100T汽車吊性能表

1、100T主要性能與參數100T主要性能與參數項目數值最大額定總起重量100000 kg基本臂最大起重力矩3238kN.m最長主臂+副臂最大起重力矩1127kN.m主臂最大起升高度48m主臂+副臂最大起升高度62.1m外形尺寸（長X寬X高）14550 X 2750X 3750mm主臂長12.8-48m副臂長18.1m起重特性表PAT工作幅度WORKINGRADIUS(m)ED LIFTING CAPACITY TABLE主臂BOOM支腿全伸、后方、側方作業REAR&SIDE WORKING AREA WITH OUTRIGGER FULLYEXTENDED單位（主臂仰角BOOMANGLE

2、C ）JNIT ): Kg主臂+副臂45+9.5mBOOM+JIB45+16.0m臂長BOOM LENGTH副臂安裝角JIB OFFSET副臂安裝角JIB OFFSET12. 0m16. 2m20. 4m27. 0m33. 0m39. 0m45. 0m5°30°5°30°3.0100000700008060002500400013003.59200070000580007855002400360012004.08500070000540007650002300320011504.57600064000510003500074450022003000110

3、05.0700005800049000350007240002100270010505.563000510004500035000260007037002050250010006.05700046000430003400026000683400195024009506.5480004300041000330002600020000663200190022009007.0440004000039000320002600020000642900185021008507.537000370003500030500250002000015000622400180018008008.0340003400

4、0320002900040001900015000602000175015007509.0270002700027000250002250017500150005816001500120070010.02190021900022000205001650015000561400135011.018400190001950018000155001400012.015700160001650016000145001360014.01160001280013500130001200016.08400980010500110001050018.06300780082008500900020.060006

5、6007200750022.0500052005800620024.042004800520026.03800430028.03100360030.02900說明(NOTE ):以上作業工況均為支腿全伸，不允許在不打支腿的情況下吊重。(Above working condition is all withoutrigger fully extended,never lift a load on the wheels.)表中粗線以上數值是由起重機的結構強度所決定的，粗線以下數值是由起重機整機穩定性所決定的。(Capacities above the thick line in the table

6、 are based on the boom strength,the others,on stablitiy of the complete machine.)打好第五支腿時，表中數值適用于圓周360(With the 5th outrigger fully extended,full360rotation is available according to the values listed in the above table.)表中所列額定起重量為最大允許值，并包括吊鉤重量(100噸吊鉤重815Kg, 60噸吊鉤重560Kg, 6噸吊鉤重180Kg)和其他吊具的重量。 (The rat

7、ed lifting capacity listed in the table ismax.allowed value,including weight of the hookblock (the hookblock weight is 815kg for 100t,560kg for 60t,180kg for 6t)and other slings.)表中所給幅度值，是指吊載后吊鉤中心到回轉中心的水平距離。(A working radius given in the tableis a horizontal to the axis of the slewing ring when the hookblock is loaded.)當實際臂長和工作幅度在兩數值之間時，應按最大臂長和幅度值確定起重量。(When actual boomlength is between two values,determing lifting capacity according to bigger boomand radius.) 在副臂伸出的情況下使用主臂作業時，額定起重量不僅要扣除吊具的重量，還