輔助支架屈服載荷試驗

1、報告編試驗報告 ： 輔助支架屈服載荷試驗 The yield load test of assistant編制報告編試驗報告 ： 輔助支架屈服載荷試驗 The yield load test of assistant編制審核批準淅川汽車減振器廠驗?zāi)康? 對本廠試制的派力奧減振器輔助支架的屈服載荷試驗評價驗?zāi)康? 對本廠試制的派力奧減振器輔助支架的屈服載荷試驗評價為配套廠提供依據。Do evaluation of the yield load test of bracket for the front shock absorbers that we trial-produced for Pail

2、iao providetheevidenceforthe10V和轉2.5m/s=10VF-S test bench (Displacement converter50mm=10Vandtherotatespeed 2.5m/s=10V專用試驗夾具Special驗依據Test standard：Norma7-F6080 及派力奧前減振器圖StandardNorma7-F6090andthedrawingoftheshock四試驗條件Test 1圖紙是懸掛適用減振器的最新圖紙Thedrawingis2溫度3大氣壓力Atmospheric pressure：860-4相對濕度Relative hum

3、idity：45-5載荷LoadP2Fcand6頻率7把減振器固定到試H3模擬工作條件Fix sample on the fixture according to its thevehicleworkingconditions usingthetightener驗對象Testobject: 從試制的派力奧前減活塞桿產品中隨機抽取2（零件號159GZ， rods ofthevehicleworkingconditions usingthetightener驗對象Testobject: 從試制的派力奧前減活塞桿產品中隨機抽取2（零件號159GZ， rods of the shock absorbe

4、rs from the products that we trial-No.:S32-159GZ).TheNo.isNo.l,No.六method（施加增量連載荷 P 到支架變形同時 X-Y 繪圖儀中記錄力位移曲線 theincrementloadPtillthebracketdistortionandatthesametheforce-displacementcurveisrecordedbytheX-1在 0.05Hz 穩定速率下進行試驗 Do test under constantvelocity2在兩只試件上重復試驗Repeatthetest23按照數據處理表格中輸入3按照數據處理表格中輸入記錄的數據Recordthedatain七、 試驗結果Test試驗載荷達到1.5Fss=300N輔助支架未屈服Thebracketdoesntwhentheloadreaches八、試驗結論Test派力奧前減振器輔助支架的屈服載荷試驗滿足圖紙及標準Theyieldtest of the assistant bracket of the f