結構工程圖標注的方法與技巧2016-3-17(1)

1、Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.Prepared By: GoerTekDate: 03/02/2016Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.2線性尺寸標注角度尺寸標注圓/圓弧尺寸標注小尺寸標注Goertek Proprietary and

2、Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.3Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.4Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.5

3、Tuba Bottom coverGoertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.6Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.7Goertek Proprietary and Confidential Background Technology and IP.

4、Do Not Disclose to Unauthorized Parties.81. 技術要求2. 詳細尺寸參照3D文件： ray_3d_bottom_housing.prt.1 ；3. 產品材質：PC7015-10 ;顏色：Black；表面處理：VDI 24; 4. 禁止使用水口料，水口修剪平至設計膠位或以下；5. 3D 圖中未做拔模斜度0.5 max.(指后模部份)；3D 圖中未倒圓角R0.20mm max.；6. 零件表面分模線最高允許高度：0.03mm；7. 零件不得有縮水、頂白、劃傷、拖花、披鋒，流痕以及其他缺陷；8. 進膠口、分模線、頂針、斜頂，行位等模具結構必須由歌爾公司結構工

5、程師確認；9. 頂針痕跡要低于設計膠位00.05mm；模具及產品的各類標示做成凹字(字深0.15mm MAX)10. 符合Goertek產品環保標準;11. 其他環保要求：無Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.9Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Partie

6、s.10Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.111. 技術要求2. 詳細尺寸參照3D文件： ray_3d_bottom_housing.prt.1 ；3. 產品材質：PC7015-10 ;厚度：0.2mm.顏色：黑色;表面處理：鍍鎳; 4. 產品周圍壓毛邊,銳角倒鈍角；5. 符合Goertek產品環保標準;6. 其他環保要求：無Goertek Proprietary and Confidential Backgroun

7、d Technology and IP. Do Not Disclose to Unauthorized Parties.12技術要求1. 產品材質：SUS304 ;.顏色：黑色;表面處理：鍍鎳; 2. 產品周圍壓無壓痕，產品表面要清洗，鐵屑，油污；3. 電鍍要求：鹽霧測試要過48H以上；4. 符合Goertek產品環保標準;5. 其他環保要求：無Goertek Proprietary and Confidential Background Technology and IP. Do Not Disclose to Unauthorized Parties.13技術要求1. 產品材質：3M 9075 ;顏色：黑色;厚度：T=0.05mm2. 產品周圍壓無壓痕，產品要整潔，無褶皺，無毛屑等；3. 符合Goertek產品環保標準;4. 其他環