【英國標(biāo)準(zhǔn)word原稿】BS EN 1315-2-1997 尺寸分類.軟木原木.doc

豆丁網(wǎng)：/kmust1british standarddimensional classification part 2. softwood round timberthe european standard en 1315-2 : 1997 has the status of abritish standardics 79.040| bs en1315-2 : 1997|第 13 頁 共 13 頁豆丁網(wǎng)：/kmust1|no copying without bsi permission except as permitted by copyright lawbs en 1315-2 : 1997national forewordthis british standard is the english language version of en 1315-2 : 1997.the uk participation in its preparation was entrusted by technical committee b/543, round and sawn timber, to technical subcommittee b/543/4, round timber, which has the responsibility to: aid enquirers to understand the text; present to the responsible european committee any enquiries on the interpretation, or proposals for change, and keep the uk interests informed; monitor related international and european developments and promulgate them in the uk.a list of organizations represented on this committee can be obtained on request to its secretary.cross-referencesthe british standards which implement international or european publications referred to in this document may be found in the bsi standards catalogue under the section entitled international standards correspondence index, or by using thefind facility of the bsi standards electronic catalogue.compliance with a british standard does not of itself confer immunity from legal obligations.summary of pagesthis document comprises a front cover, an inside front cover, the en title page, pages 2 to 4, an inside back cover and a back cover.amd. no.datetext affectedthis british standard, having been prepared under the direction of the engineering sector board, was published under the authority of the standards board and comes into effect on 15 december 1997bsi 1997isbn 0 580 28903 6amendments issued since publicationeuropean standarden 1315-2norme europe enneeuropa ische normaugust 1997ics 79.040descriptors: wood, sawlogs, coniferous timber, dimensions, classificationsenglish versiondimensional classification part 2: softwood round timberclassement dimensionnel partie 2: bois ronds re sineuxdimensions sortierung teil 2: nadel-rundholzthis european standard was approved by cen on 1997-07-18. cen members are bound to comply with the cen/cenelec internal regulations which stipulate the conditions for giving this european standard the status of a national standard without any alteration.up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the central secretariat or to any cen member.this european standard exists in three official versions (english, french, german). a version in any other language made by translation under the responsibility of a cen member into its own language and notified to the central secretariat has the same status as the official versions.cen members are the national standards bodies of austria, belgium, czech republic, denmark, finland, france, germany, greece, iceland, ireland, italy, luxembourg, netherlands, norway, portugal, spain, sweden, switzerland and united kingdom.ceneuropean committee for standardization comite europe en de normalisation europa isches komitee fu r normungcentral secretariat: rue de stassart 36, b-1050 brussels1997 cen all rights of exploitation in any form and by any means reserved worldwide for cen nationalmembers.ref. no. en 1315-2 : 1997 epage 2en 1315-2 : 1997forewordthis european standard has been prepared bytechnical committee cen/tc 175, round and sawncontentspagetimber, the secretariat of which is held by afnor.this standard is one of a series of standards concerning round timber (softwoods and hardwoods).the other part of this standard is:en 1315-1 : dimensional classification part 1 :hardwood round timber.1scope32normative references33definitions34dimensional classification3this european standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by february 1998, and conflicting national standards shall be withdrawnat the latest by february 1998.according to the cen/cenelec internal regulations, the national standards organizations of the following countries are bound to implement this european standard: austria, belgium, czech republic, denmark, finland, france, germany, greece, iceland, ireland, italy, luxembourg, netherlands, norway, portugal, spain, sweden, switzerland and the united kingdom.foreword 2bsi 1997page 3en 1315-2 : 19971 scopethis european standard specifies a dimensional classification for softwood being conifer roundwood for which the intended use is not known.2 normative referencesthis european standard incorporates by dated or undated reference, provisions from other publications. these normative references are cited at the appropriate places in the text and the publications are listed hereafter. for dated references, subsequent amendments to or revisions of any of these publications apply to this part of this european standard, only when incorporated in it by amendment or revision. for undated references, the latest edition of the publication referred to, applies.en 844-1round and sawn timber terminology part 1 : general common terms relating to round and sawn timberen 844-2round and sawn timber terminology part 2 : general terms relating to round timberpren 1309 : 1994round and sawn timber method of measurement of dimensions1)3 definitionsfor the purposes of this standard, the definitions in the standards en 844-1 and en 844-2 apply.4 dimensional classificationdimensional classes for softwood round timber are based on diameter under bark, measured according to pren 1309 : 1994.1)4.1 diameter classestable 1. dimensional classes according to mid-diameterdimensions in centimetrescodemid-diameterd0 3 and # 6l3 6 and # 13,5l4 13,5l : length4.2 length classes4.3 combination of mid diameter and length classesexample : l2d2b = length from 3,1 m to 6 m mid-diameter from 25 cm to 29 cm1) pr en 1309 : 1994 has been divided into two parts; part 2, still in preparation, will be applicable to round timber.bsi 1997bsi389 chiswick high roadlondonw4 4al| bsi british standards institution| bsi is the independent national body responsible for preparing british standards. it| presents the uk view on standards in europe and at the international level. it is| incorporated by royal charter.| revisions| british standards are updated by amendment or revision. users of british standards| should make sure that they possess the latest amendments or editions.| it is the constant aim of bsi to improve the quality of our products and services. we| would be grateful if anyone finding an inaccuracy or ambiguity while using this| british standard would inform the secretary of the technical committee responsible,| the identity of which can be found on the inside front cover. tel: 020 8996 9000.| fax: 020 8996 7400.| bsi offers members an individual updating service called plus which ensures that| subscribers automatically receive the latest editions of standards.| buying standards| orders for all bsi, international and foreign standards publications should be| addressed to customer services. tel: 020 8996 9001. fax: 020 8996 7001.| in response to orders for international standards, it is bsi policy to supply the bsi| implementation of those that have been published as british standards, unless| otherwise requested.| information on standards| bsi provides a wide range of information on national, european and international| standards through its library and its technical help to exporters service. various| bsi electronic information services are also available which give details on all its| products and services. contact the information centre. tel: 020 8996 7111.| fax: 020 8996 7048.| subscribing members of bsi are kept up to date with standards developments and| receive substantial discounts on the purchase price of standards. for details of| these and other benefits contact membership administration. tel: 020 8996 7002.| fax: 020 8996 7001.| copyright| copyright subsists in all bsi publicatio