2汽車專業英語課件維護修理部分修改后section chapter945

1、復習o 提問（教師說出中文故障術語，同學回答對應英文術語）Chapter 8 Reading Repair Manuel 8.1 Diagnosing Automatic Tansaxle8.1 Diagnosing Automatic Tansaxle（A541EA541E） 9.4 How to Read and Use Wiring Diagrams 9.4 How to Read and Use Wiring Diagrams 9.5 How to read technical service bulletin9.5 How to read technical service bull

2、etin Chapter 8 Reading Repair Manuel9.4 How to Read and Use Wiring Diagrams 8.1 Diagnosing Automatic Tansaxle（A541E） 9.4 How to Read and Use Wiring Diagrams 9.4.1 Electrical Symbols9.4.2 Wiring Color Codes9.4.3 Samples of Reading and using Wiring DiagramHow to Read A Wiring Diagram How to use Wiring

3、 Diagram9.5 How to read technical service bulletin tool9.4 How to Read and Use Wiring DiagramsHow to Read a Volkswagen Wiring Diagram,See Figure 8-9 & 10 Figure 8-99.4 How to Read and Use Wiring Diagrams How to Read a Wiring Diagram（Volkswagen） Figure 8-10Chapter 8 Reading Repair Manuel9.4 How t

4、o Read and Use Wiring DiagramsVolkswagen Passat air conditioning blower circuit is shown in the following wiring diagram. Study carefully the circuit (Figure 8-11) and then describe the blowers operation. Figure 8-11 How to Diagnose a Fault by Using the Wiring Diagram Wiring diagrams are used for ma

5、lfunction diagnosis in the vehicle electrical system or on electrical components. The following example shows the malfunction diagnosis process on the electrical gearbox control using a wiring diagram. The manufacturers instructions must be observed during malfunction diagnosis.(B1-driving speed sen

6、sor, B2-gearbox input-speed sensor, X92-diagnosis connection, X34-ECU plug, gearbox control, S3-multifuction switch, A35-solenoid valves) Diagnostic Procedure Fault code 010C: Pressure-regulator solenoid valve, short circuit to earth/open circuit. 1. Read out fault memory The fault code indicates a

7、fault on the component or on the cables between the component and the ECU. 2. Disconnect ECU plug from ECU Checking of components and cables between the component and the ECU is often performed in the form of a resistance measurement. The plug must be detached from the ECU for this purpose. Warning:

8、 Turn off ignition beforehand! In the circuit diagram the detached plug is indicated by the interrupted cables to the ECU. 3. Determine test points The test points for the resistance measurement in the ECU plug must then be determined using the circuit diagram.Here: Measurement of the conductor and

9、coil resistance between contact numbers 22 and 58 with an ohmmeter (see Figure 8-11 and Figure 8-12). When using a test box, bear in mind that the contact numbers of the plug generally correspond to the contact numbers of the test box (see Figure 8-13). Important: Follow manufacturers instructions.

10、4. Reference/actual-value comparison(Figure 8-14) If the manufacturers specified reference value is not achieved, a cable fault must be ruled out by way of a resistance measurement of the cable between the component and the ECU. If the resistance value of the cable and the cable contacts are OK, the

11、n the component is faulty.Figure 8-12 Determine test pointsFigure 8-13 Using a test boxFigure 8-14 Reference/actual-value comparisonChapter 8 Reading Repair Manuel9.5 How to read technical service bulletin New Wordsbulletinbulitinn.公報，公告，新聞快報，學報公報，公告，新聞快報，學報Taptpv.輕拍，輕叩，輕敲輕拍，輕叩，輕敲Chapter 8 Reading Repair Manuel 9.5 How to read t