控制面板顯示故障信息對照表

1、面板信息對照表S100&S200-II機器級別代碼信息含義ALARMSA1Pressure over!排氣壓力過高A2moter over load!主電機過載A3Pressure Sen sor!壓力傳感器壞A4Temperature Sen sor!溫度傳感器壞A5Motor Rotatio n!主電機轉向反A6Starter fault 1M 3M接觸器1M或3M壞A7Starter fault 2M 1S接觸器 2M或1S壞A8Temperature over!排氣溫度過高A9Beari ng temp over!軸承回油溫度咼WARNINGW1Coolant Filter油過

2、濾器臟/堵W2Air Filter空濾器臟/堵W3Separater Filter油分離芯臟/堵STATUS1Pressure 0.80 Mpa排氣壓力2Temperature 92 c排氣溫度3Sump Pressure 0.82Mpa分離前壓力4Total Hours總運行時間Loaded Hours總加載運行時間5Error A1故障停機原因記錄380V-M250級別代碼信息含義ALARMSA1Pressure over壓力過高A2Fan moter over load風機電機過載A3Pressure Sen sor壓力傳感器壞A4Temperature Sen sor溫度傳感器壞A5P

3、ower phase fault電源相位反A6Starter fault MC接觸器 MC壞A7Starter fault SC DC接觸器 SC或DC壞A8Temperature over排氣溫度過高A9Beari ng temp over軸承回油溫度咼A10Volt Error -check ing電源電壓不穩A11Motor over load主電機過載A12Motor beari ng hot主電機軸承過熱A13Remote stop fault遠控-停機故障A14Remote start fault遠控-啟動故障A15Fan con tactor fault風機接觸器壞WARNING

4、W1Coolant Filter油過濾器臟/堵W2Air Filter空濾器臟/堵W3Separater Filter油分離芯臟/堵6KV-M250級別代碼信息含義ALARMSA1Pressure over壓力過高A2Fan moter over load風機電機過載A3Pressure Sen sor壓力傳感器壞A4Temperature Sen sor溫度傳感器壞A5Check In terlock檢查連鎖A6H-starter feadback高壓?jiǎn)?dòng)器故障A7H-Voltage Box ready?高壓?jiǎn)?dòng)器準備完畢？A8Temperature over排氣溫度過高A9Beari ng

5、 temp over軸承回油溫度咼A10k1-Co ntacter faultK1繼電器故障A11H-Motor over load主電機過載:A12H-Motor over hot主電機軸承過熱A13Remote stop fault遠控-停機故障A14Remote start fault遠控-啟動故障A15Fan con tactor fault風機接觸器壞A16Local -Sotp fault本機停機按鈕故障A17Local-start fault本機啟動按鈕故障A18Pressure Low氣壓過底WARNINGW1Coolant Filter油過濾器臟/堵W2Air Filter空

6、濾器臟/堵W3Separater Filter油分離芯臟/堵SSR -SE In tellisys控制面板級別序號信息含義ALARMS1low sump pressure低分離前壓力2high air pressure排氣壓力高3high airend discharge temperature主機排氣溫度咼4starter fult啟動器故障5main motor overload主電機過載6fan motor overload風機電機過載7temperature senor fault溫度傳感器故障8remote stop failure遠程停機故障9remote start failur

7、e遠程啟動故障10check motor rotati on檢查電機轉向11calibration failure校正錯誤12no con trol power無控制電源13pressure senor failure壓力傳感器故障14emerge ncy stop緊急停機15scroll for alarm搜索故障WARNING1high airend discharge temperature主機排氣溫度咼2cha nge separator更換油分離芯SSR - SG In tellisys控制面板級別序號信息含義ALARMS1check inlet con trol檢查進氣控制2che

8、ck inlet con trol syetem 1(2)檢查進氣控制系統3check motor rotati on檢查電機轉向4con trol power loss失去控制電源5emerge ncy stop緊急停機6fan motoe overload風扇電機過載7high airend discharge temperature排氣溫度咼8low sump pressure筒體壓力低9low uni oaded sump pressure卸載筒體壓力低10main motor overload主電機過載11check set point檢查設定值12remote start fail

9、ure遠程啟動故障13remote stop failure遠程停機故障14sen sor failure 1AVP(or 3APT,4APT,2CCT,2ATT)傳感器故障15starter fault 1sl(2sl)啟動器故障16stepper limit switch限位開關同時激活17inv alid calibrati on較零無效18low coola nt pressure油壓低WARNING1change coolant filter更換油過濾芯2change inlet filter更換空氣過濾器3cha nge separator eleme nt更換油分離芯4high

10、discharge pressure排氣壓力高5high airend discharge temperature主機排氣溫度咼6sen sor failure 4ATT傳感器4att故障7auxiliary1(2)輔助觸點1or2閉合8high sump/li ne dif分離前后壓差大9com muni cati on fail通訊失敗10service required需要服務11senor failure 6ATT傳感器6ATT故障ISC控制面板級別序號信息含義ALARM1#1 COMM FAILURE1號壓縮機通訊故障2SENSOR FAILURE傳感器故障STAUS1#1 LOCA

11、L1號壓縮機當?shù)乜刂?#1 RUNNING LOCAL1號壓縮機當?shù)乜刂魄壹虞d3#1 STOPPED1號機順序控制自啟動模式下停機4#1 RUNNING1號壓縮機順序控制并運行5#1 WARNNG1號壓縮機有警告信息6# 1 ALARM1號壓縮機有報警而停機SIERRA -SG In tellisys控制面板級別序號信息含義ALARMS1INLET RESTRICTION進氣受阻2HIGH I/C PRESS咼中間冷卻器壓力3HIGH 2ND STG PRESS二級排氣壓力高4HIGH LINE AIR PRESS管網壓力高5LOW BRG. OIL PRESS軸承油壓低6HIGH 1ST S

12、TAGE TEMP一級排氣溫度高7HIGH I/C AIR TEMP中間冷卻器氣體溫度高8HIGH 2ND STAGE TEMP二級排氣溫度咼9HIGH BRG. OIL TEMP軸承油溫高10STARTER FAULT啟動器故障11MAIN MOTOR OVERLOAD主電機過載12FAN MOTOR OVERLOAD風扇電機過載113REMOTE STOP FAILURE遠程停機失敗14REMOTE START FAILURE遠程啟動失敗15SENSOR FAILURE傳感器故障16HIGH I/C CONDENSATE中間冷卻器冷凝水液位高（選項）17LOW WATER FLOW冷卻水流

13、量低（選項）18EMERGENCY STOP緊急停機WARNING1CHANGE INLET FILTER更換進氣過濾器2CHANGE OIL FILTER更換油過濾器3SENSOR FAILURE傳感器故障SIERRA -SE In tellisys控制面板級別序號信息含義ALARMS1Low Oil Pressure油壓低2High Air Pressure高氣體壓力3High 1st Stage Discharge Temperature一級排氣壓力高4High 2nd Stage In let Temperature二級進氣溫度咼5High 2nd Stage Discharge Temperature二級排氣溫度咼6High Beari ng Oil Temperature軸承油溫高7High Conden sate Level冷凝水液位高8Temperature Sen sor Failure (2ATT/4ATT/5OTT)溫度傳感器故障9Remote Stop Failure遠程停機失敗10Remote Start Failure遠程啟動失敗11Calibrati on Failure校