，油煙機高速運轉。3. High Speed button “”/”High Speed”: Press this button to turn on the cooker hood at high speed4. 照明燈開關按鍵“”“照明”：按此鍵可循環開啟，關閉照明燈4. Light Switch button “”/”

25、Light”: Press this button to turn on the light, and press again to turn it off.5. 延時功能鍵控鍵“”：按此鍵，啟動延時一分鐘油煙機進入低速運轉按電源開關“”或高速鍵“”取消延時功能，延時完成后關閉所有電源。5. Delay button”/: Press this button to activate the delay function. The cooker hood will continue to operate 1 minute at low speed. To cancel the delay fun

26、ction, press the Power Switch button “” or High Speed button“”. After the delay, power will be cut off automatically. 照明 慢速 快速 電源Light High Speed Low Speed Power程序：通電蜂鳴器嘀聲提示，顯示屏顯示1 2：00，此時需進行北京時間的調整。Application: When turn on the power, a tick from the buzzer reminds you and on the screen is 12:00. A

27、t this time you should set it according to Beijing time. 1、按住開關鍵4秒，嘀聲提示進入北京時間調整狀態，開關按鍵燈亮、小時位閃動，按慢風鍵遞減，按快風鍵遞增小時，再按開關鍵，分鐘位閃動，按慢風鍵遞減，按快風鍵遞增分鐘，如此循環。5秒沒動作自動返回北京時間狀態。1. Press the Power button for 4 seconds, a tick reminds you to enter the Beijing time-adjusting state. The Power button lamp is on and the H

28、our begins flashing. Press the low speed button to decrease and high speed button to increase. And then press power switch button, the Minute begins flashing. Press the low speed button to decrease and high speed button to increase. If you do not press any buttons for 5 seconds, it will enter Beijin

29、g time display state automatically.2、在時間顯示狀態下按快風鍵，電機強檔啟動，按慢風健，電機弱檔啟動，兩鍵互鎖工作。在慢風狀態下按慢風鍵或在快風狀態下按快風鍵可以停止電機進入時間顯示狀態。2. In the time display state press high speed button, motor works at high speed while pressing Low Speed button, motor works at low speed. Two buttons are interlocked. If in the state of l

30、ow speed press low speed button or in the state of high speed press high speed button, the motor will be off and waiting to be operated. 3、在快風或慢風狀態下按開關鍵可進入延時狀態，時間區從2：00以秒遞減顯示倒計時，開關鍵燈閃動，顯示屏延時關標志顯示，到0：00后嘀聲提示關閉全部輸出進入時間顯示狀態。3. When the motor works at low or high speed, press power switch button to ente

31、r delay state. Time displaying on the screen counts down second by second from 2:00. The Power Switch button lamp begins flashing and the delay sign displays on the screen. When counting down to 0:00, a tick reminds all output is cut off and the cooker hood enters time display state.4、按燈開關可單獨控制照明燈輸出

32、。4. Light switch button controls the light independently. 豪華吸油煙機Luxurious Cooker Hood維護與保養Maintenance & Repair1、吸油煙機應視環境條件，定期維護清洗保持機體清潔與使用效果，延長使用壽命。建議機體內外表面在每次烹飪后都進行擦拭；為保證油煙順暢排出，過濾網視使用情況經常用溫水加清洗劑浸洗。1. The cooker hood should be maintained and cleaned regularly depending on the surrounding environment

33、 to keep its cleanness, a good effect and a longer service life. The internal and external surfaces should be cleaned after cooking. Clean the filter using warm water with washing-up liquid according to operation condition to make sure an unhindered exhausting. 2、維護保養前請您務必拔掉電源插頭以確保您的人身安全，2. Pull out

34、 the electric plug before repairing and maintaining the cooker hood to ensure your personal safety.3、清洗機殼內外表面可使用含有中性洗滌劑的溫水清洗，再用干布揩凈。切忌用清潔球之類的粗糙物件揩擦以免損傷表面?？?xí)r應帶上手套以免棱邊傷手。3. Clean all internal and external surfaces using warm water with a mild detergent, and then wipe the surfaces using a dry cloth. A

35、void using abrasive cleaning objects, e.g. steel wire ball. These will damage the surfaces. Wear gloves when cleaning surfaces to prevent your hands being hurt by seamed edges.4、當清洗葉輪、風道內部時，應特別小心，嚴禁壓擠葉輪。以免葉輪變形引起晃動增大、噪聲增加。影響吸煙效果也不可碰撞或丟棄輪上的配重片以免葉輪的動平衡性能不良。4. When cleaning the impeller and duct interio

36、r you should be careful to avoid squeezing the impeller. It may result in impeller deformation, great wobbles and noises, which have a negative exhausting effect. Do not crash or abandon the weight stack on the impeller to prevent poor balance performance of impeller.5，清洗時嚴禁電機、開關，電器盒及照明燈內部進水5. Avoid

37、 water penetrating into motor, switches, electronic box and light during cleaning. 6、清洗過濾網時，先用手托住濾網用螺絲刀擰下螺絲浸入去污力較強的清洗劑中浸泡，表面用軟刷刷洗然后用雙手把持濾網在洗滌液中上下晃動，再用清水沖洗，清洗完畢晾干后再裝回原處。一般可每周清洗一次，嚴禁用香蕉水、汽油等易燃溶劑清洗，6. During cleaning the filter, hold filter by hand and take out the screw by screwdriver. Dip it in a str

38、ong detergent and scrub the surfaces by a soft brush. Take the filter up and down in the detergent and then rinse with water. After cleaning, dry the filter before replacing it. The filter should be cleaned every week. Do not use flammable solvents such as lacquer thinner, benzene etc. 7、裝卸油杯時可將油杯按水

39、平方向向外緩緩拉出清除積油后再裝回原處7. When loading and discharging the oil collector, slowly pull out the oil collector in horizontal direction. Clean oil and replace it.注意事項Cautions 1、警告：在接近接線端于前，必須切斷所有的供電電路。1. Warning: before accessing to the supply terminals, you must cut off the supply circuit. 2、維護、保養吸油煙機或調換照明

40、燈時請用戶務必拔掉電源插頭以確保操作者人身安全。2. During maintaining and repairing the cooker hood or changing a light, you must pull off the electric plug to ensure the operators safety. 3、若電源線損壞，只能用本公司的專用電源線或與本公司質量相符臺的電源線更換。3. If the power line is damaged, please use the special power line from our company or the power

41、line with the same quality.4若照明燈損壞只能用同類型燈更換。4. If the light is damaged, please replace by light of the same type.5、爐火在不使用時應及時熄滅，禁止?fàn)t火直接烘烤吸油煙機。5. Switch the cooker off when you do not use it. Never use an open flame beneath the cooker hood.6、如果不按說明書規定的方法清洗，吸油煙機有起火的危險。6. If you do not clean the cooker

42、hood according to the methods stipulated in the instruction manual, it may lead to a fire hazard.7、吸油煙機排出的氣體不應排到用于排出燃燒煤氣或其他燃料的煙霧使用的熱煙道中。7. Do not discharge the smoke from cooker hood into the hot chimney duct for smoke from burning gas or other fuels.8、吸油煙機在爐灶消耗煤氣等燃料時使用，房間必須通風良好8. When using the coo

43、ker hood over a gas or other fuels cooker, the room must be well-ventilated.9、煙道口徑小于風管口徑會影響吸煙效果風管過長也會影響吸煙效果。9. If the chimney duct caliber is less than the exhaust duct caliber or the exhaust duct is too long, the exhausting effect will be influenced. 10、吸油煙機不要裝得太高也不要受外界氣流干擾，以免降低吸煙效果10. The cooker hood should not be installed too high or influenced by outside air flow to avoid the decrease of exhausting effect.11、裝機時，請使機體保持水平。11. During installation, keep the cooker hood horizontal. 1 2、電源插座必須使用可靠接地線的專用插座。12. The electric outlet must be the special outlet with reliable and effective grounded