m043直升機甲板和安全附件helicopter deck safety net rev0-issue official

1、Doc. Title: CommisFor Helicopter Deck Safety Net直升機甲板安全網調試程序Doc. No. :-M043- Helicopter Deck Safety Net Project No.: H6001Unit:R-550D Jack-up Drilling UnitREVI0SIGNDATEPREPAREDREVIEWEDAPPROVED中 船 黃 埔 文 沖 船 舶CSSC HUANGPU WENCHONG SHIPBUILDING COMPANY LIMITEDTHIS DATA (OR) PARTS THEREOF, ARE HPWS PROP

2、ERTY AND THUS SHALL NOT BE USED IN ANY FORM WITHOUT PERMISTABLE OF CONTENTS1GENERAL31.1Pure31.2Responsibility31.3References and Drawings3Engineering Drawings3Mechanical and Electrical Completion Inspection Test Record3機械和電氣完工測試. 32345SYSTEM DESCRIPTION4SCOPE4PRE-REQUISITES4EXECUTION45.1System Checkl

3、ist45.2Safety Precautions45.3Fieldnel Deployment55.4Inspection by Vendors Service Represenive56COMMISING PROCEDURES56.1Safety Net Test57TEST ACCEPTANCE61GENERAL1.1PureThe pure of this procedure is to give clear instructions for the activities to be carried out tocomplete the commising of the describ

4、ed system.To ensure proper installation of safety net.To demonstrate the operational capabilities of the safety net.1.2ResponsibilityAny updates/revis of thiswill be the responsibility of the Commising Team. Anydeviations from this procedure will have to beed. In case of major changeshe workdescribe

5、dhis procedure (e.g. reduced scope of operating tests to be performed), a reviof theprocedure is required.任何更新/文件的修改都是調試團隊的義務程序任何的偏差都需將化，這個程序的工作必須修改程序版本（例如：減少操作測試）下來假如發生變1.3References and Drawings1.3.1Engineering Drawings1.3.2 Mechanical and Electrical Completion Inspection Test Record機械和電氣完工測試Item項

6、目Description描述Initial初始NameDate日期MCReview Mechanical Inspection Test Reports for:機械檢查Safety netNoDrawing No.DescriptionRemark1HP6001-H100-12General Arrangement Plan-Quarters Roof & Helicopter deck總布置圖-生活區頂層及直升機甲板2SYSTEM DESCRIPTIONHelicopter deck safety net is used to protect people from falling dow

7、n accidently.3SCOPEThis procedure covers safety net test.4PRE-REQUISITESAll the equipment shall be properly installed.All the electrical control panel and cables shall be properly installed and connected.The following is required for sucCrane with slingsful commising of the system:Sand bag of 100kg

8、test weightNote: All test instruments shall bear evidence of calibration within 12 months of test.5EXECUTION5.1System Checklist5.2Safety PrecautionsItemDescriptionInitialNameDateaAll commising activities must be in accordance with the HPWS permit-to-work system.bThe permit-to-work system shall speci

9、fy the conditions of work and precautions to be taken during the execution of the commising work to protectnel, plant and theItemDescriptionInitialNameDateaThe helicopter safety nes been installed as per Northsea drawing Helideck layout and Helideck safety net layout .Ensuret mounting and connection

10、 by ABS and ed by HPWS QC.5.3Fieldnel Deployment5.4Inspection by Vendors Service Represenive6COMMISING PROCEDURES6.1Safety Net TestNo.DescriptionHPWSAODABS6.1.1Drop the test load of 125Kg form 1.0 meter above the safety net.Check the safety net is strong enough to withstand, without damage, does not

11、 aa troline giving a “bounce” effect.6.1.2Repeat item (1) as many times as determined by the framing support configuration(s). For every differentItemDescriptionInitialNameDateaAll the mechanical components of the system are installed to vendors specificationbAll the electrical components of the sys

12、tem are installed to vendors specificationcVendors service engineer to verify t the system is ready and safe to be start up and commisedItemDescriptionInitialNameDateaEnsure requirednel are sioned properlybEnsure requirednel are sioned at helicopter deckcEnsure safetynel are sioned at the right plac

13、eenvironment.cAll commisingnel shall receive training to the level of their individual responsibilities on thepermit-to-work system prior to its commencement.dAll activities shall be carried out in accordance with the HPWS Safety Procedures, Project Standards and Sutory Regulations.eHPWS commising e

14、ngineers and supervisors will ensuret allnel involvedhe activity / work scope assisthe completion of hazard identification as per HPWS procedure.7TEST ACCEPTANCEThe units and system covered under this test meve been tested accordingly and found tobe satisfactory in accordance with test procedures.REPRESENIVENAMESIGNATUREDATEHPWSAODAB