模具常用術語中英文對照表

1、R，L Co.,Ltd模具常用術語中英文對照模芯Parting Core偏移量Offset局部視圖Partial View水塞Water Line Plug冷料#Cold Slag撬模腳Ppy Slot線切割Wire E.D.M重新加工Reworked輪廊Contour配件Components螺紋孔Tapping Hole補償Compensation連接件Fittings平面度Parallel斜針Angle Pin倒角Chamfer接合Engage模胚Mold Base替換鑲件Interchangeable Mold Inserts熱嘴Hotnozzle指定噸位的注塑機Specific Pre

2、ss火花機Edm水嘴接頭Water Fittings熔接線Weildline螺紋Eyebolt Thread壓機Press回針Stop Pin曬紋Texturing二級頂出針Sub-Leaderd Pin梯形Trapezoid鑲件Mold Insert凸緣、法蘭Flange加硬Harden方鐵Spacer Block唧嘴Sprue頂針板Ejector Plate設計筒圖Design Preliminary頂針底板Ejector Retainer Plate名稱塊表Title Block墊板Retainer Plate版本標識Revision Level后模鑲針Core Pin材料清單Stock

3、 List拉圾釘Stop Pin制模Build Mold有托頂針Shoulder Ejector Pin手動滑塊Hand Slide頂針板導套Guided Ejection Bushing漏水測試Leak Test針板導柱Guided Ejection Leader Pin流道排氣Runner Vents唧嘴Sprue Bushing拋光Draw Polish三板模延伸式唧嘴Extension Nozzle Bushing側抽芯Side Action水口板導套Runner Stripper Plate Bushing加強筋Reinforcing定位圈（法蘭）Locating Ring三角撐Gu

4、sset管釘（定位銷）Dowel Pin柱子Bossed管狀管釘Tubular Dowel出模斜度Draft吊環Safety Hoist Ring外廊Contour日期印Dating Insert落單會議Kick-Off Meeting環保印Recycling Insert裝卸孔Handling Hole氣頂Air Poppet Valve運輸安全帶Moldstrap截水口鑲件Runner Shut-Off Insert碼模槽Clamp Slot早回Early Ejector Return撐頭Support Pillar加速項Accelerated Ejector螺牙1/2-13 Eye Bo

5、lt 1/2-13Tap客戶Client導柱位Leader Pin Location產品名Part Name耐落膠Teflon Paste產品編號Part No縮水Shrinkage版本Rev模胚Mold Base下模鑲件Core Block上模鑲件Cavity Block小鑲件Sub-Insert下模小鑲件Core Sub-Insert上模小鑲件CavitySub-Insert行位Slide行位鑲件Slide Insert壓條Gib壓緊塊（鏟機）Jaw硬片（摩擦片）Wear Plate水口鐵Runner Bar上模水口鐵Upper RunnerBar下模水口鐵Lower Runner Bar

6、彈簧Spring水口勾針Sprue Puller Pin頂針Ejector Pin撐頭Support Pillar直身鎖Side Lock斜度鎖Interlock鎖模板Safety Bar O令（密封圈）ORing喉塞Plug隔水片Baffle波子螺絲（行位定位螺絲）Ball-Catch斜頂Lifter控制開關Switch回針Return Pin斜導柱Angle Pin推板Stripper PlateA板APlateB 板BPlate方鐵（墊鐵）Spacer Block頂針板EjectorPlate頂針底板Ejector Retainer Plate墊板Retainer Plate垃圾釘Sto

7、p Pin有托頂針Shoulder Ejector Pin頂針板導套Guided Ejection Bushing針板導柱Guided Ejection Leader Pin唧嘴Sprue Bushing三板模延伸式唧嘴Extension Nozzle Bushing水口板導套Runner Stripper Plate Bushing定位圈（法蘭）Locating Ring管釘（定位銷）Dowel Pin管狀管釘Tubular Dowel吊環Safety Hoist Ring日期印Dating Insert環保印Recycling Insert氣頂Air Poppet Valve截水口鑲件Ru

8、nner Shut-Off Insert早回Early Ejector Return加速頂Accelerated Ejector扁頂Blade出模斜波Draft手動滑塊模具Hand Slide-In Type Mold回針板Backup合模Shutoff空隙槽Clearance Slot導柱及導套Leader Pin Bushing水口拉鉤Spuer Puller模框鑲件Pocket Insert成型熱固性塑膠模具Thermoset Mold三板模3-Plat Mold分型面Parting Line司筒Ejector Sleeve墊圈Washer熔接線（夾水紋）Weldline吸針Sucker

9、 Pin回針板Retainer Plate頂出板Knock -Out Plate電動安全開關Electrical-Safety Switch脫開CutOf Position預先決定Preload緩沖器Bumper襯墊Cushion公差Tolerance突然性動作Slam銷針Dowel鉤槽Gib精磨Finished通框Through Window粘后模Sticking Core粘水口Sticking Sprue夾水紋Weld Line變形Warpage走水不平均Filling Uneven拋光Polishing走不齊Short Shot蝕紋Texture掛成品Part Hanging探熱針The

10、rmocouple漏水Water Leakage三打螺絲毫（限螺絲)Stripper Bolt刮花（擦傷）Galling蓋板Cover Plate漏電Ele Leakage齒輪Gear困氣Air Trapping油唧Hydraulic Cylinder溫度Temperature司筒Ejector Sleeve注塑模Injection Mold導柱Leader Pin入水Gate冷料#Cold Slag試板Sampling線切割Wire E.D.M.壓力Pressure輪廓Contour倒圓Fillet螺紋孔Tapping Hole頂棍Ejector連接件Fittings頂白Stress Mar

11、k斜針Angle Pin粘前模Sticking Cav接合Engage名稱塊表Title Block替換鑲件Interchangeable Mold Inserts版本標識Revision Level指定噸位的注塑機Specific Press材料清單Stock List水嘴接頭Water Fittings斜導柱（斜邊）Angle Pin螺紋Eyebolt ThreadA板Aplate回針Stop PinB板Bplate二級頂出針Sub-Leader Pin倒扣Under-Cut鑲件Mold Insert披峰Flash鎖定位Lock縮水Sink Mark楔子（鏟雞） Wedge氮化Nitride高產量模量High Volume Running Mold不規則四邊形Trapezoid剖面圖Cross Section縮水Shrinkage模具結構Mold Construction連續的Consecutive模芯Parting Core雕刻Engrave局部視圖Partial View出模角Draft熱流道Manifold分模面Parting Surface熱嘴Hot Nozzle擦位Shut-Off(S/0)型腔數Cav No導套Bushing模號Mold N