機械專業術語[英語]

1、組裝、沖壓、噴漆等專業詞匯 Layout布置圖 fixture 夾具(治具) pallet棧板 barcode條碼 熔機 repair修理 operator作業員 QC品管 supervisor 課長 ME制造工程師 MT制造生技 lbs. inch鎊、英寸 chassis 基座 bezel panel面板 sheet metal parts 沖件 work cell工作間 personnel resource department 人力資源部 production department生產部門 planning department企劃部 QC Section品管科 stamping fac

2、tory沖壓廠 painting factory烤漆廠 molding factory成型廠 common equipment常用設備 uncoiler and straightener整平機 punching machine 沖床 robot機械手 hydraulic machine油壓機 lathe車床 planer |'plein|刨床 miller銑床 grinder磨床 driller?床 welder電焊機 staker=reviting machine鉚合機 position職務president董事長 general manager總經理 spe

3、cial assistant manager特助 factory director廠長 department director部長 deputy manager | =vice manager副理 section supervisor課長 deputy section supervisor =vice section superisor副課長 group leader/supervisor組長 line supervisor線長 assistant manager助理 to move, to carry, to handle搬運 be put in storage入庫 pack packing

4、包裝 to apply oil擦油 to file burr 銼毛刺 final inspection終檢 cleaning cloth抹布 scrape .v.刮;削 manufacture procedure制程 oxidation |' ksi'dein|氧化 scratch刮傷 dents壓痕 production capacity生產力 proposal improvement提案改善 spare parts=buffer備件 trailer=long vehicle拖板車 pressure plate=plate pinch壓板 bolt螺栓

5、 name of a department部門名稱 administration/general affairs dept總務部 power wire電源線 buzzle蜂鳴器 pedal踩踏板 stopper阻擋器 glove(s)手套 iudustrial alcohol工業酒精 sweeper掃把 mop拖把 vaccum cleaner吸塵器 rag 抹布 garbage container灰箕 garbage can垃圾箱 garbage bag垃圾袋 chain鏈條 jack升降機 production line流水線 to mop the floor拖地 to clean the

6、 floor掃地 to clean a table擦桌子 air pipe 氣管 packaging tool打包機 packaging打包 missing part漏件 excessive defects過多的缺陷 critical defect極嚴重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合規格 dimension/size is a little bigger尺寸偏大(小) slipped screwhead/slippery screw head螺絲滑頭 speckle斑點 mildewed=moldy=mould

7、y發霉 rust生銹 deformation變形 burr(金屬)flash(塑件)毛邊 grease/oil stains油污 inclusion雜質 shrinking/shrinkage縮水 mixed color雜色 scratch劃傷 painting make-up補漆 discoloration羿色 water spots水漬 polishing/surface processing表面處理 exposed metal/bare metal金屬裸露 lack of painting烤漆不到位 safety安全 quality品質 delivery deadline交貨期 cost

8、成本 engineering工程 enterprise plan = enterprise expansion projects企劃 QC品管 production, to produce生產 equipment設備 to start a press開機 stop/switch off a press關機 classification整理 regulation整頓 cleanness清掃 conservation清潔 qualified products, up-to-grade products良品 defective products, not up-to-grade products不良

9、品 waste廢料 feeder送料機 sliding rack滑料架 packing material包材 isolating plate baffle plate; barricade隔板 carton box紙箱 to pull and stretch拉深 to put material in place, to cut material, to compress, compressing壓縮 to feed, feeding送料 transportation運輸 (be)qualfied, up to grade合格 not up to grade, not qualified不合格

10、material change, stock change材料變更 evaluation評估 prepare for, make preparations for 準備 parameters參數 rotating speed, revolution轉速 manufacture management制造管理 abnormal handling異常處理 production unit生產單位 lots of production生產批量 steel plate鋼板 roll material卷料 to revise, modify修訂 to switch over to, switch-to th

11、row-over switching over切換 stage die工程模 automation自動化 to stake, staking, reviting鉚合 add lubricating oil加潤滑油 argon welding氬焊 vocabulary for stamping 沖壓常詞匯 stamping, press沖壓 punch press, dieing out press沖床 uncoiler & strainghtener整平機 feeder送料機 rack, shelf, stack料架 cylinder油缸 robot機械手 taker取料機 conve

12、yer belt輸送帶 transmission rack輸送架 one stroke一行程 inch寸動 to continue, cont.連動 to grip(material)吸料 location lump, locating piece, block stop 定位塊 reset復位 smoothly順利 filings鐵削 to draw holes抽孔 inquiry, search for查尋 to stock, storage, in stock庫存 receive領取 approval examine and verify審核 processing, to process

13、加工 delivery, to deliver 交貨 to return delivenry to. to send delinery back to retrn of goods退貨 registration登記 registration card登記卡 to control管制 to put forward and hand in提報 safe stock安全庫存 acceptance = receive驗收 to notice通知 application form for purchase請購單 consume, consumption消耗 to fill in填寫 abrasion磨損

14、 reverse angle = chamfer倒角 character die字模 to collect, to gather收集 failure, trouble故障 statistics統計 demand and supply需求 career card履歷卡 to take apart a die卸下模具 to load a die裝上模具 to tight a bolt擰緊螺栓 to looser a bolt擰松螺栓 easily damaged parts易損件 standard parts標準件 breaking.(be)broken,(be)cracked 斷裂 to lub

15、ricate潤滑 common vocabulary for die engineering模具工程常用詞匯 die 模具 punched hole沖孔 panel board鑲塊 to cutedges=side cut=side scrap切邊 to bending折彎 to pull, to stretch拉伸 Line streching, line pulling線拉伸 engraving, to engrave刻印 upsiding down edges翻邊 to stake鉚合 designing, to design設計 design modification設計變化 die

16、block模塊 folded block折彎塊 sliding block滑塊 location pin定位銷 lifting pin頂料銷 die plate, front board模板 padding block墊塊 stepping bar墊條 spring 彈簧 bolt螺栓 document folder文件夾 file folder資料夾 to put file in order整理資料 equipment設備 waste materials廢料 casing = containerazation裝箱 the first page第一聯 end-user/using unit(d

17、epartment)使用單位 summary of year-end physical inventory bills 年終盤點截止單據匯總表 bill name單據名稱 plate電鍍 mold成型 material for engineering mold testing工程試模材料 sample樣品 incoming material to be inspected進貨待驗 description品名 steel/rolled steel鋼材 material statistics sheet 物料統計明細表 meeting minutes會議記錄 meeting type 會別 dis

18、tribution department分發單位 location地點 chairman主席 present members出席人員 subject主題 conclusion結論 decision items決議事項 responsible department負責單位 pre-fixed finishing date預定完成日 approved by / checked by / prepared by核準/審核/承辦 revision版次 remark備注 production control confirmation生產確認 checked by初審 approved by核準 depa

19、rtment部門 on-hand inventory現有庫存 available material良品可使用 to be inspected or reworked 待驗或重工 total合計 cause description原因說明 part number/ P/N 料號 type形態 item/group/class類別 quality品質 prepared by制表 notes說明 cause analysis原因分析 raw materials原料 materials物料 finished product成品 semi-finished product半成品 packing mate

20、rials包材 good product/accepted goods/ accepted parts/good parts良品 defective product/non-good parts不良品 disposed goods處理品 warehouse/hub倉庫 skid/pallet棧板 tox machine自鉚機 wire EDM線割 EDM放電機 coil stock卷料 sheet stock片料 tolerance工差 score=groove壓線 cam block滑塊 expansion dwg展開圖 radius半徑 shim(wedge)楔子 torch-flame

21、cut火焰切割 stop pin定位銷 stock locater block定位塊 active plate活動板 baffle plate擋塊 cover plate蓋板 bushing block襯套 insert 入塊 capability能力 parameter參數 factor系數 alkalidipping脫脂 demagnetization去磁;消磁 high-speed transmission高速傳遞 heat dissipation熱傳 rack上料 degrease脫脂 rinse水洗 Chromate鉻酸處理 Anodize陽性處理 seal封孔 part numbe

22、r/P/N料號 good products良品 scraped products報放心品 defective products不良品 finished products成品 disposed products處理品 barcode條碼 flow chart流程表單 assembly組裝 stamping沖壓 molding成型 coordinate座標 auxiliary fuction輔助功能 heater band 加熱片 thermocouple熱電偶 sand blasting噴沙 grit 砂礫 derusting machine除銹機 degate打澆口 dryer烘干機 indu

23、ction感應 induction light感應光 response=reaction=interaction感應 ram連桿 concave凸 convex凹 nick缺口 speck瑕? shine亮班 splay 銀紋 gas mark焦痕 delamination起鱗 cold slug冷塊 blush 導色 gouge溝槽;鑿槽 satin texture段面咬花 patent專利 grit沙礫 granule=peuet=grain細粒 grit maker抽粒機 cushion緩沖 magnalium鎂鋁合金 magnesium鎂金 metal plate鈑金 lathe車 m

24、ill銼 plane刨 grind磨 drill鋁 boring鏜 blinster氣泡 fillet鑲;嵌邊 through-hole form通孔形式 voller pin formality滾針形式 cam driver鍘楔 shank摸柄 crank shaft曲柄軸 augular offset角度偏差 velocity速度 production tempo生產進度現狀 torque扭矩 spline=the multiple keys花鍵 quenching淬火 tempering回火 annealing退火 carbonization碳化 alloy合金 tungsten hig

25、h speed steel鎢高速的 moly high speed steel鉬高速的 organic solvent有機溶劑 liaison聯絡單 volatile揮發性 resistance電阻 ion離子 beacon警示燈 coolant冷卻液 crusher破碎機 模具工程類 plain die簡易模 pierce die沖孔模 forming die成型模 progressive die連續模 gang dies復合模 shearing die剪邊模 riveting die鉚合模 pierce沖孔 forming成型(抽凸,沖凸) draw hole抽孔 bending折彎 tr

26、im切邊 emboss凸點 dome凸圓 semi-shearing半剪 stamp mark沖記號 deburr or coin壓毛邊 punch riveting沖壓鉚合 side stretch側沖壓平 reel stretch卷圓壓平 groove壓線 blanking下料 stamp letter沖字(料號) shearing剪斷 tick-mark nearside正面壓印 tick-mark farside反面壓印 沖壓名稱類 extension dwg展開圖 procedure dwg工程圖 die structure dwg模具結構圖 material材質 material

27、thickness料片厚度 factor系數 upward向上 downward向下 press specification沖床規格 burr毛邊 gap間隙 weight重量 total wt.總重量 五金零件類 inner guiding post導柱 inner hexagon screw六角螺釘 dowel pin固定銷 coil spring彈簧 lifter pin頂料銷 pin銷 wire spring圓線彈簧 stop screw止付螺絲 located pin定位銷 outer bush外導套 模板類 top plate上托板（頂板） top block上墊腳 punch p

28、ad上墊板 punch holder上夾板 stripper pad脫料背板 up stripper上脫料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板 lower plate下模板 die pad下墊板 die holder下夾板 die set下模座 bottom block下墊腳 bottom plate下托板(底板) stripping plate外打(脫料板) outer stripper外脫料板 inner stripper脫料板 lower stripper下脫料板 零件類punch沖頭 insert

29、入塊(嵌入件) deburring punch壓毛邊沖子 groove punch壓線沖子 stamped punch字模沖子 round punch圓沖子 special shape punch異形沖子 bending block折刀 roller滾軸 baffle plate擋塊 located block定位塊 supporting block for location 定位支承塊 air cushion plate氣墊板 air-cushion eject-rod氣墊頂桿 trimming punch切邊沖子 stiffening rib punch = stinger 加強筋沖子 r

30、ibbon punch壓筋沖子 reel-stretch punch卷圓壓平?jīng)_子 guide plate定位板 sliding block滑塊 sliding dowel block滑塊固定塊 active plate活動板 lower sliding plate下滑塊板 upper holder block上壓塊 upper mid plate上中間板 spring box彈簧箱 spring-box eject-rod彈簧箱頂桿 spring-box eject-plate彈簧箱頂板 bushing bolck襯套 cover plate蓋板 guide pad導料塊 塑件&模具相

31、關英文 compre sion molding壓縮成型 flash mold溢流式模具 plsitive mold擠壓式模具 split mold分割式模具 cavity型控 母模 core模心 公模 taper錐拔 leather cloak仿皮革 shiver飾紋 flow mark流痕 welding mark溶合痕 post screw insert螺紋套筒埋值 self tapping screw自攻螺絲 striper plate脫料板 piston活塞 cylinder汽缸套 chip細碎物 handle mold手持式模具 移轉成型用模具encapsulation moldin

32、g低壓封裝成型 射出成型用模具 two plate兩極式（模具） well type蓄料井 insulated runner絕緣澆道方式 hot runner熱澆道 runner plat澆道模塊 valve gate閥門澆口 band heater環帶狀的電熱器 spindle閥針 spear head刨尖頭 slag well冷料井 cold slag冷料渣 air vent排氣道 h=0.020.05mm w=3.2mm L=35mm welding line熔合痕 eject pin頂出針 knock pin頂出銷 return pin回位銷反頂針 sleave套筒 stripper

33、plate脫料板 insert core放置入子 runner stripper plate澆道脫料板 guide pin導銷 eject rod (bar)（成型機）頂業捧 subzero深冷處理 three plate三極式模具 runner system澆道系統 stress crack應力電裂 orientation定向 sprue gate射料澆口，直澆口 nozzle射嘴 sprue lock pin料頭鉤銷(拉料桿) slag well冷料井 side gate側澆口 edge gate側緣澆口 tab gate搭接澆口 film gate薄膜澆口 flash gate閘門澆口

34、slit gate縫隙澆口 fan gate扇形澆口 dish gate因盤形澆口 H=F=1/2t1/5t T=2.53.5mm diaphragm gate隔膜澆口 ring gate環形澆口 subarine gate潛入式澆口 tunnel gate隧道式澆口 pin gate針點澆口 0.81.0mm Runner less無澆道 (sprue less)無射料管方式 long nozzle延長噴嘴方式 sprue澆口;溶渣 品質人員名稱類 QC quality control 品質管理人員 FQC final quality control 終點品質管制人員 IPQC in pro

35、cess quality control 制程中的品質管制人員 OQC output quality control 最終出貨品質管制人員 IQC incoming quality control 進料品質管制人員 TQC total quality control 全面質量管理 POC passage quality control 段檢人員 QA quality assurance 質量保證人員 OQA output quality assurance 出貨質量保證人員 QE quality engineering 品質工程人員 品質保證類 FAI first article inspec

36、tion 新品首件檢查 FAA first article assurance 首件確認 TVR tool verification report 模具確認報告 3B 3B 模具正式投產前確認 CP capability index 能力指數 CPK capability index of process 模具制程能力參數 SSQA standardized supplier quality 合格供應商品質評估 OOBA out of box audit 開箱檢查 QFD quality function deployment 品質機能展開 FMEA failure model effecti

37、veness analysis 失效模式分析 8 disciplines 8項回復容 FA final audit 最後一次稽核 CAR corrective action request 改正行動要求 corrective action report 改正行動報告 FQC運作類AQL Acceptable Quality Level 運作類允收品質水準 S/S Sample size 抽樣檢驗樣本大小 ACC Accept 允收 REE Reject 拒收 CR Critical 極嚴重的 MAJ Major 主要的 MIN Minor 輕微的 AOQ Average Output Qual

38、ity 平均出廠品質 AOQL Average Output Quality Level 平均出廠品質 Q/R/S Quality/Reliability/Service 品質/可靠度服務 MIL-STD Military-Standard 軍用標準 S I-S IV Special I-Special IV 特殊抽樣水準等級 P/N Part Number 料號 L/N Lot Number 特采 AOD Accept On Deviation 特采 UAI Use As It 首件檢查報告 FPIR First Piece Inspection Report 百萬分之一 PPM Perce

39、nt Per Million 批號 制程統計品管專類 SPC Statistical Process Control 統計制程管制 SQC Statistical Quality Control 統計品質管制 R Range 全距 AR Averary Range 全距平均值 UCL Upper Central Limit 管制上限 LCL Lower Central Limit 管制下限 MAX Maximum 最大值 MIN Minimum 最小值 GRR Gauge Reproducibility&Repeatability 量具之再制性與重測性判斷量可靠與否 DIM Dimen

40、sion 尺寸 DIA Diameter 直徑 FREQ Frequency 頻率 N Number 樣品數 其它品質術語類QCC Quality Control Circle 品質圈 QIT Quality Improvement Team 品質改善小組 PDCA Plan Do Check Action 計劃 執行 檢查 總結 ZD Zero Defect 零缺點 QI Quality Improvement 品質改善 QP Quality Policy 目標方針 TQM Total Quality Management 全面品質管理 MRB Material Reject Bill 退貨

41、單 LQL Limiting Quality Level 最低品質水準 RMA Return Material Audit 退料認可 QAN Quality Amelionrate Notice 品質改善活動 ADM Absolute Dimension Measuremat 全尺寸測量 QT Quality Target 品質目標 7QCTools 7 Quality Controll Tools 品管七大手法 通用之件類 ECN Engineering Change Notes 工程變更通知(供應商) ECO Engineering Change Order 工程改動要求(客戶) PCN

42、Process Change Notice 工序改動通知 PMP Product Management Plan 生產管制計劃 SIP Specification In Process 制程檢驗規格 SOP Standard Operation Procedure 制造作業規 IS Inspection Specification 成品檢驗規 BOM Bill Of Material 物料清單 PS Package Specification 包裝規 SPEC Specification 規格 DWG Drawing 圖面 系統文件類QC Quality System 品質系統 ES Engi

43、neering Standarization 工程標準 CGOO China General PCE廠文件 H Huston (美國)休斯敦 C Compaq (美國)康伯公司 C China 中國大陸 A Assembly 組裝(廠) S Stamping 沖壓(廠) P Painting 烤漆(廠) I Intel 英特爾公司 T TAIWAN IWS International Workman Standard 工藝標準 ISO International Standard Organization 國際標準化組織 GS General Specification 一般規格 CMCS C

44、-China M-Manufact C-Compaq S-Stamping Compaq產品在沖壓廠制造作業規 CQCA Q-Quality A-Assembly Compaq產品在組裝廠品管作業規 CQCP P-Painting Compaq產品在烤漆廠品管作業規 部類 PMC Production & Material Control 生產和物料控制 PPC Production Plan Control 生產計劃控制 MC Material Control 物料控制 ME Manafacture Engineering 制造工程部 PE Project Engineering 產

45、品工程部 A/C Accountant Dept 會計部 P/A Personal & Administration 人事行政部 DC Document Center 資料中心 QE Quality Engineering 品質工程(部) QA Quality Assurance 品質保證(處) QC Quality Control 品質管制(課) PD Product Department 生產部 LAB Labratry 實驗室 IE Industrial Engineering 工業工程 R&D Research & Design 設計開發部 P Painting

46、 烤漆(廠) A Asssembly 組裝(廠) S Stamping 沖壓(廠) 生產類PCS Pieces 個(根,塊等) PRS Pairs 雙(對等) CTN Carton 卡通箱 PAL Pallet/skid 棧板 PO Purchasing Order 采購訂單 MO Manufacture Order 生產單 D/C Date Code 生產日期碼 ID/C Identification Code (供應商)識別碼 SWR Special Work Request 特殊工作需求 L/N Lot Number 批號 P/N Part Number 料號 其它OEM Origina

47、l Equipment Manufacture 原設備制造 PCE Personal Computer Enclosure 個人電腦外設 PC Personal Computer 個人電腦 CPU Central Processing Unit 中央處理器 SECC SECC 電解片 SGCC SGCC 熱浸鍍鋅材料 NHK North of Hongkong 中國大陸 PRC People's Republic of China 中國大陸 U.S.A the United States of America 美國 A.S.A.P As Soon As Possible 盡可能快的 E

48、-MAIL Electrical-Mail 電子 N/A Not Applicable 不適用 QTY Quantity 數量 VS 以與 REV Revision 版本 JIT Just In Time 零庫存 I/O Input/Output 輸入/輸出 OK Ok 好 NG Not Good 不行,不合格 C=0 Critical=0 極嚴重不允許 ESD Electry-static Discharge 靜電排放 5S 希臘語 整理,整頓,清掃,清潔,教養 ATIN Attention 知會 CC Carbon Copy 副本復印相關人員 APP Approve 核準,認可,承認 CH

49、K Check 確認 AM Ante Meridian 上午 PM Post Meridian 下午 CD Compact Disk 光碟 CD-ROM Compact Disk Read-Only Memory 只讀光碟 FDD Floppy Disk Drive 軟碟機 HDD Hard Disk Drive 碟碟機 REF Reference 僅供參考 CONN Connector 連接器 CAV Cavity 模穴 CAD Computer Aid Design 計算機輔助設計 ASS'Y Assembly 裝配,組裝 MAT'S Material 材料 IC Inte

50、grated Circuit 集成電路 T/P True Position 真位度 TYP Type 類型 WDR Weekly Delivery Requitement 周出貨需求 C?T Cycle Time 制程周期 L/T Lead Time 前置時間(生產前準備時間) S/T Standard Time 標準時間 P/M Product Market 產品市場 3C Computer,Commumcation,Consumer electronic's 消費性電子 5WIH When,Where,Who,What,Why,How to 5M Man,Machine,Mater

51、ial,Method,Measurement 4MIH Man,Materia,Money,Method,Time 人力,物力,財務,技術,時間(資源) SQA Strategy Quality Assurance 策略品質保證 DQA Desigh Quality Assurance 設計品質保證 MQA Manufacture Quality Assurance 制造品質保證 SSQA Sales and service Quality Assurance 銷售與服務品質保證 LRR Lot Rejeet Rate 批退率 BS Brain storming 腦力激蕩 EMI Electr

52、onic Magnetion Inspect 高磁測試 FMI Frequency Modulatim Inspect 高頻測試 B/M Boar/Molding(flat cable) C/P Connector of PC A/P Assembly SPS Switching power supply 電源箱 DT Desk Top 臥式(機箱) MT Mini-Tower 立式(機箱) DVD Digital Vedio Disk VCD Vdeio Compact Disk LCD Liquid Crystal Display CAD Computer AID Design CAM C

53、omputer AID Manufacturing CAE Computer AID Engineering ABIOS Achanced Basic in put/output system 先進的基本輸入/輸出系統 CMOS Complemeruary Metoll Oxide Semiconductor 互補金屬氧化物半導體 PDA Personal Digital Assistant 個人數字助理 IC Integrated Circuit 集成電路 ISA Industry Standard Architecture 工業標準體制結構 MCA Micro Channel Architecture 微通道結構 EISA Extended Industry Standard Architecture 擴充的工業標準結構 SIMM Single in-line memory module 單項導通匯流組件 DIMM Dual in-line Memory Module 雙項導通匯流組件 LED Light-Emi