美國FDA分析方法驗證指南中英文對照

1、美國FDA分析方法驗證指南中英文對照I. INTRODUCTIONThis guidance provides recommendations to applicants on submitting analytical procedures, validation data, and samples to support the documentation of the identity, strength, quality, purity, and potency of drug substances and drug products.1. 緒論本指南旨在為申請者提供建議，以幫助其提交分

2、析方法，方法驗證資料和樣品用于支持原料藥和制劑的認定，劑量，質量，純度和效力方面的文件。This guidance is intended to assist applicants in assembling information, submitting samples, and presenting data to support analytical methodologies. The recommendations apply to drug substances and drug products covered in new drug applications (NDAs), a

3、bbreviated new drug applications (ANDAs), biologics license applications (BLAs), product license applications (PLAs), and supplements to these applications.本指南旨在幫助申請者收集資料，遞交樣品并資料以支持分析方法。這些建議適用于NDA，ANDA，BLA，PLA及其它們的補充中所涉及的原料藥和制劑。The principles also apply to drug substances and drug products covered i

4、n Type II drug master files (DMFs). If a different approach is chosen, the applicant is encouraged to discuss the matter in advance with the center with product jurisdiction to prevent the expenditure of resources on preparing a submission that may later be determined to be unacceptable.這些原則同樣適

5、用于二類DMF所涉及的原料藥和制劑。如果使用了其它方法，鼓勵申請者事先和FDA藥品評審中心的官員進行討論，以免出現這種情況，那就是花了人力物力所準備起來的遞交資料后來發現是不可用的。The principles of methods validation described in this guidance apply to all types of analytical procedures. However, the specific recommendations in this guidance may not be applicable to certain unique analy

6、tical procedures for products such as biological, biotechnological, botanical, or radiopharmaceutical drugs.本指南中所述的分析方法驗證的原則適用于各種類型的分析方法。但是，本指南中特定的建議可能不適用于有些產品所用的特殊分析方法，如生物藥，生物技術藥，植物藥或放射性藥物等。For example, many bioassays are based on animal challenge models, 39 immunogenicity assessments, or other imm

7、unoassays that have unique features that should be considered when submitting analytical procedure and methods validation information.比如說，許多生物分析是建立在動物挑戰模式，免疫原性評估或其它有著獨特特性的免疫分析基礎上的，在遞交分析方法和分析方法驗證資料時需考慮這些獨特的性質。Furthermore, specific recommendations for biological and immunochemical tests that may be ne

8、cessary for characterization and quality control of many drug substances and drug products are beyond the scope of this guidance document.而且，許多原料藥和制劑的界定和質量控制所需的生物和免疫化學檢測并不在本指南的范圍之內。Although this guidance does not specifically address the submission of analytical procedures and validation data for ra

9、w materials, intermediates, excipients, container closure components, and other materials used in the production of drug substances and drug products, validated analytical procedures should be used to analyze these materials.盡管本指南并不專門敘述原料，中間體，賦形劑，包裝材料及原料藥和制劑生產中所用的其它物料的分析方法及分析方法驗證資料的遞交，但是應該應用驗證過的分析方法

10、來分析檢測這些物質。For questions on appropriate validation approaches for analytical procedures or submission of information not addressed in this guidance, applicants should consult with the appropriate chemistry review staff at FDA.對于本指南中未提及的關于分析方法驗證和資料提交方面的問題，請向FDA相關的化學評審人員咨詢。This guidance, when finalized

11、, will replace the FDA guidance for industry on Submitting Samples and Analytical Data for Methods Validation (February 1987).本指南，一旦定稿，將取代FDA于1987年2月份發布的工業指南：分析方法驗證所需提交的樣品和分析資料。II. BACKGROUND Each NDA and ANDA must include the analytical procedures necessary to ensure the identity, strength, quality

12、, purity, and potency of the drug substance and drug product, including bioavailability of the drug product (21 CFR 314.50(d)(1) and 314.94(a)(9)(i). II. 背景每個NDA和ANDA都必需包括必要的分析方法以確保原料藥和制劑的認定，劑量，質量，純度和效力，還包括制劑的生物利用度(21 CFR 314.50(d)(1) 和314.94(a)(9)(i)。FDA驗證文件現場備查，可以不與DMF一起交。Data must be available to

13、 establish that the analytical procedures used in testing meet proper standards of accuracy and reliability (21 CFR 211.165(e) and 211.194(a)(2).必須要有資料來論證所用的分析方法是符合一定的準確度和可靠性標準的。Methods validation is the process of demonstrating that analytical procedures are suitable for their intended use. The met

14、hods validation process for analytical procedures begins with the planned and systematic collection by the applicant of the validation data to support the analytical procedures.分析方法驗證是論證某一分析方法適用于其用途的過程。分析方法的驗證過程是從申請者有計劃地系統性收集驗證資料以支持分析方法開始的。Thereview chemist evaluates the analytical procedures and va

15、lidation data submitted in the NDA or ANDA. 審評化學家會對NDA或ANDA中的分析方法和驗證資料進行評審。On request from FDA, an NDA or ANDA applicant must submit samples of drug product, drug substance, noncompendial reference standards, and blanks so that the applicant's drug substance and drug product analytical procedure

16、s can be evaluated by FDA laboratories (21 CFR 314.50(e) and 314.94(a)(10).一旦FDA有要求，則NDA或ANDA的申請者必須提交制劑，原料藥，非藥典對照品和空白以使FDA實驗室能對申請者所用分析方法進行評審(21 CFR 314.50(e) and 314.94(a)(10)。The FDA laboratory analysis demonstrates that the analytical procedures are reproducible by laboratory testing. The review c

17、hemists and laboratory analysts determine the suitability of the analytical procedures for regulatory purposes.FDA實驗室的分析會論證該分析方法在實驗室內是可以重現的。審評化學家和實驗室分析家會從法規的角度確定該分析方法的適用性。FDA investigators inspect the analytical laboratory testing sites to ensure that the analytical procedures used for release and s

18、tability testing comply with current good manufacturing practices (CGMPs) (21 CFR part 211) or good laboratory practices (GLPs) (21 CFR part 58), as appropriate.FDA檢查官會對分析實驗室進行檢查確保用于放行和穩定性實驗的分析方法符合現行的GMP（21CFR part 211)和GLP (21 CFR part 58)。Each BLA and PLA must include a full description of the man

19、ufacturing methods, including analytical procedures, that demonstrate that the manufactured product meets prescribed standards of safety, purity, and potency (21 CFR 601.2(a) and 601.2(c)(1)(iv).每個BLA和PLA都必須要有詳細的生產工藝描述，包括分析方法，以說明所生產的產品是符合規定睥安全，純充和效力標準的(21 CFR 601.2(a) and 601.2(c)(1)(iv)。Data must b

20、e available to establish that the analytical procedures used in testing meet proper standards of accuracy and reliability (21 CFR 81211.194(a)(2). For BLAs, PLAs, and their supplements, the analytical procedures and their validation are submitted as part of the license application or supplement and

21、are evaluated by the review committee.必須要有資料證明所用的分析方法是符合一定的準確度和可靠性要求的(21 CFR 81211.194(a)(2)。對于BLA，PLA及它們的補充，在所提交的許可證申請中應當要有分析方法和方法驗證這部分的資料，審評委員會會對這部分資料進行評審。Representative samples of the product must be submitted and summaries of results of tests performed on the lots represented by the submitted sa

22、mple must be provided (21 CFR 601.2(a) and 601.2(c)(1)(vi). The review committee chair may request analytical testing by CBER laboratory analysts to evaluate the applicant=s analytical procedures and verify the test results.需提供代表性樣品及該樣品所代表批號的檢測結果總結(21 CFR 601.2(a) and 601.2(c)(1)(vi)。評審委員會主席會要求CBER實

23、驗室的分析人員進行分析實驗對申請者的分析方法進行評估，并確認其分析結果。All analytical procedures are of equal importance from a validation perspective. In general, validated analytical procedures should be used, irrespective of whether they are for in-process, release, acceptance, or stability testing. Each quantitative analytical pr

24、ocedure should be designed to minimize assay variation.從驗證的角度來看，所有的分析方法有著同樣的重要性。一般來說，應當要應用已驗證過的分析方法，而不論其是被用于過程控制，放行，合格或穩定性實驗。高等每個定量分析方法時都應當要減少其分析誤差。Analytical procedures and validation data are submitted in the sections of the application on analytical procedures and controls. Recommendations on inf

25、ormation to be submitted are included in sections III through IX and XI of this guidance. Information on submission of the methods validation package to the NDA or ANDA and samples to the FDA laboratories is provided in section X.分析方法和驗證資料應當擺在申請的分析方法和控制章節中提交。本指南的第III到IX章和XI章給出了所需提供資料方面的建議。向FDA實驗室提供樣

26、品和遞交NDA和ANDA中的分析方法驗證資料的信息見第X章。III. TYPES OF ANALYTICAL PROCEDURES A. Regulatory Analytical Procedure A regulatory analytical procedure is the analytical procedure used to evaluate a defined characteristic of the drug substance or drug product. The analytical procedures in the U.S. Pharmacopeia/Natio

27、nal Formulary (USP/NF) are those legally recognized under section 501(b) of the Food, Drug, and Cosmetic Act (the Act) as the regulatory analytical procedures for compendial items. For purposes of determining compliance with the Act, the regulatory analytical procedure is used.III分析方法的類型A. 法定分析方法法定分

28、析方法是被用來評估原料藥或制劑的特定性質的。USP/NF中的分析方法是法定的用于藥典項目檢測的分析方法。為了確認符合法規，需使用法定分析方法。B. Alternative Analytical Procedure An alternative analytical procedure is an analytical procedure proposed by the applicant for use instead of the regulatory analytical procedure. A validated alternative analytical procedure sho

29、uld be submitted only if it is shown to perform equal to or better than the regulatory analytical procedure.B. 替代分析方法替代分析方法是申請者提出用于代替法定分析方法的分析方法。只有當一替代分析方法相當于或優于法定分析方法時，才可以應用驗證過的替代分析方法。If an alternative analytical procedure is submitted, the applicant should provide a rationale for its inclusion and

30、 identify its use (e.g., release, stability testing), validation data, and comparative data to the regulatory analytical procedure.如果提交了替代分析方法，申請者還應當提供其理由，并標明其用途（如，放行，穩定性實驗），驗證資料及其與法定分析方法的對比資料。C. Stability-Indicating Assay A stability-indicating assay is a validated quantitative analytical procedure

31、 that can detect the changes with time in the pertinent properties of the drug substance and drug product. C. 穩定性指示分析穩定性指示分析是能檢測出原料藥或制劑的某些性質隨著時間的延長而出現的變化的定量分析方法。A stability-indicating assay accurately measures the active ingredients, without interference from degradation products, process impurities

32、, excipients, or other potential impurities。穩定性指示分析能不受降解產物，工藝雜質，賦形劑或其它潛在雜質的影響而準確測定其中的活性成分。If an applicant submits a non-stability-indicating analytical procedure for release testing, then an analytical procedure capable of qualitatively and quantitatively monitoring the impurities, including degrada

33、tion products, should complement it. Assay analytical procedures for stability studies should be stability-indicating, unless scientifically justified.如果申請者遞交了用于放行檢測的非穩定性指示分析方法，則應當要有能定性和定量地監測雜質，包括降解產物，的分析方法對其進行補充。穩定性試驗中所用的含量分析方法應當要有穩定性指示能力，除非有科學的理由能證明其合理性。IV. REFERENCE STANDARDS A. Types of Standard

34、s A reference standard (i.e., primary standard) may be obtained from the USP/NF or other official sources (e.g., CBER, 21 CFR 610.20). If there are questions on whether a source of a standard would be considered by FDA to be an official source, applicants should contact the appropriate chemistry rev

35、iew staff. When there is no official source, a reference standard should be of the highest possible purity and be fully characterized.IV 標準品A標準品的類型可以從USP/NF處或其它官方(比如說，CBER，21CFR 610.20)獲得標準品 (也就是一級對照品)。如果不能確定一標準品的來源是否會被FDA認為是官方來源，申請者應當要向適當?shù)幕瘜W(xué)評審人員咨詢。如果沒有官方來源，則被用來作標準品的物質應當要有盡可能高的純度，并得到充分界定。A working s

36、tandard (i.e., in-house or secondary standard) is a standard that is qualified against and used instead of the reference standard.工作對照品 (也就是內部標準品或二級標準品)是根據一級對照品標定的，并用來代替一級對照品的。B. Certificate of Analysis A certificate of analysis (COA) for reference standards from non-official sources should be submi

37、tted in the section of the application on analytical procedures and controls. For standards from official sources, the user should ensure the suitability of the reference standard. The standard should be stored correctly and used within the established use interval.B分析報告單對于非官方標準品，在申請的分析方法和控制章節中應當要提供

38、該標準品的分析報告單。對于從官方獲得的標準品，用戶應當要確保標準品的適用性。應當正確儲存標準品并在已確定的時間段內使用該標準品。C. Characterization of a Reference Standard Reference standards from USP/NF and other official sources do not require further characterization. A reference standard that is not obtained from an official source should be of the highest p

39、urity that can be obtained by reasonable effort, and it should be thoroughly characterized to ensure its identity, strength, quality, purity, and potency.C標準品的界定從USP/NF及其它官方來源獲得的標準品是不需要進一步界定的。非官方對照品要有盡可能高的純度，并進行充分地界定以確保其結構，劑量，質量，純度和效力。The qualitative and quantitative analytical procedures used to ch

40、aracterize a reference standard are expected to be different from, and more extensive than, those used to control the identity, strength, quality, purity, and potency of the drug substance or the drug product. Analytical procedures used to Draft Not for Implementation characterize a reference standa

41、rd should not rely solely on comparison testing to a previously designated reference standard.用于界定標準品的定性和定量分析方法應當要不同于用于控制原料藥或制劑的結構，劑量，質量，純度和效力的分析方法，要比它們更深入。用于標準品界定的分析方法不應僅僅是和先前的指定標準品進行比較實驗。Generally, this characterization information should include:  A brief description of the manufacture of th

42、e reference standard, if the manufacturing process differs from that of the drug substance. Any additional purification procedures used in the preparation of the reference standard should be described.一般來說，界定資料應當要包括：標準品的簡單工藝描述，如果其生產工藝是否于其相應的原料藥的話。應當要敘述制備標準品時所用的補充精制過程。Legible reproductions of the rel

43、evant spectra, chromatograms, thin-layer chromatogram (TLC) photographs or reproductions, and other appropriate instrumental recordings.  Data establishing purity. The data should be obtained by using appropriate tests, such as TLC, gas chromatography (GC), high-pressure liquid chromatography (

44、HPLC), phase solubility analysis, appropriate thermometric analytical procedures, and others as necessary.相關光譜圖，色譜圖，TLC照片及其它儀器輸出的清晰復印件。建立純度的資料。應當要應用適當?shù)臋z測方法來獲得這些資料，比如說TLC，GC，HPLC，相溶解分析，適當?shù)臒岱治龇椒捌渌匾姆治龇椒?。Appropriate chemical attribute information, such as structural formula, empirical formula, and mo

45、lecular weight. Information to substantiate the proof of structure should include appropriate analytical tests, such as elemental analysis, infrared spectrophotometry (IR), ultraviolet spectrophotometry (UV), nuclear magnetic resonance spectroscopy (NMR), and mass spectrometry (MS), as well as appli

46、cable functional group analysis. Detailed interpretation of the test data in support of the claimed structure should be provided.適當?shù)幕瘜W(xué)性質資料，比如結構式，經驗式和分子量等。結構確證資料應當要包括適當?shù)姆治鰷y(cè)試，比如元素分析，IR，UV,NMR和MS，及適用的官能團分析。還應當要提供具體的結構解析資料。A physical description of the material, including its color and physical form.

47、60; Appropriate physical constants such as melting range, boiling range, refractive index, dissociation constants (pK values), and optical rotation.  A detailed description of the analytical procedures used to characterize the reference standard.物理性質的描述，包括顏色和物理形態。 適當?shù)奈锢沓?shù)，比如說熔程，沸程，折射率，離解常數(pK值)

48、和旋光度。用于界定標準品的分析程序的詳細敘述。For biotechnological/biological product reference standards, the recommendations on characterization information above may apply and should be considered. However, additional and/or different tests would be important to assess physicochemical characteristics, structural charac

49、teristics, biological activity, and/or immunochemical activity.至于生物技術/生物產品的標準品，應當要考慮上述建議，可能可以應用。然而，其它確定物理化學性質，結構特性，生物活性和/或免疫化學活性的補充檢測和/或其它檢測將是非常重要的。Physicochemical determinations may include isoform, electrophoretic, and liquid chromatographic patterns, as well as spectroscopic profiles. Structural

50、characterization may include a determination of amino acid sequence, amino acid composition, peptide map, and carbohydrate structure. Biological and/or immunochemical activity should be assessed using the same analytical procedures used to determine product potency.物理化學性質包括異構體，電泳和液相色譜行為及光譜性質等。結構界定可能

51、包括氨基酸序列，氨基酸組成，縮氨酸圖和碳水結構。確定生物和/或免疫化學活性的分析方法應當要和用來確定產品效力的分析方法一樣。These can include animal-based, cell culture-based, biochemical, or ligand/receptor-binding assays. While these tests may be needed for complete characterization of certain reference standards, specific recommendations for validation of b

52、iological and immunochemical tests are not contained in this guidance document.這些分析方法可以包括基于動物的，細胞培養的，生物化學的或配位體/接受體螯合的分析方法。如果這些檢測需用于某些標準品的界定，生物和免疫化學檢測的分析方法驗證方面的特殊建議并不在本指南的范圍之內。V. METHODS VALIDATION FOR INDs For an investigational new drug, sufficient information is required in each phase of an invest

53、igation to ensure proper identification, quality, purity, strength, and/or potency. The amount of information on analytical procedures and methods validation necessary will vary with the phase of the investigation (21 CFR 312.23(a)(7).VIND中的分析方法驗證 對于IND而言，每個階段的研究都需要有足夠的資料以確保合適的認定，質量，純度，劑量和/或效力。

54、所需的分析方法和方法驗證方面的資料會隨著研究的階段變化而變化(21CFR312.23(a)(7)。For general guidance on analytical procedures and methods validation information to be submitted for phase 1 studies, sponsors should refer to the FDA guidance for industry on Content and Format of Investigational New Drug Applications (INDs) for Phas

55、e 1 Studies of Drugs, Including Well- Characterized, Therapeutic, Biotechnology-Derived Products (November 1995).關于在第1階段研究所需提交的分析方法和方法驗證資料方面的指南，發起人可以參考FDA的指南：藥品（包括結構確定的，有療效的，生物技術產品）第1階段研究的IND申請的內容和格式（1995年11月）。General guidance regarding analytical procedures and methods validation information to be

56、submitted for phase 2 or phase 3 studies will be provided in the FDA guidance for industry INDs for Phase 2 and 3 Studies of Drugs, Including Specified Therapeutic Biotechnology-Derived Products, Chemistry, Manufacturing, and Controls Content and Format, when finalized (draft guidance published Apri

57、l 1999).第2和第3階段研究所需提交的分析方法和方法驗證資料方面的指南，發起人將可以參考FDA的指南：藥品（包括結構確定的，有療效的，生物技術產品）第1階段研究的IND申請的CMC內容和格式（草案，1999年4月）。All analytical procedures should be fully developed and validation completed when the NDA, ANDA, BLA, or PLA is submitted.在遞交NDA，ANDA，BLA或PLA時，所有的分析方法都應當要開發出來，并得到驗證。VI. CONTENT AND FORMAT O

58、F ANALYTICAL PROCEDURES FOR NDAs, 230ANDAs, BLAs, AND PLAs Any analytical procedure submitted in an NDA, ANDA, BLA, or PLA should be described in sufficient detail to allow a competent analyst to reproduce the necessary conditions and obtain results comparable to the applicant=s. Aspects of the anal

59、ytical procedure that require special attention should be described.VINDA，ANDA，BLA和PLA中分析方法的內容和格式NDA，ANDA，BLA和PLA中所提交的任一分析方法都應當要有詳細的描述，以使合格的分析人員能重現出所需的實驗條件并獲得和申請者相當?shù)膶?shí)驗結果。應當要敘述分析方法中需要特殊注意的地方。If the analytical procedure used is in the current revision of the USP/NF or other FDA recognized standard references (e.g., AOAC International Book Of Methods) and the referenced analy