空調中英文對照表

1、目 錄1.Specification技術參數32.Core Parts核心部件53.Multi Variable Units 多聯機64.Chiller水機115.PTAC 窗機156.Wall -mounted Unit掛 機237.Floor Standing Unit立柜機298.Ceiling Cassette Unit天花機329.Duct Unit風管機4010.Floor &Ceiling Unit座吊機4411.Electronic Control電控481. Specification技術參數1.1. Indoor Air Inlet DB（dry bulb）Temp

2、 室內進風干球溫度1.2. Indoor Air Inlet WB (wet bulb)Temp 室內進風濕球溫度1.3. Outdoor Air Inlet DB Temp 室外進風干球溫度1.4. Outdoor Air Inlet WB Temp 室外進風濕球溫度1.5. Indoor Air Outlet DB Temp 室內出風干球溫度1.6. Indoor Air Outlet WB Temp 室內出風濕球溫度1.7. Static Pressure靜壓1.8. Pressure Difference壓差1.9. Airflow Volume風量1.10. Dimension 尺寸

3、1.11. Noise Level 噪音等級1.12. Return Air Temp回氣溫度1.13. Discharge Air Temp排氣溫度1.14. Enthalpy Difference焓差1.15. Dehumidification除濕1.16. Sensible Heating Capacity顯熱量1.17. Latent Cooling Capacity 潛在制冷量1.18. Total Heating Capacity總制熱量1.19. COP能效比1.20. Rated Voltage額定電壓1.21. Rated Current額定電流1.22. Rated Pow

4、er Input額定輸入功率1.23. Frequency頻率1.24. Refrigerant Charge 冷媒充注1.25. Net Weight 凈重1.26. Gross Weight 毛重1.27. Model 型號2. Core Parts核心部件2.1. Compressor壓縮機2.2. Condenser冷凝器2.3. Throttle components節流部件2.4. Capillary毛細管2.5. 4-way reversing valve四通閥2.6. Electronic expansion valve (EEV)電子膨脹閥2.7. Thermostatic

5、expansion valve熱力膨脹閥2.8. Evaporator蒸發器2.9. Vapor-liquid separator氣液分離器2.10. Electronic parts box(E-parts box)電控盒2.11. One-way valve單向閥3. Multi Variable Units 多聯機3.1. Front panel前面板3.2. Ironclad asynchronous motor for outdoor unit異步鐵殼室外電機3.3. Motor Bracket電機支架3.4. Front maintenance board前維修板3.5. Left

6、 side board左側板3.6. Septum plate中隔板3.7. Welding assy for suction pipe回氣管焊接組件3.8. Suction pipe回氣管3.9. Oil return capillary transition tube回油毛細管過渡管3.10. Chassis assy底盤組件3.11. Chassis 底盤體3.12. Chassis foot底腳3.13. Chassis reinforced board底盤加強板3.14. Compressor 壓縮機3.15. One-way valve assy單向閥組件3.16. Connect

7、ing pipe for high pressure one-way valve高壓單向閥連接管3.17. Filter過濾器3.18. One-way valve單向閥3.19. Valve seat assy閥座板組件3.20. Valve seat 閥座板3.21. Cut-off valve for two connecting pipes雙接管截止閥DN133.22. Rear panel后面板3.23. Right side board右側板3.24. Large handle大抽手3.25. Protection grill 防護網3.26. Condenser preweldi

8、ng assy冷凝器預焊組件3.27. Two-row condenser 兩排冷凝器3.28. Condenser exhaust receiver welding assy 冷凝器集氣焊接組件3.29. Current dividing capillary assy of condenser 冷凝器分流毛細管組件3.30. Condenser main outlet pipe 冷凝器總出管3.31. Fixing pipe of condenser main outlet pipe 冷凝器總出管固定管3.32. Adfluxion pipe assy匯流管組件3.33. Adfluxion

9、 pipe 匯流管3.34. DN8 Copper adapter with holderDN8帶座銅接頭3.35. Connecting pipeto low pressure valve低壓閥連接管3.36. Electronic expansion valve assy 電子膨脹閥組件3.37. Electronic expansion valve 電子膨脹閥3.38. Plastic encapsulating coil塑封線圈3.39. Expansion valve capillary膨脹閥毛細管3.40. E-shape filter E型過濾器3.41. DN4 Copper

10、adapter with holder DN4帶座銅接頭3.42. Filter for oil return pipe 回油管道過濾器3.43. 4-way reversing valve assy 四通閥組件3.44. 4-way reversing valve 四通閥3.45. 4-way valve reversing coil assy 四通閥線圈組件3.46. Discharge pipe assy 排氣管組件3.47. Discharge pipe排氣管3.48. Installation copper tube for probe 探頭銅管3.49. Oil return pi

11、peline filter 回油管道過濾器3.50. Oil separator 油分離器3.51. Separator 分離器3.52. Top panel foam assy頂蓋板貼棉組件3.53. Rear frame后邊框3.54. Electronic control components電控部件3.55. Welding assy for E-parts box 電器盒焊接組件3.56. Cooling fin fixing board 散熱片固定板3.57. Cooling fin散熱片3.58. Main board assy for ourdoor unit室外主板組件3.5

12、9. Module board assy for outdoor unit室外模塊板組件3.60. Module board transformer assy for outdoor unit室外模塊板變壓器3.61. Monophase filter單相濾波器3.62. Rubber ring橡膠圈(小過線圈)3.63. Amorphous inductor非晶電感3.64. Eliminator擋水板3.65. Small handle小抽手3.66. Propeller fan軸流風葉3.67. Plastic front net塑料前網罩4. Chiller水機4.1 Front an

13、d rear support for wind inlet guide導風圈前后支撐4.2 Front and rear support assy for fan風機前后支撐組件4.3 Middle support assy for fan 風機中支撐組件4.4 Sealing board for condenser 冷凝器封板4.5 Lateral support for wind inlet guide導風圈側支撐4.6 Front and rear beam前后橫梁4.7 Lateral beam assy側橫梁組件4.8 Pipe clamp管夾4.9 Fixing board for

14、 distributor分流頭固定座4.10 Trigonal board 三角板4.11 Condenser assy冷凝器部件4.12 Water pan assy接水盤組件4.13 Vertical shaft assy立柱組件4.14 Evaporator干式蒸發器4.15 Vapour-liquid separator 汽液分離器4.16 Compressor壓縮機組件4.17 Compressor support assy 壓縮機支撐板組件4.18 Support for vapour-liquid separator氣分支架組件4.19 Pipe support管支架4.20 H

15、igh-pressure switch高壓開關4.21 Suction pipe components 回氣管部件4.22 Low-pressure switch低壓開關4.23 Throttle componets 節流部件4.24 Electronic expansion valve (EEV)電子膨脹閥4.25 EEV coil電子膨脹線圈4.26 4-Way reversing valve components四通閥部件4.27 4-Way reversing valve coil 四通閥線圈4.28 Pressure switch壓力開關4.29 Discharge pipe com

16、ponents排氣管部件4.30 Base assy底座組件4.31 E-parts components電控部件4.32 Current transformer電流互感器4.33 Crankcase heater曲軸箱加熱器4.34 Adapter board for 4-way reversing valve四通閥轉接板4.35 Main control panel控制主板4.36 Envirionment temperature sensor環境溫度傳感器4.37 System water inlet temperature sensor系統進水溫度傳感器4.38 System wate

17、r outlet temperature sensor系統出水溫度傳感器4.39 Unitary water outlet temperature sensor單元出水溫度傳感器4.40 Fin temperature sensor翅片溫度傳感器4.41 Fan capacitor風機電容4.42 Alternating contactor交流接觸器4.43 Power terminal電源端子臺4.44 Main board transformer主板變壓器4.45 Engineering terminal工程端子臺4.46 Trigonal set sqare固定三角板4.47 Compr

18、essor support assy 壓縮機支撐板組件4.48 Wire trough support線槽支架4.49 Middle support for wind inlet guide導風圈中支撐4.50 Vertical support for wind inlet guide導風圈縱支撐4.51 Support assy for fan風機支架組件4.52 Outdoor unit motor室外電機4.53 Propeller fan軸流風葉5. PTAC 窗機5.1. Air filter防塵網5.2. Control panel cover操作蓋板5.3. Front pane

19、l 前面板5.4. Self-locking switch自鎖開關5.5. Connection bar連桿5.6. Horizontal louver水平導風條5.7. Heat-insulation foam for air-out出風口保溫棉5.8. Scroll case base components風殼座部件5.9. Centrifugal fan離心風輪5.10. Fresh air inlet lever新風門連桿5.11. Fresh air inlet新風門5.12. Scroll case cover風殼蓋5.13. Air deflector導風板5.14. Fixin

20、g board for vertical louver導風板固定板5.15. Capacitor clamp電容卡5.16. Capacitor cap電容帽5.17. Compressor capacitor壓縮機電容5.18. Motor電機5.19. Connecting board搭板5.20. Propeller fan軸流風葉5.21. Rear cover 后蓋板5.22. Rear brattice后圍板5.23. Shutter clamp百葉窗夾5.24. Left shutter frame安裝左框條5.25. Cabinet component外箱部件5.26. Upp

21、er shutter frame上框條5.27. Installation support 安裝支撐5.28. Nut 螺母5.29. Bolt 螺栓5.30. Lower shutter frame下框條5.31. Right shutter frame右框條5.32. Shutter密封百葉5.33. Connection bar to cabinet外箱連接條5.34. Shutter locking bar 卡條5.35. Motor capacitor電機電容5.36. Temperature controller 溫控器5.37. Main switch 主令開關5.38. Kno

22、b旋鈕5.39. Control panel控制面板5.40. Control box控制盒5.41. E-parts box電控盒5.42. Evaporator assy蒸發器組件5.43. Suction pipe assy回氣管組件5.44. Capillary assy 毛細管組件5.45. Condenser output pipe冷凝器輸出管5.46. Input pipe for evaporator蒸發器輸入管5.47. Input pipe for condenser冷凝器輸入管5.48. Condenser assy冷凝器組件5.49. Compressor wiring

23、 cover nut壓縮機接線蓋螺母5.50. Washer for compressor wiring cover壓縮機接線蓋墊片5.51. Compressor wiring cover壓縮機接線蓋5.52. Overcurrent protector for compressor壓縮機過流保護器5.53. Wire to overcurrent protector過流保護器線體5.54. Sealing gasket for wiring cover接線蓋密封片5.55. Compressor壓縮機5.56. Rubber cushion for compressor壓縮機膠墊5.57.

24、 Fixinging nut for compressor壓縮機固定螺母5.58. Fixing gasket for compressor 壓縮機固定墊片5.59. Motor support 電機支架5.60. Chassis 底盤5.61. Fixing sheet for front panel 前面板固定片5.62. Front panel 前面板5.63. Transformer變壓器5.64. Transformer box 變壓器盒5.65. Display board assy顯示板組件5.66. Main control board assy主控板組件5.67. Air-i

25、nlet board 進風孔板5.68. Evaporator base蒸發器底座5.69. Cover蓋板5.70. Front brattice前圍板5.71. Protecting clamp fro power cord電源線保護卡5.72. Protecting U-clamp for power cord 電源線保護圈5.73. Scroll case渦殼5.74. Air -out frame出風口5.75. Self lock switch自鎖開關5.76. Cover for E-parts box電控盒蓋板5.77. Left fixing plate for chassi

26、s底盤左固定板5.78. Right fixing plate for chassis 底盤右固定板5.79. Supporting bar for installation安裝支承條5.80. Discharge pipe排氣管5.81. Clamp for wires電線中間夾子5.82. Fixing board for E-parts box電控盒固定板5.83. Rear cover for control box線路板蓋5.84. Power cord clamp電源線夾5.85. Front cover前蓋板5.86. Long connecting board長搭板5.87.

27、Rear cover后蓋板5.88. Wind guiding board導流板5.89. Water proof rubber ring 防水橡膠圈5.90. Rear rubber ring for motor電機后橡膠圈5.91. Front rubber ring for motor電機前橡膠圈5.92. Short connecting board 短搭板5.93. Pin銷5.94. Expansive core膨脹芯5.95. Fixing plate for chassis底盤固定板5.96. Installation support 安裝支架5.97. Front panel

28、 components前面板部件5.98. Electronic control components電控部件5.99. Control box assy控制盒組件5.100. Installation parts 安裝附件5.101. Remote controller遙控器5.102. Clamp for temp sensor溫包卡5.103. Wind inlet guide導風圈5.104. Swing switch 搖擺開關5.105. Sychronous motor 同步電機5.106. Defrosting temp controller化霜溫控器5.107. Rear si

29、de board 后側板5.108. Adjusting bolt 調整螺栓5.109. Rubber plug 橡膠塞5.110. Sealing gasket 密封圈5.111. Drain hose出水接管5.112. Right lower fixing clamp for motor電機下壓蓋(右)5.113. Right upper fixing clamp for motor電機上壓蓋(右)5.114. Left upper fixing clamp for motor電機上壓蓋(左)5.115. Left lower fixing clamp for motor電機下壓蓋(左)

30、5.116. Water pan接水盤5.117. Power cord電源線5.118. Wire joint二位接線座5.119. Frame fixing board面框固定板5.120. Drive gear傳動輪5.121. Wire joint panel接線底板5.122. Heater cut-out assy熱熔斷器組件5.123. PTC heaterPTC發熱器6. Wall-mounted Unit掛 機6.1. Front panel前面板6.2. Air filter 防塵網6.3. Screw cap螺絲蓋6.4. Panel frame面框6.5. Air cl

31、eaner復合式空氣清新網6.6. Air cleaner upper cover 清新器上蓋6.7. Window receiver 接收窗片6.8. LED indicator 顯示燈鏡6.9. Horizontal louver水平導風葉6.10. Upper horizontal louver導風條（上）6.11. Lower horizontal louver導風條（下）6.12. Vertical louver 垂直導風葉6.13. Air out frame 出風框6.14. Louver holder 導風葉連桿6.15. Sychronous motor同步電機6.16. D

32、rain hose出水喉6.17. Evaporator temp sensor assy蒸發器溫度傳感器組件6.18. Left holder for evaporator蒸發器左支板6.19. Evaporator 蒸發器6.20. Waterproof board assy擋水板組件6.21. Bearing holder 軸承座6.22. Cross flow fan, assy貫流風輪組件6.23. Chassis底盤6.24. Rear cover for chassis底盤后蓋板6.25. Installation plate for indoor unit室內機安裝板6.26.

33、 Little installation plate 小安裝板6.27. Connecting pipe clamp 配管固定卡6.28. Fan motor風機電機6.29. Motor cover電機蓋6.30. E-parts box cover電控盒蓋6.31. Indicator holder顯示燈座6.32. Display board assy顯示板組件6.33. Display board enclosure顯示燈罩6.34. Main control board主電控板6.35. Transformer變壓器6.36. E-parts box電控盒6.37. Wire cla

34、mp壓線條6.38. Wire joint, 5p小五位接線座組6.39. Remote controller遙控器6.40. Remote controller installation support assy遙控器安裝支架組件6.41. Display panel 顯示面板6.42. Relay holder繼電器底座6.43. Protection box for relay 繼電器保護盒6.44. Bush襯套6.45. Installation board for louver百葉安裝板6.46. Wire clamp for power cord電線壓條6.47. Relay繼電

35、器6.48. Switch board assy開關板組件6.49. Installation board base安裝板座6.50. Fan capacitor風機電容6.51. Strengthening board for chassis底盤加強板6.52. Supporting board for chassis 底盤下板6.53. Fan wheel support風輪支架6.54. Louver connecting bar搖擺連桿6.55. Right support for evaporator 蒸發器右支承6.56. Installation plate for main b

36、oard 電路板安裝座6.57. Installation plate for wire joint 接線座安裝板6.58. Bear holder軸承座6.59. Control board assy控制面板組件6.60. Protecting plate防護片6.61. Air cleaner cover濾清器蓋6.62. Right cover for motor電機右蓋板6.63. Fixing clamp for motor電機固定卡6.64. Right cover for panel frame面框缺口封板6.65. Wind guide on chassis底盤導風板6.66.

37、 E-parts components電控部件6.67. Plug堵塞6.68. Lower clap for panel frame面框下卡扣6.69. Upper clap for panel frame面框上卡扣6.70. HEAP filterHEAP濾網6.71. Copper nut, TLM-A01銅螺母TLM-A016.72. Copper nut, TLM-B02銅螺母TLM-B026.73. Sponge海綿6.74. Foam泡沫6.75. Right joint board of Evaporator蒸發器右連接板 6.76. Right side board of f

38、ront evaporator前蒸發器右邊板6.77. Right side board of rear evaporator后蒸發器右邊板7. Floor Standing Unit立柜機7.1. Air out frame assy出風框部件7.2. Conection bar for horizontal louver橫導風條連桿7.3. Sealing foam for air outlet frame出風框邊密封泡沫7.4. Display box assy顯示控制盒部件7.5. Control box assy控制盒底座7.6. Front panel components前面板部

39、件7.7. Sealing board密封板7.8. Cover components蓋板部件7.9. Water pan components接水盤部件7.10. Evaporator蒸發器7.11. Inlet pipe assy for evaporator蒸發器輸入管組件7.12. Outlet pipe for evaporator蒸發器輸出管組件7.13. PTC eletric heating componentPTC電加熱部件7.14. Left side board component左側板部件7.15. Top cover components頂蓋部件7.16. Chass

40、is components底盤部件7.17. E-parts box電器盒7.18. Fan motor capacitor電機電容7.19. Main control board assy主控板組件7.20. Electric heating control board assy電輔熱輔助組件7.21. Transformer變壓器7.22. Wire joint, 5p大五位接線座7.23. Wire clamp壓線板7.24. Right side board components外箱右側板部件7.25. Chassis底盤7.26. Fan motor for indoor unit室

41、內風扇電機7.27. Drain pipe排水管7.28. Centrifugal fan離心風輪7.29. Wind inlet guide導風圈7.30. Wind inlet grille components進風格柵部件7.31. Air filter空氣濾塵網7.32. Remote controller遙控器7.33. Indoor temp sensor室溫傳感器7.34. Pipe temp sensor管溫傳感器7.35. E-parts box cover電器盒蓋7.36. Scroll case components渦殼部件7.37. Installation box f

42、or main board電路板安裝盒7.38. Anion generator components負離子發生器部件7.39. Anion generator support負離子發生器支架7.40. Anion generator box負離子發生器盒7.41. Anion generator負離子發生器7.42. Right front board for evaporator蒸發器右側前擋板7.43. Front panel前面板7.44. Motor holder電機座7.45. Electric heater assy電加熱管電加熱組件7.46. Lower cover for e

43、vaporator蒸發器下?lián)醢?.47. Rubber underlay for motor電機減振橡膠墊8. Ceiling Cassette Unit天花機8.1. Water pan components接水盤部件8.2. Water drain plug排水塞8.3. Capacitor 電容8.4. E-parts box assy電控盒組件8.5. E-parts box cover電控盒蓋8.6. Transformer變壓器8.7. Main control board 主控板組件8.8. Wind inlet guide導風圈8.9. Nut螺母8.10. Fan clamp

44、風輪卡片8.11. Fan wheel components風輪部件8.12. Fan motor for indoor unit室內風扇電機8.13. Motor gascket電機鋼墊8.14. Evaporator base component蒸發器底座部件8.15. Chassis底盤部件8.16. Wire clamp board壓線板8.17. Sealing board for outlet pipe 出管密封板8.18. Installation hanger安裝吊鉤8.19. Expansion hanger膨脹吊鉤8.20. Drain pump assy排水泵組件8.21

45、. Water level sensor assy液位傳感器組件8.22. Pumping pipe clamp 抽水管卡環8.23. Pumping pipe抽水管8.24. Pumping coupling抽水接管8.25. Separating board for water pump水泵擋板8.26. Rubber washerfor water pump水泵膠墊8.27. Installation support for water pump水泵安裝架8.28. Panel components面板部件8.29. Installation cover安裝蓋板8.30. Cowling

46、導風板8.31. Filter濾塵網8.32. Grille switch格柵開關8.33. Grille switch cover格柵開關蓋8.34. Grille進風格柵8.35. Panel hanger assy面板吊鉤部件8.36. Control box控制盒8.37. LED support燈架8.38. Display board assy顯示板8.39. Control box cover控制盒蓋8.40. Panel面板8.41. Backup plate for air out 出風口墊板8.42. Fixing hanger for evaporator蒸發器固定鉤8.

47、43. Inlet pipe assy for evaporator 蒸發器輸入管組件8.44. Outlet pipe assy for evaporator 蒸發器輸出管組件8.45. Evaporator components蒸發器部件8.46. Fixing board for evaporator蒸發器固定板8.47. Rubber O-ring for wire crossing過線膠圈8.48. Pipe temp sensor管溫傳感器8.49. Indoor temp sensor assy室溫傳感器組件8.50. Remote controller遙控器8.51. Coup

48、ling聯軸器8.52. Bearing軸承8.53. Bearing holder軸承座8.54. Axis連接軸8.55. Electric throttle components電子節流部件8.56. Warning panel警示圖電器板8.57. Circuit diagram panel線路圖電器板8.58. Small wind inlet guide小導風圈8.59. E-parts components電控部件8.60. E-parts box welding assy電器盒焊接組件8.61. No.3 groove clamp 3號壓線扣8.62. PTC transfor

49、merPTC變壓器8.63. Fan capacitor風機電容8.64. Terminal of indoor unit室內端子臺8.65. Electronic control board for indoor unit室內電控板8.66. E-parts box電器盒8.67. Water pan assy水盤組件8.68. Auxiliary fixing board for evaporator蒸發器副固定板8.69. Pre-assembling assy for evaporator main fixing board 蒸發器主固定板預裝組件8.70. Main fixing b

50、oard for evaporator蒸發器主固定板8.71. Evaporator components蒸發器部件8.72. Evaporator baffle蒸發器擋板8.73. Evaporator 蒸發器8.74. Installation copper tube for probe探頭銅管8.75. Current dividing assy for evaporator蒸發器分流組件8.76. Current collecting pipe assy for evaporator蒸發器集流管組件8.77. Insulating tube保溫管8.78. Rubber insulat

51、ing tube橡塑保溫管8.79. Water pump水泵8.80. Liquid-level sensor液位傳感器8.81. Water pump motor holder水泵電機座8.82. Underlay for water pump support水泵支架墊塊8.83. Pre-assembling assy for upper foam上泡沫預裝件8.84. Centrifugal fan離心風葉8.85. Hanger掛角8.86. Rear brattice后圍板8.87. Pre-assembling assy for motor電機預裝組件8.88. One-axis

52、 indoor motor(YDK-35Q-8P3)單軸室內電機(YDK-35Q-8P3)8.89. Motor foot underlay電機腳墊8.90. Chassis assy底盤組件8.91. Right side board右側板8.92. Front brattice前圍板8.93. Drain pipe joint排水管接頭8.94. Side maintenance board for water pump水泵側維修板8.95. Lower pipe clamp下管夾8.96. Upper pipe clamp上管夾8.97. Valve panel assy閥板組件8.98

53、. Wire outlet frame 2出線護框28.99. Valve panel閥板8.100. Wire board壓線板8.101. Left side board左側板8.102. Water outlet pipe出水管9. Duct Unit風管機9.1. Air-out frame 出風口9.2. Front panel components前面板部件9.3. Evaporator蒸發器9.4. Input pipe assy輸入管組件9.5. Output pipe assy輸出管組件9.6. Pipe temp sensor assy of indoor unit室內管溫

54、傳感器組件9.7. Panel assy面板9.8. Air filter防塵網9.9. Canvas passage 帆布風道9.10. Base board for evaporator 蒸發器下襯板9.11. Water pan components接水盤部件9.12. Cover for middle beam橫梁上蓋組件9.13. Middle beam welding assy中間橫梁焊合件9.14. Chassis components底盤部件9.15. Left side board assy左側板組件9.16. wire-crossing board assy過線板組件9.17. Cover for right side board右側板蓋板9.18. Capacitor box電容盒9.19. Capacitor電容9.20. E-parts box cover電控盒蓋9.21. Installation support for remote controller遙控器安裝架9.22. Remote controller遙控器9.23. Electronic control components電控盒部件9.24. Elect