42期海船輪機員考試42801

1、中華人民共和國海事局2007年第1期海船船員適任證書全國統考試題(總第42期)科目：輪機英語 試卷代號：801適用對象：無限、近洋航區3000kw及以上船舶輪機長（本試卷卷面總分100分，及格分為70分，考試時間為100分鐘）答題說明：請選擇一個最合適的答案，并將該答案按答題卡要求，在其相應位置上用2b鉛筆涂黑。第1題至68題，每題1分，第69題至76題，每題15分，第77題至78題， 每題10分。一、單項選擇題1. during the valve overlap period, the exhaust pressure of a turbocharged four-stroke/cycle

2、 diesel engine must be less than the intake manifold pressure to ensure _. a. effective cylinder scavenging and cooling b. constant pressure from the turbochargers c. cooler operation of the exhaust system d. effective constant pressure for turbocharger operation 2. the relative air pressure in the

3、inlet manifold of a turbocharged diesel engine is usually _.a. greater than the average exhaust manifold pressure b. less than the average exhaust manifold pressure c. greater at the turbine wheel than at the impeller d. greater at reduced engine speed 3. cooling of engines is achieved by circulatin

4、g a cooling liquid around internal _within the engine.a. air b. passages c. pipes d. means 4. an over-speed safety device is usually fitted to a generator engine for _ in the event of over-speed. a. stabilizing the ship speed b. increasing the fuel pump setting c. braking the crankshaft d. cutting p

5、ower off the engine 5. the amount of fuel delivered by a helical plunger fuel injection pump is controlled by _. a. varying the pump discharge pressure b. varying the pump return pressure c. rotation of the pump plunger d. rotation of the pump barrel 6. prolonged operation of a diesel engine with a

6、closed cooling water system, at lower than normal designed operating temperatures can _.a. increase power output b. decrease lube oil viscosityc. eliminate fuel knock d. cause sulfuric acid formation 7. if the sump _ were to rise this would indicate water leakage into the oil and an investigation in

7、to the cause must be made. a. temperature b. viscosity c. lever d. level 8. in a diesel engine, when refitting piston rings you should_. i. check the ring gap at the smallest diameter of the cylinder ii. remove carbon from the ring groovea. i only b. ii only c. both i and ii d. neither i nor ii 9. f

8、uel has been injected but ignition fails. the possible cause may be _. a. slightly leaky exhaust valve b. increased scavenging air temperature c. engine cylinders not scavenged sufficiently d. too much water in the fuel oil 10. if some of the cylinders are not firing, the ones affected may be determ

9、ined by watching _. a. the exhaust temperature b. the exhaust pressure c. the governor d. the fuel flow meter 11. the major cause of trouble in a mechanical-hydraulic governor is contamination of the hydraulic fluid by _. a. dirt b. fuel oil c. governor cooling water d. fuel oil tar(焦油) 12. modern m

10、arine diesel engines equipped with mechanical fuel injection operate on a combustion phase within the cycle which is _. a. entirely constant pressure b. entirely constant temperature c. a combination of constant volume and constant pressure d. a combination of constant temperature and constant press

11、ure 13. a controllable pitch propeller on a diesel driven vessel eliminates the need for _. a. friction clutches b. disconnect clutches c. reversing gears d. reduction gears 14. propeller pitch speed minus ship speed divided by the propeller pitch speed is termed _. a. apparent slip b. true slip c.

12、pitch d. propulsive efficiency 15. pitted reduction gear teeth having a deep blue color with evidence of overheating have been operated with _.a. excessive speed b. improper warm-upc. extreme misalignment d. inadequate lubrication 16. a bypass line provided around a waste heat auxiliary boiler in a

13、diesel engine exhaust system, may be used to avoid boiler _. a. corrosion at low engine loads b. erosion at high engine loads c. overload at high engine loads d. scaling at all exhaust temperatures 17. a firebox explosion in an automatically fired auxiliary boiler may be the result of _. a. excessiv

14、e purging before lighting off b. insufficient trail for ignition period c. a faulty transformer in the ignition circuit d. insufficient purging before lighting off 18. a spur gear pump should be operated with the discharge valves _.a. slightly opened b. throttled c. fully opened d. halfway opened 19

15、. a centrifugal pump may fail to deliver water when first started if the _. a. water seal pipe is plugged b. pump is not primed c. seal ring is properly located d. impeller is flooded 20. the sum of the sensible heat and the latent heat of any substance is known as _. a. total heat b. residual heat

16、c. specific heat d. superheat 21. as the amount of moisture in the air increases, the difference between the dry bulb and wet bulb temperatures will _. a. increase b. decrease c. remain unchanged d. be greatest at dew point 22. which of the problems listed could cause erosion of the expansion valve

17、disks and seats? a. overcharging the system with refrigerant b. faulty compressor suction valve c. failure of the high pressure cutout d. flash gas formed in the liquid line 23. sludge may be formed in the oil in the crankcase of a reciprocating air conditioning compressor as a result of _. a. refri

18、gerant bubbles in the lube oil b. refrigerant reducing the lube oil viscosity c. oxidation of the lube oil from overheating d. reducing the floc or cloud point of the oil 24. _ are used to ensure that ships dont discharge oil when pumping out oily water from any oil contaminated space. a. boiler b.

19、incinerator c. oily water separator d. sewage treatment unit 25. the _ is used to burn oil sludge. a. clarifier b. oily water separator c. incinerator d. distiller 26. most marine biological sewage treatment plants consist of all the following statements except _. a. aeration tanks b. settling tanks

20、 c. disinfection agent d. anaerobic bacteria(厭氧細菌) 27. the separation of impurities and water from _is essential for good combustion of diesel engines. a. lube oil b. fuel oil c. turbine oil d. grease 28. which of the listed problems could produce a high absolute pressure within a flash type evapora

21、tor? a. production of high salinity distillate b. seawater feed temperature below 165 c. a leak in the first stage demister d. a cracked distillate pump vent line 29. among the basic categories of equipment, which of the following are used to convert mechanical into hydraulic energy? a. the hydrauli

22、c pumps b. valves c. hydraulic cylinders d. hydraulic motors30. mooring winch should be equipped with mechanical brakes which are capable of holding _. a. half the breaking strength of the mooring line b. the full breaking strength of the mooring line c. the maximum expected tension of the mooring l

23、ine d. 50% over the working tension of the mooring line 31. according to regulations, a power driven auxiliary steering gear for a vessel capable of a 12 knot service speed, must be able to meet the rudder movement requirements at which of the minimum vessel speeds listed below? a. 6 knots b. 7 knot

24、s c. 9 knots d. 12 knots 32. pressure drop in an operating hydraulic system is developed _. a. only by the pump as its primary function b. by resistance to the fluid flow through the system c. by the thermal input to the systems fluid d. solely(單獨地) by the charge applied by the accumulators 33. the

25、frequency of an alternator at a given rpm is determined by the _. a. number of turns of wire in the armature(電樞) coil b. number of magnetic poles c. strength of the magnets used d. output voltage 34. you are attempting to parallel two ac generators, and the synchroscope(同步器) pointer is revolving in

26、the fast direction. this indicates that the frequency of the incoming machine is _. a. higher than the bus frequency b. lower than the bus frequency c. the same as the bus frequency but out of phase with it d. the same as the bus frequency and the circuit breaker may be closed at any pointer positio

27、n 35. the load sharing characteristics of two diesel generators operating in parallel are mostly dependent on their governor _. a. load limit settings b. idle speed settings c. speed limit settings d. speed droop settings 36. the first requirement for logical troubleshooting of any system is the abi

28、lity to _. a. collect all available data on a casualty b. recognize normal operation c. identify the probable cause of a symptom d. isolate the faulty component 37. the purpose of a main switchboard circuit breakers reverse-power trip is to _.a. prevent main circuit overload b. protect the circuit b

29、reaker blowout coilc. prevent alternator motorization d. prevent low voltage tripout 38. an advantage of dc motors over ac motors is that they _. a. are less expensive b. require less maintenance c. can be started across the line d. offer a more effective means of controlling speed 39. prior to any

30、overhaul work on electric equipment, it is important to ensure the circuits are _. a. live b. dead c. excited d. on line 40. a circuit breaker differs from a fuse in that a circuit breaker _. a. melts and must be replaced b. is enclosed in a tube of insulating material with metal ferrules(環) at each

31、 end c. gives no visual indication of having opened the circuit d. trips to break the circuit and may be reset 41. the ratio of output response to a specified change in the input is known as _. a. primary feedbackb. sensitivity c. deviation d. dead band42. which of the listed devices is used to meas

32、ure pressure and convert it to an electrical signal? a. transducer b. reducer c. transformer d. rectifier 43. the meat box temperature control circuit, as used in the ship service refrigeration system, is an example of _. a. two position control b. single speed floating control c. proportional(比例) c

33、ontrol d. reset control 44. if both the high leveland low level alarms come on for the same address of a centralized（集中的） control console, the most likely problem is a/an _. a. sensor failure b. failed alarm c. low level d. extremely high level 45. when under maneuvering conditions with the machiner

34、y being manually operated the control unit or console should be _. a. automatically controlled b. continuously manned c. off power d. continuously unmanned 46. before the seas get rough, it is a good safety practice to_. a. secure loose gear b. move quickly about the ship c. increase lighting d. shu

35、tdown auxiliary equipment 47. which of the listed classes of fire would most likely occur in the engine room of a vessel? a. classes a and b b. classes b and c c. classes c and d d. classes a and d 48. to prevent the spread of fire by conduction, you should _. a. cool the bulkheads around the fire b

36、. remove combustibles from direct exposure c. close all openings to the area d. shut off all electric power 49. the fire extinguishing action of co 2 comes mostly from _. a. breaking the fire chemical chain reaction b. smothering c. cooling d. isolating the heat from the fuel 50. the necessity for a

37、dministering artificial respiration may be recognized by the victims _. a. vomiting(嘔吐) b. blue color and lack of breathing c. irregular breathing d. unconscious condition 51. when you notice oil on the water near your vessel while taking on fuel, you should first _. a. stop loading b. notify the se

38、nior deck officer c. notify the terminal superintendent d. determine whether your vessel is the source 52. the flash point of a liquid refers to the temperature _. a. at which a liquid will give off inflammable（易燃的） vapors b. at which a liquid will burn steadily c. at which a liquid will explode d.

39、that a liquid must reach before it will flow readily 53. why is it necessary to have routine testing of the cooling water? a. to ensure that the proper residuals of treatment chemicals, as specified, are maintained all time. b. to trace leakage in the cooling water system. c. it is not necessary. d.

40、 to detect the presence of contaminants in the water that may be injurious to the cooling system. 54. “amidships ” refers to_. a. back of the vessel b. the middle portion of a ship c. a backward movement of a vessel d. across the ship, at right angles to the fore-and-aft centerline 55. _, the second

41、 one will start automatically. a. if the first stand-by set failed b. if the first stand-by set fails c. if the first stand-by set will fail d. if the first stand-by set doesnt fail 56. the additional mark _in the classification certificate for machinery means propulsion apparatus is remotely contro

42、lled on the navigating bridge control station, and engine assembly control station is unmanned periodically. a. brc b. mcc c. aut-0 d. aut-1 57. the core(核心) item in the oil record book part i is_, and its main content is_. a. item a, ballast or cleaning of fuel oil tanks b. item b, discharge of dir

43、ty ballast or cleaning water from fuel oil tanks referred to under section(a) c. item c, disposal of oil residues(sludge) d. item h, bunkering of fuel oil 58. a shipboard oil pollution emergency plan is required of _. a. all vessels, regardless of size and commercial application b. any barge or othe

44、r ship which is constructed or operated in such a manner that no oil in any form can be carried aboard c. an oil tanker of 150 gross tons or above, or other ship of 400 gross tons or above d. an oil tanker of 400 gross tons and above, or other ships of 150 gross tons and above 59. during psc inspect

45、ion related to the ism code, _of the safety management system (sms) should be carried out if clear grounds are established. a. a less favorable inspection b. a more favorable inspection c. a less detailed inspection d. a more detailed inspection 60. all of the followings are the detainable deficienc

46、ies under the solas convention except _. a. failure of proper operation of propulsion and other essential machinery, as well as electrical installationb. failure of the proper operation of the main and auxiliary steering gearc. failure of engineering watch arrangements to conform to the requirements

47、 specified for the ship by administrationd. failure of the proper operation of emergency generator, lighting, batteries and switches61. when deciding the composition of the engineering watch, which may include _appropriately(適當?shù)?, many factors shall be taken into account. a. satisfied engineers b. q

48、ualified ratings c. satisfied chief engineer d. qualified chief engineer 62. the officer in charge of the engineering watch shall notify the chief engineer without delay_. a. in any emergency or if in any doubt as to what decision or measures to take b. in the event of any impending（迫近） action in ma

49、chinery spaces that may cause reduction in ships speed c. when isolating and bypassing machinery to be worked on d. co-operating with any engineer in charge of maintenance work 63. at an unsheltered(開放的) anchorage the chief engineer officer shall consult with _whether or not to maintain an underway

50、watch. a. the engineer officer in charge of watch b. the deck officer in charge of watch c. the master d. the chief mate 64. when off loading garbage to another ship, your records must identify that ship by name and _. a. home port b. operators name of record c. official number d. masters name 65. b

51、ilges may be pumped_. a. on the outgoing tide b. overboard after dark c. overboard through an anti-pollution equipment d. anytime in an emergency, i.e. main engine lube oil failure 66. according to the international regulations concerning the prevention of pollution of sea areas from ships, the disp

52、osal into the sea of all plastics is _. a. welcome b. admitted in some special sea areas c. prohibited d. acceptable 67. the company should establish in the sms that _has the overriding authority and the responsibility to make decisions with respect to safety and pollution prevention. a. the master b. the chief engineer c. the officer on duty d. the engineer in charge of watch 68. the ship security officer shall have knowledge and have received training, taking into account the guidance given in