北京友邦建通測繪儀器銷售有限公司

1、DQL-6型光學測樹羅盤儀 OPTICAL COMPASS MODEL DQL-6INSTRUCTION 哈 爾 濱 光 學 儀 器 廠HARBIN OPTICAL INSTRUMENT FACTORY CHINA一、 用途DQL-6型光學測樹羅盤儀，適用于森林資源調查中的各種測量工作。如距離、高差、方位、水平、坡角等。同時，可以測定和標定樹干任意部位的高度和直徑，每公頃胸高斷面積、立木行率、區分求積、造材求積等。也可用于農田水利、土地規劃、地形測繪等一般工程測量。二、 主要技術參數 望遠鏡：放大倍率16x有效孔徑20mm視場角.2°30視距乘常數.50，100視距加常數0最短視距2

2、m 磁羅盤： 磁針長度.67mm 度盤格值.1° 豎直盤： 度盤格值.1° 游標值.6 測高量程.±40m 水準器： 圓水準器15/2mm三、 儀器結構 儀器主要由望遠鏡組、豎盤組、羅盤組、安平組四部分組成，見圖1。望遠鏡組1為16倍內調焦式，并可在垂直面內作360度回轉，它不僅用來瞄準和測距，而且在分劃板上沒有測徑標尺可用來測定樹干直徑。豎盤組不僅是望遠鏡的回轉軸支架，而且裝有與望遠鏡同步轉動的豎直羅盤，盤面上刻有水平距為10m、20m、15m、30m的測高尺2，在水平距30m處可測量±40m高度。盤面下部還刻有角度尺4，可供傾角測量用。為操作方便，備

3、有橫軸止動螺旋3和微調螺旋5，可用于精確調整。羅盤組由磁針10和磁針度盤9組成。主要用于磁方位測量，為保證測量精度，羅盤合上還裝有圓形水準器11。安平機構6是球臼式機構，即可以與三腳架連接，又可以隨意調節，可迅速方便將儀器安平。四、 使用方法1、 基本操作1. 儀器安平 將儀器穩固的裝置在三腳架上，并使儀器的各可調部位均處中間狀態，調整球臼機構使羅盤之園水準器氣泡居中。2. 望遠鏡調節 首先旋轉目鏡視度圈，使眼睛清晰的看清分劃板十字絲，轉動儀器使望遠鏡粗瞄準器大致瞄準目標或標尺，在調節調輪，使之清晰的看清目標。2、 方位測量安平儀器，放開磁針止動螺旋7，望遠鏡十字絲豎絲瞄準目標，待磁針靜止后，

4、即可讀取該目標方位。3、 距離測量 調節望遠鏡至清晰的看清標尺刻度，讀取上、下夾距絲在標尺上所間隔的公分?jǐn)?shù)，乘以常數50，即得出儀器中心到標尺的距離；如讀取上、中兩絲或中、下兩絲在標尺上所間隔的公分?jǐn)?shù)，則乘以常數100，即得出儀器中心到標尺的實際距離。在測量時為了讀數方便，可以少量轉動微調螺旋5，使之其中一橫絲處于標尺上公分整數亦可。4、 角度測量 儀器安平后，調節望遠鏡通過分劃板橫絲瞄準被測目標后，可以在豎直度盤的角度尺上直接讀取角度。5、 高度測量 根據作業和實際需要，可將儀器安置在水平距為10m、15m、20m、30m任意一點，安平儀器后，用望遠鏡橫絲瞄準被測目標，然后可以在豎直度盤所對

5、應的水平距高度尺上讀取其高度（見圖2 a、b）a、平地測高時，仰角高度加儀器高度為總高度。b、坡地測高時，仰角高度加俯角高度為總高。圖二6、 上部直徑測量將儀器安置于適當水平距離處（根據作業環境任意選定），儀器安平后通過望遠鏡用常數100觀測被測樹木的水平距離在分劃板上間隔的公分?jǐn)?shù)，然后再用望遠鏡橫絲瞄準待測高度部位，并讀取所對應的仰角a，在調整水平微調螺旋，使望遠鏡分劃板上測徑標尺零線對準樹干一測，讀取樹干另一測在測徑標尺上的讀數d，則樹干上部直徑D可按下式計算：計測實例： 圖3所示，儀器至樹干的水平距離為18m，則在望遠鏡分劃板中讀得S=18cm，儀器瞄準待測高度部位時的仰角a=30

6、76;30，樹干在分劃板測徑標尺上。（如圖3）圖 三圖 四樹干在分劃板上讀數為1.2讀數值d=1.2（見圖4）。則該部位樹干直徑為在測量上部直徑的同時，亦可在測高尺上讀得該部位的高度。五、 儀器保養及注意事項1、 儀器出廠前已經過校驗，如儀器經過長途運輸、碰撞、劇烈震動或長期不曾使用時，在使用時，在使用前應對圓形水準器安平精度進行檢查，如有誤可通過三個帶孔螺釘8進行校正。2、 儀器使用完畢后，應將磁針鎖住以免軸尖磨損。各調整機構應復中間狀態，各制動機構應妥善鎖緊。3、 儀器應保存在干燥清潔處，防止各光學件生霉及金屬件銹蝕。4、 使用中望遠鏡光學零件表面應避免污物觸及，儀器經維修或拆裝后，必須重

7、新校準后方可使用。六、 儀器成套性1、 光學測樹羅盤儀.1臺2、 皮 合.1個3、 三腳架.1付4、 校正針.1支5、 使用說明書1份6、 合格證.1份7、 電子計算器（由用戶選訂的配件套）L I S TUseTechnical Data c)measurement of distanceStructure d) measurement of anglesInstructions for use e) measurement of heighta) preparation for measuring f) measurement of diameterb) azimuthal orientat

8、ion NoticeUse Optical Compass Model DQL-6 is applicable to surveys in forestry resources. For example, distance, differential altitude, azimuthal orientation, slope angle, trees height or diameter, etc. Besides, its suitable for agriculture, hydraulic engineering, geology and general engineering.Tec

9、hnical Data Telescope Magnification 16x Clear object aperture 20mm Field of view 2°30 Stadia multiplication constant 50.100 Stadia additive constant 0 Shortest focusing distance 2mCompass The division unit of dial 1 ° Vertical dial The division unit of dial 1 ° Vernier scale 6 Measuri

10、ng height range ±40m Precision of circular bubble 15/2mm Weight 1kg Size 130x100x220(mm)Structure Model DQL-6 is made up of telescope, vertical dial, compass and leveling unit. See Fig1 Fig11) telescope2) backing-up screw for telescope3) angles scale4) slow motion screw for telescope5) height d

11、ial6) eye lens7) adjusting screw with hole 8) backing-up screw for needle9) leveling unit10) horizontal dial11) needle12) cirular bubble Instructi ons for usea) Preparation for measuringFirst screw the instrument on the tripod, then adjust the leveling unit for keeping the circular bubble in the cen

12、ter. And all the adjustable parts should be kept in the proper position (not in the limit). In measuring, the telescope is the main part for taking aim, first adjust the eye lens till the cross hairs can be seen clearly through the eye lens, then adjust the focusing wheel up to the target can be see

13、n clearly, too. In this case, you can begin your work.b) Azimuthal orientation First release the needle by turning the button for needle and make the vertical line on the reticule plate in the same line with the target. Well you can get the reading after keeping the needle still.c) Measurement of di

14、stance First adjust the telescope till the scale on the rod can be seen clearly. If you get the reading on the rod between the up line and the down line on the reticule plate, the reading must time 50 and this is the distance form instrument to the rod. And if you get the reading on the rod between

15、the middle line and the up line or the domn line, the number must time 100 and this is the distance you wanted. You also can turn the slow motion screw for telescope 4 for getting reading easily.d) Measurement of angles First adjust the telescope and make the horizontal line on the reticule plate in

16、 the same line with the measured target. Then the angles degrees can be read straight off the scales of angles scale.e) Measurement of height Put the instrument at any point from distance of 10m, 15m, 20m or 30m, then adjust the telescope as in paragraph d) above. Now the height of tree can be got f

17、rom the height dial.(See Fig 2 a,b)f) Measurement of diameter Put the instrument in the proper position that you wanted. First measuring the horizontal distance(s) from instrument to the tree, then measuring the angle of elevation(a). After this turn the slow motion screw 4), as soon as the “zero” h

18、air line concides with one sicle of the tree, you can get the number (d) on the horizontal hair line (d is from “zero” to the other side of the tree). Well you can count the diameter according to the formula. For example (See Fig3、4) S=18cm a=30°30 d=1.2 thenNote: At the same time, you can measure the height of the trees same part.abFig2Fig3Fig4Notice1. The instrument has been adjusted before leaving factory. Please check the circular bubble before using it. If its not in the center, you can adjust again with the three