電梯曳引機#中英文翻譯#外文翻譯匹配

英文翻譯 Traction machine As power provider for lift, traction machine, also called main machine, is composed of motor, brake, geared machine and seat. It is a drive to make car move by means of the friction between traction rope and sheave. According to whether the geared machine is provided or not, it is classified into geared and gearless types. Geared traction machine Geared traction machine is widely used in cargo lift, passenger lift and service lift with speed of not more than 2.0m/s. To reduce working noise and enhance stability, worm gear is normally used as geared drive. Such machine is composed of motor, worm, gear, brake, rope and seat, as shown is figure 2-1. Main parameters, such as lift load and speed are determined by Hp and speed of traction machine, worm and gear numbers, gear ratio, diameter of traction machine, rope grooves and traction ratio (traction mode). For lifts adopting geared traction machine, the relationship between lift speed, traction gear ratio, traction machine diameter, traction motor speed is as follows: Where: v lift speed （ m/s） D diameter of traction machine（ m） N motor speed (r/min) y traction ratio（ traction mode） j gear ratio For example: Given the fact that sheave diameter of traction sheave is 0.8m, motor speed is 1500r/min, reduction ratio is 53:3, gear ratio is 2:1, what is lift speed? D=0.8m， N=1000r/min, y=2/1, j=53/3 From the given conditions, we learn that D=0.8m， N=1000r/min, y=2/1, j=53/3. According to above mentioned formula, we can calculate that： As power provider for lift movement, traction s/75m.1353126014800 . 814.360 jy ii D Nvmachine features complicated operation procedures, among which is involved with frequent start-up, brake, clockwise and counterclockwise rotation. Due to constantly changing load, working status of traction machine is characteristic of repetitious short time operation, electrical control and regeneration. Therefore, with low start-up current, large start-up torque, mechanically rigid features and low noise, it is required that traction machine should not only be adapted for frequent start-up, brake, but also start up and function well when power oltage fluctuates within normal range. Being special machine for lift, traction machine is characteristic of complicated operation, whose Hp can be calculated through following formula: Where: P shaft Hp of traction machine (kw) G rated load of car (kg) offsetting coefficient total mechanical efficiency v lift speed（ m/s） For lift with geared traction machine, if worm gear is Archimedes type, total mechanical efficiency ranges from 0.5 to 0.55; for lift with gearless traction machine, total mechanical efficiency ranges from 0.75 to 0.8. For example: For an AC two-speed lift whose rated load is 2000kg and rated speed is 0.5m/s, worm gear is Archimedes type, rated speed of motor is 960r/min, what is hp of motor? According to G = 2000kg, = 0.5， v = 0.5m/s， = 0.5, we can calculate by inputting given values. Geared traction machine is classified into AC and DC types. W191 traction machine is AC frequency-variable motor. Currently, besides worm geared machine, bevel and star geared machines are also available. Gearless traction machine 9 .8 k w0 .51 0 2 0 .50 .5 )(12 0 0 01 0 2 ) vG ( 1P Gearless traction machine is used in lifts with speed of more than 2.0m/s. With traction sheave fixed in motor shaft, this traction machine is simple in structure without any mechanical geared machine. Specially designed for manufactured for lift, traction motor is suitable for lift operation and classified into speed-variable DC and frequency-variable AC motor. In figure 2-2 is shown an AC frequency-variable gearless traction machine. This machine needs much more brake torque than geared machine when it is manufactured, therefore, it needs a rather bigger brake. Gearless traction machine is more often than not used in compound winding drive, therefore, force applied on traction sheave, compound winding sheave and bear is much larger than that on traction machine; corresponding shaft is of longer diameter. With no geared machine, it has longer usage life. Permanent magnet synchronous gearless traction machine We cant help mentioning the application of permanent magnet synchronous gearless traction machine in lift. With the rapid development of traction technology in lift, more and more lifts without machine room are adopting permanent magnet synchronous gearless trailing technology. For lifts without machine room, there is no need to enlarge well dimensions, simplifying and beautifying construction, saving cost, especially the application value of such lifts is enhanced by 圖 2 -2 無齒輪曳引機 DAF290 Figure 2-2 Gearless traction machine DAF Brake Motor Traction sheave low noise, high efficiency and power economization, and what distinguishes lifts without machine room from others lies in the permanent magnet synchronous gearless traction machine. In figure 2-3 is shown PMS425AL permanent magnet synchronous gearless traction machine used in Thyssens lifts without machine room. The traction machine is flat in structure, so only a very small space is needed between well walls and car to complete installation. With gearless design , motor torque directly passes on to traction sheave, combined with static friction of non-deceleration part, driving efficiency can exceed 90%; besides, due to low rotation speed, traction machine runs with low noise and is free from vibration. The traction machine has two mechano-electronic brakes, therefore, the other brake can provide sufficient jerk force to stop car with 100% rated load if one brake fails to function. Characteristics of permanent magnet synchronous gearless traction machine: Comfortable riding; Low running noise; High efficiency; Low load of electrical devices; Convenient and reliable maintenance, without need to change oil, eliminating oil leakage; Easy to replace assembly, with exterior brake; Wide range of setting and installation in traction machine. Composed of springs, brake block with liner, brake arm and magnet-iron, magnetic brake is most frequently used in traction machine, as shown in figure 2-4 . When magnetic coil is power on, brake will release; when magnetic coil is power off, brake block will produce torque, relying on springs pressed tightly on brake gear. Brake function Brake has two functions: In case of power cut-off, brake can make lift stop automatically. When brake engages, deceleration of lift should not exceed that produced by overspeed governor or needed to stop car on buffer. If lift is in normal operation with speed of more than 1m/s, lift is usually decelerated through electrical control before mechanical brake engages. When lift stops moving, brake should guarantee that lift remains stationary under 125%150% rated load. Brake does not release until lift starts moving. Characteristic of brake When lift runs, i.e. motor is power-on, brake will release; when lift stops, i.e. motor is power-off, brake will engage. Mounting position For geared lift, brake is mounted between motor and geared machine (see figure2-5), i.e. on high-speed shaft. Small brake torque is needed by high-speed shaft, so that brake dimensions can be reduced. Gearless traction machine adopts adapter, i.e. is adaptor disk etween motor and geared machine, as shown in figure 2-6. Brake gear is arranged on worm gear side instead of on motor side, to ensure that lift can also stop in case of ruptured adapter. Cast into one with traction rope, brake gear of gearless traction machine is directly mounted on traction machine shaft. As a main safety part of lift system, brake has an direct impact on comfortable ride and accurate leveling. During lift operation, to achieve comfortable ride and accurate leveling, such factors can be adjusted as brake release time, brake release time and brake torque size. To reduce brake engage, release time and noise, it is required the gap between two magnets in coils be proper rather than too wide. The smaller the gap between brake block and gear is, the better. Brake block should not touch rotating gear after brake releases. Traction sheave Traction sheave is shown in figure 2-7. Geared traction sheave is located on side of geared machine. Operators stand on the shaft side of motor, facing motor. Left-placed traction machine is the one with sheave on the left of geared machine; while right-placed traction machine is the one with sheave on the right of geared machine, as shown in figure 2-8. Traction sheave of gearless traction is directly connected with motor. Traction machine suport Soldered by cast iron or secion iron with steel board, traction machine support is a seat that connects motor, brake and geared machine. Parts of tractrion machine are mounted on the support, facilating transportaion, installation and adjustment. When lift is installed, the support will be fastened on two parallel H-stell beams with designated specification that serve to bear weight. Main performance and application requirement of traction machine Take geared traction for instance, we will give a briefing on typical requirement. Traction sheave diameter D should be more than 40d (d is diameter of traction rope) Traction sheave diameter Where: D Traction sheave diameter in mm vs Traction rope rated speed in m/s i Gear ratio n Motor rated speed in r/min Fore example: Given the fact that traction ratio is 1:1, rated speed is 1.75m/s, I = 25:1, n=1326r/min, rope diameter is 13mm, what is diameter of traction sheave? Given the fact that i = 25 1， n=1326 r/min, Traction ratio is 1/1, therefore, lift rated speed is traction rope rated speed vs= 1.75m/s, Fill in the formula 2-3 with these values, Traction rope diameter d = 13mm, so 40d = 1340=520mm Obviously, 630520mm Since 630mm traction machine diameter meets D40d, a conclusion can be drawn that traction machine diameter can be 630mm. Reliable traction brake When lift is moving upwards, offsetting coefficient should be 40% of car weight plus 150% rated load. During 10-minute travel, no slipping should occur between brake gear and brake block. Given the fact that conditions stated in 2-7-2 is met, the minimum engage voltage of brake and 6 3 0 m m132614.3 2575.160000106 4 n ivD smaximum release voltage should be 80% and 55% lower than rated voltage of magnet respectively; time delay of brake engage should not exceed 0.8s. Brake blocks should be mounted in two groups; if either of them does not work, brake can still obtain sufficient brake force to make car with rated load decelerate. When traction machine is running with empty load at high speed, dB(A) surface value measured (mean value of values measured 1 meter from the top, front, left and right of traction machine respectively) should not exceed 67db(A). When traction machine is running with 2040% of rated load, valid value of retortion shocking speed of output shaft should be less than 1mm/s. Traction machine should be inspected in factory prior to shipment. Power-on continuity should be 40% in inspection, clockwise and counter clockwise rotation with empty load should run well, with cycling time not less than 3 min, travel lasting 2 hours. Working conditions of traction machine: Sea level should not exceed 1000 meters. Temperature of machine room should remain at 540 . Monthly ambient relative humidity should not more than 90%, meanwhile minimum average temperature should not exceed 25 . Deviation between voltage supply fluctuation and rated voltage should not exceed 7%. Ambient air should not contain corrosive and inflammable air. Neither lubricant nor other substances should be applied on traction rope. Quality of car and counterweight as well as the angle of traction rope should meet formula 1-1 in 1-3-4-1. For V groove, For semicircular groove or groove with cut, Where: Friction coefficient of traction rope in groove; Tangent angle of groove with cut or semi circular groove， =0 (see figure 2-7). Angle of V-groove on traction sheave (see figure 2-7). Friction coefficient between traction rope and sheave， = 0.09 中文譯文 電梯曳引機 曳引機是電梯的動力源（又稱主機） ，通常由電動機、制動器、減速機和底座組成；是靠曳引鋼絲繩與曳引輪的摩擦來實現轎廂運行的驅動機。曳引機又以電動機與曳引輪之間有無減速機區分為有齒輪曳引機和無齒輪曳引機兩種。 2-1有齒輪曳引機 有齒輪曳引機廣泛用于運行速 度 v 2.0m/s 的各種貨梯、客梯、雜物梯。為了減小曳引機運行時的噪音和提高平穩性，一般采用蝸輪副作減速傳動裝置。 這種曳引機主要由曳引電動機、蝸輪、蝸桿、制動器、曳引繩輪、機座等構成，其外形如圖 2-1。 電梯的載荷、運行速度等主要參數取決于曳引機的電機功率和轉速，蝸輪與蝸桿的模數和減速比 ，曳引輪的直徑和繩槽數，以及曳引比（曳引方式）等。 采用有齒輪曳引機的電梯，其運行速度與曳引機的減速比、曳引輪直徑、曳引比、曳引電動機的轉速之間的關系可用以下公式表示： 式中： v 電梯的運行速度（ m/s） D 曳引繩輪直徑（ m） N 曳引電動機轉速 (r/min) y 曳引比（曳引方式 ） j 減速比 例： : 由一臺電梯，其曳引輪的繩輪直徑為 0.8m，電動機轉速 1500r/min，減速比為 533 ，曳引比為 21 ，求電梯的運行速度？ 解：已知 D=0.8m， N=1000r/min, y=2/1, j=53/3 代入式 2-1得： 曳引電動機是驅動 電梯上下運動的動力源，其運行工況比較復雜。運行過程中需頻繁的起動、制動、正轉、反轉，而且負載變化很大，經常工作在重復短時狀態、電動狀態、再生制動狀態的情況下。因 此，要求曳引電機不但應能適應頻繁起、制動的要求，而且起動電流小，起動力矩大，機械特性硬，噪聲小，當供電電壓在標準波動范圍內變化時，還能正常起動和運行。因此電梯用曳引電動機是專用電機。由于曳引電動機的工作情況比較復雜，所以對電機功率的計算比較麻煩，一般常用以下公式計算： 式中： P 曳引電機軸功率 (kw) G 電梯轎廂額定載重量 (kg) 電梯平衡系數 電梯的機械總效率 v 電梯的運行速度（ m/s） s/75m.1353126014800 . 814.360 jy ii D Nv 采用有齒輪曳引機的電梯，若蝸輪副為阿基米德齒形時，電梯機械總效率取 0.5 0.55；采用無齒輪曳引機的電梯，電梯機械總效率取 0.75 0.8。 例：有一臺額定載重量為 2000kg，額定運行速度為 0.5m/s的交流雙速電梯，曳引機的蝸輪副采用阿基米德齒形，電動機的額定轉速為 960r/min，求電機的功率應為多少（ kw） ? 解：已知：，代入式 2-2得： 有齒輪曳引機的電機有交流的也有直流的。 W191曳引機的電機為交流變頻電動機。目前，除渦輪蝸桿減速機外，還有斜齒輪傳動和行星齒輪傳動兩種形式的減速機。 2-2 無齒輪曳引機 無齒輪曳引機用于運行速度 v 2.0m/s的高速電梯上。這種曳引機的曳引輪緊固在曳引電動機軸上，沒有機械減速裝置，整機結構比較簡單。曳引電動機是專為電梯設計和制造的，能適應電梯運行工作特點，具有良好調速性能的直流電動機或交流變頻電動機。 圖 2-2所示為交流變頻無齒輪曳引機。 圖 2 -2 無齒輪曳引機 DAF290 制動器 電動機 曳引輪 9 .8 k w0 .51 0 2 0 .50 .5 )(12 0 0 01 0 2 ) vG ( 1P 該曳引機制造時所需要的制動力矩要比有齒輪曳引機大得多，因此相應的制動器比較 大。由于無齒輪曳引機多數情況是用于復繞傳動結構中，所以曳引輪軸、復繞輪軸及其軸承的受力要比有齒輪曳引機大得多，相應的軸也顯得粗大。 由于無齒輪曳引機沒有減速機，所以使用壽命比較長。 2-3永磁同步無齒輪曳引機 在這里尤其值得提到的是永磁同步無齒輪曳引機在電梯上的應用。隨著電梯曳引技術的 飛速發展，采用永磁同步無齒輪拖動技術的無機房電梯正越來越多地走進電梯市場。由 于無機房電梯無需設置機房，也無需加大井道尺寸，從而可以簡化建筑設計，美化建筑 造型，節約建筑成本，尤其是無機房電梯噪聲低、效率高、節能明顯更提高 了無機房電 梯的使用價值。而無機房電梯最突出的設計就是永磁同步無齒輪曳引機。 圖 2-3 所示的是蒂森無機房電梯所采用的 PMS425AL型永磁同步無齒輪曳引機。它的扁平結構設計使得在井道壁和轎廂之間只需要一個很小的空間即可完成安裝。由于它的無齒輪設計，電動機力矩直接傳遞到曳引輪上，再加上無減速部分的靜摩擦，使得傳動效率可達 90%以上，還由于它具有很低的運轉速度，使得機器在運行過程中噪聲很低，也不會產生振動。此類曳引機采用兩組機 電式制動器，如果其中一組制動器不起作用，另一組制動器能夠提供足夠的制動力使?jié)M載下行 的轎廂停止。 永磁同步無齒輪曳引機的特點是： 乘坐舒適感好； 運行噪聲低； 效率高； 安裝電氣載荷低； 維護方便可靠，無需換油，不存在油泄露； 采用外部制動器，便于裝配更換； 曳引機設置和安裝范圍廣泛。 2-4曳引機制動器（抱閘） Brake 曳引機制動器最常用的是電磁式制動器，它由一組彈簧、帶有制動襯墊的制動閘瓦、制動臂以及電磁鐵組成，如圖 2-4 所示。當電磁線圈通電時，制動器松閘；當電磁線圈失電，制動閘瓦靠彈簧壓緊于制動輪而產生制動力矩。 2-4-1 制動器的作用 制動器的作用有以下兩條： 2-4-1-1能夠使運行中的電梯在切斷電源時自動把電梯轎廂掣停住。制動時，電梯的減速度不應大于限速器動作做產生的或轎廂停止在緩沖器上所產生的減速度。 電梯正常使用時，電梯速度 v 1m/s 的，一般都是在電梯通過電氣控制使其減速停止，然后再機械抱閘。 2-4-1-2電梯停止運行時，制動器應能保證在 125% 150%的額定負載下，電梯保持靜止、位置不變，直到工作時才松閘。 2-4-2 制動器的工作特點 制動器 的工作特點是，電梯運行即電動 機通電時制動器松閘，電梯停止運行即 電動機失電時抱閘。 2-4-3 安裝位置 對于有齒輪電梯，制動器裝在電動機和 減速機之間 （見圖 2-5） ，即裝在高轉速 軸上。因為高轉速軸上所需的制動力矩小，這 樣可以減小制動器尺寸。 有齒輪曳引機采用帶制動輪的聯軸器，即制動 器的制動輪就是電動機和減速機之間的聯軸器原盤，如圖 2-6所示。制動輪裝在蝸桿一側，不能裝在電動機一側，以保證聯軸器破斷時，電梯仍能掣停。 無齒輪曳引機的制動輪與曳引繩輪是鑄成一體的，并直接安裝在曳引電動機軸上。制 動器是電梯機械系統的主要安全部件之一，而且直接影響電梯的乘坐舒適感和平層準確