實驗報告――實驗七：幀中繼配置實驗

1、實驗七：幀中繼配置n 實驗?zāi)康?、 掌握幀中繼基本概念、DLCI含義、LMI作用、靜態和動態映射區別2、 掌握幀中繼基本配置：如接口封裝、DLCI配置、LMI配置等3、 能夠?qū)欣^進行基本故障排除n 實驗要求1、 幀中繼拓?fù)渑c地址規劃；2、 幀中繼基本配置和幀中繼網云配置（如幀中繼交換表配置）3、 ospf配置4、 驗證幀中繼配置并給出配置清單n 實驗拓?fù)鋘 實驗設備（環境、軟件）路由器3個，網云一個，串口線3條。n 實驗設計到的基本概念和理論幀中繼用虛電路為面向連接的服務建立連接。DLCI的含義是數據鏈路連接標識，在源和目的設備之間標識邏輯電路的一個數值。LMI的含義是本地管理接口，是客戶

2、前端設備和幀中繼交換機之間的信令標準，負責管理設備之間的連接、維護設備之間的連接狀態。n 實驗過程和主要步驟1、 地址規劃情況設備端口子端口IP地址子網掩碼Router0（A）S2/0S2/0.1192.168.1.1255.255.255.0Router1（B）S2/0S2/0.1192.168.1.2255.255.255.0Router2（C）S2/0S2/0.1192.168.1.3255.255.255.02、 單個路由器的基本配置清單（1）路由器Router0配置RouterenableRouter#config tEnter configuration commands, one

3、 per line. End with CNTL/Z.Router(config)#interface s2/0Router(config-if)#no ip addressRouter(config-if)#encapsulation frame-relayRouter(config-if)#interface s2/0.1 multipointRouter(config-subif)#ip address 192.168.1.1 255.255.255.0Router(config-subif)#bandwidth 64Router(config-subif)#frame-relay ma

4、p ip 192.168.1.2 102 broadcastRouter(config-subif)#frame-relay map ip 192.168.1.3 103 broadcastRouter(config-subif)#exitRouter(config)#interface s2/0Router(config-if)#no shut%LINK-5-CHANGED: Interface Serial2/0, changed state to up%LINK-5-CHANGED: Interface Serial2/0.1, changed state to upRouter(con

5、fig-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0.1, changed state to up（2）路由器Router1配置RouterenableRouter#config tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#interface s2/0Rou

6、ter(config-if)#no ip addressRouter(config-if)#encapsulation frame-relayRouter(config-if)#interface s2/0.1 multipointRouter(config-subif)#ip address 192.168.1.2 255.255.255.0Router(config-subif)#bandwidth 64Router(config-subif)#frame-relay map ip 192.168.1.1 201 broadcastRouter(config-subif)#frame-re

7、lay map ip 192.168.1.3 203 broadcastRouter(config-subif)#exitRouter(config)#interface s2/0Router(config-if)#no shut%LINK-5-CHANGED: Interface Serial2/0, changed state to up%LINK-5-CHANGED: Interface Serial2/0.1, changed state to upRouter(config-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Ser

8、ial2/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0.1, changed state to up（3）路由器Router2配置RouterenableRouter#config tEnter configuration commands, one per line. End with CNTL/Z.Router(config)#interface s2/0Router(config-if)#no ip addressRouter(config-if)#encapsulation

9、 frame-relayRouter(config-if)#interface s2/0.1 multipointRouter(config-subif)#ip address 192.168.1.3 255.255.255.0Router(config-subif)#bandwidth 64Router(config-subif)#frame-relay map ip 192.168.1.1 301 broadcastRouter(config-subif)#frame-relay map ip 192.168.1.2 302 broadcastRouter(config-subif)#ex

10、itRouter(config)#interface s2/0Router(config-if)#no shut%LINK-5-CHANGED: Interface Serial2/0, changed state to up%LINK-5-CHANGED: Interface Serial2/0.1, changed state to upRouter(config-if)#%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0.1, changed state to up3、 網云交換表配置（1）Se0端口的配置：（2）Se1端口的配置（3）Se2端口的配置（4）將其進行連接：4、 驗證三個路由器通信情況（1）Router0到Router1和Route