協作安裝說明vcs-gw pbx

1、組網結構為MCU H323一下是語音網關配置: 2921gwenPassword: 2921gw#ter len 0 2921gw#show runBuilding configuration.在 VCS-C，VCS-C 與 2921 語音網關做 Neighbor zone SIP Trunk。Current configuration : 4109 bytes! Last configuration change at 03:56:04Thu Dec 20 2012 by 2921gwver15.2service timestservice timests debug datetime ms

2、ecs log datetime msecno service password-encryption!hostname 2921gw!boot-start-marker boot-end-marker!card type e1 0 0enable password cisco!aaa new-m!aaa ses-id commonnetwork-clock-participate wic 0network-clock-select 1 E1 0/0/0!no ipv6 cef!no ipipip ceflookupname 0multilink bundle-name authenticat

3、ed!isdn switch-type primary-net5!voice-card 0 dspfarmdsp servidspfarm!voice rtp send-recv!voiervice potsno direct-inward-dial isdn!voi/IP-TO-IP GW，配置主要用于和 VCS 做 SIPervice voipTRUNK。ip address trusted listallow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323allow-

4、connections sip to sipno supplementary-servino supplementary-servi fax protocol t38 ver h323sipip moved-temporarilyip refer0 ls-redundancy 0 hs-redundancy 0 fallback none/SIP Trunk 配置registrar server expires max 3600 min 3600transport switch udp tcplocalhost dns:0!voice class codec 1codec preference

5、 1 g711ulaw codec preference 2 g729r8 codec preference 3 g711alaw codec preference 4 g722-56 codec preference 5 g722-48codec preference 6 g722-64!voice translation-rule 1rule 1 /49(0245689)$/ /1/!voice translation-rule 2 rule 1 /7(.*)$/ /1/!voice translation-profile fr- translate called 1!voice tran

6、slation-profile fr-vcs translate called 2!ing translation-profile fr-vcs!/轉換規則，視實際撥號規則而設定。license udiCISCO2921/K9 sn FGL163410EYhw-module pvdm 0/0!username 2921gssword 0 ciscousername admin privilege 15 password 0 cisco!redundancy!controller E1 0/0/0pri-group timeslots 1-10,16!erface Embedded-Servic

7、e-Engine0/0 no ip address!erface GigabitEthernet0/0ip address 0 40/配置 E1 卡為 ISDN Pri 信令duplex autospeed auto!erface GigabitEthernet0/1no ip address shutdown duplex auto speed auto!erface GigabitEthernet0/2no ip address shutdown duplex auto speed auto!/ISDN D 信道配置，主要用于與客戶 PBX 對接，用erfaerial0/0/0:15為西門

8、子，Pri 信令。戶no ip addressencapsulation hdlcisdn switch-type primary-net5isdning-voice voiceisdn bchan-number-order ascendingno cdp enable!ip forward-protocol nd!ip http serverip http authentication aaa no ip http secure-serverip http path flash:!ip route 3!control-plane!voice-port 0/0/0:15!profile def

9、ault!s s s!s/可忽略，實際并沒使用 CME 功能local GigabitEthernet0/0ccm 0 identifier 1 ver7.0/可忽略casso assooup 1te ccm 1 priority 1te profile 1 register GW-XCD!dspfarm profile 1 transcode codec g729abr8codec g729ar8 codec g711alaw codec g711ulawcodec g729r8/可忽略，CME 上的 codec 配置。um sess 4assote application S!dial-p

10、eer voice 11 voipdestination-pattern 2456891234/到 MCU 上會議 id 的 dialplan。sessesprotocol sipv2ipv4:2voice-class codec 1dtmf-relay sip-notify h245-alphanumeric rtp-nte no vad!dial-peer voice 13 pots destination-pattern .T port 0/0/0:15!/出的 dial-peergatekeepershutdown!ephony-service sdspfarm units 2 sds

11、pfarm tag 1 GW-XCD/可忽略，并未使用 CMEmax-ephones 50max-dn 100ip source-address 0 port 2000 strict-matchtimeoutserdigit 3max-conferen8 gain -6web admin system name admin password ciscodn-webedittime-webedittransfer-system full-consulttransfattern .Tcreate cnf-files ver-stJan 01 2002 00:00:00!ephone-dn1number 86666!ephone1mac-address 047D.7B03.514B button1:1!line con 0line aux 0line 2no activation-character no exectransport preferred nonetransport input alltransport output padnet rlogin lapb-ta mop udptn v120 sshstits