AVR定時計數器0,1,2的相位可調PWM模式徹底應用

1、/*AVR定時計數器0,1,2的相位可調PWM模式徹底應用*FileName : adjustablePWM.cAuthor : 滄海麒麟Date : 2011.05.28Version : 1.0Clock Frequency ：8 MHZDescription : 適用于ATmega16(L)AVR的3個定時計數器相位頻率PWM模式 查詢與中斷的基本應用*/#include <iom16v.h> /常用頭文件,如有需要可以查庫文件include#include <avrdef.h>#include <macros.h>#include <strin

2、g.h>#include <math.h>/#include "delay.c"/#include "LCM1602.c"#define uint unsigned int#define uchar unsigned char/*T/C0*/void Timer0PCPWM_Init(uchar temp);void Timer0PCPWM_NquiryMode(uchar temp);/T/C0查詢方式函數void Timer0PCPWM_InterruptMode(uchar temp);/T/C0中斷方式函數/*T/C2*/voi

3、d Timer2PCPWM_Init(uchar temp);void Timer2PCPWM_NquiryMode(uchar temp);/T/C2查詢方式函數void Timer2PCPWM_InterruptMode(uchar temp);/T/C2中斷方式函數/*T/C1*/void Timer1PCPWM_10_Init(uint top,uint temp);/T/C1波形產生模式:CTC4void Timer1PCPWM_11_Init(uint top,uint temp);/T/C1波形產生模式:CTC12void Timer1PCPWM_A_NquiryMode(uin

4、t temp);/T/C1比較匹配A查詢方式函數void Timer1PCPWM_B_NquiryMode(uint temp);/T/C1比較匹配B查詢方式函數void Timer1PCPWM_InterruptMode(uint temp);/T/C1中斷方式函數void main(void) /占空比為1/5 Timer0PCPWM_Init(51);/245Hz Timer2PCPWM_Init(51); Timer1PCPWM_10_Init(1249,250);/50HZ /Timer1PWM_14_Init(1249,250); while (1);/*定時計數器的函數*/*與8

5、位T/C0相關的寄存器1:T/C0計數寄存器TCNT0,輸出比較寄存器OCR0,定時計數器中斷屏蔽寄存器TIMSK 定時計數器中斷標志寄存器TIFR,T/C0控制寄存器TCCR02:每計數一次需要的時間是(1/Xtal)*N us 在此程序中Xtal=8,N定義為與分頻系數N:1,8,64,256,1024 1 : TCCR0|=0x01;/0:無時鐘，系統不工作 8 : TCCR0|=0x02; 64 : TCCR0|=0x03; 256 : TCCR0|=0x04; 1024: TCCR0|=0x05; /0x06:時鐘由T0引腳輸入，下降沿觸發 0x07:時鐘由T0引腳輸入，上升沿觸發

6、*/*/void Timer0PCPWM_Init(uchar temp)/Foc0pwm = Fclk/(510N)DDRB |= 0X08;TCNT0 = 0x00; TCCR0 = 0x40|0x20|0x03; /PWM設置|OC0觸發方式的設置|預分頻設置 OCR0 = temp;/在此程序中Xtal=8,N定義為與分頻系數N:1,8,64,256,1024/1 : TCCR0|=0x01;/0:無時鐘，系統不工作/8 : TCCR0|=0x02;/64 : TCCR0|=0x03;/256 : TCCR0|=0x04;/1024: TCCR0|=0x05; /*/void Time

7、r0PCPWM_NquiryMode(uchar temp)/T/C0查詢方式函數while(!(TIFR&0x02); TIFR=0x02;OCR0 = temp;/Focnpwm = Fclk/N(1+TOP)/*/void Timer0PCPWM_InterruptMode(uchar temp)/T/C0中斷方式函數 CLI(); /disable all interrupts TCCR0 = 0x00; /stop TCNT0 = 0x00; TCCR0 = 0x40|0x20|0x03; /PWM設置|OC0觸發方式的設置|預分頻設置 OCR0 = temp; MCUCR

8、= 0x00; GICR = 0x00; TIMSK = 0x02; /timer interrupt sources SEI(); /re-enable interrupts /SREG|=BIT(7);/開啟總中斷/*/#pragma interrupt_handler timer0_comp_isr:iv_TIM0_COMP /20void timer0_comp_isr(void) /compare occured TCNT0=OCR0/*/*與8位T/C2相關的寄存器1:T/C2計數寄存器TCNT0,輸出比較寄存器OCR2,定時計數器中斷屏蔽寄存器TIMSK 定時計數器中斷標志寄存器

9、TIFR,T/C2控制寄存器TCCR22:每計數一次需要的時間是(1/Xtal)*N us 在此程序中Xtal=8,N定義為與分頻系數N:1,8,64,256,1024 1 : TCCR2|=0x01;/0:無時鐘，系統不工作 8 : TCCR2|=0x02; 32 : TCCR2|=0x03; 64 : TCCR2|=0x04; 128 : TCCR2|=0x05; 256 : TCCR2|=0x06; 1024: TCCR2|=0x07;*/*/void Timer2PCPWM_Init(uchar temp)/Foc0pwm = Fclk/(510N)DDRD |= 0X80;TCNT2

10、 = 0x00; TCCR2 = 0x40|0x20|0x04; /PWM設置|OC2觸發方式的設置|預分頻設置OCR2 = temp; /Focnpwm = Fclk/N(1+TOP)/*/void Timer2PCPWM_NquiryMode(uchar temp)/T/C2查詢方式函數while(!(TIFR&0x80); TIFR=0x80;OCR2 = temp;/*/void Timer2PCPWM_InterruptMode(uchar temp)/T/C2中斷方式函數 CLI(); /disable all interrupts TCCR2 = 0x00; /stop

11、TCNT2 = 0x00; /set count/temp=6,N=64:2000us;計數250次 TCCR2 = 0x40|0x20|0x04; /PWM設置|OC2觸發方式的設置|預分頻設置 OCR2 = temp; MCUCR = 0x00; GICR = 0x00; TIMSK = 0x80; /timer interrupt sources SEI(); /re-enable interrupts /SREG|=BIT(7);/開啟總中斷#pragma interrupt_handler timer2_comp_isr:iv_TIM2_COMP /4void timer2_comp

12、_isr(void) /compare occured TCNT2=OCR2/*/*與16位T/C1相關的寄存器1:T/C1計數寄存器TCNT1H和TCNT1L,輸出比較寄存器OCR1A(H/L)和OCR1B(H/L), 定時計數器中斷屏蔽寄存器TIMSK,定時計數器中斷標志寄存器TIFR, T/C1控制寄存器TCCR1A和TCCR1B2:每計數一次需要的時間是(1/Xtal)*N us 在此程序中Xtal=8,N定義為與分頻系數N:1,8,64,256,1024 /1 : TCCR1B=0x01;/0:無時鐘，系統不工作 /8 : TCCR1B=0x02; /64 : TCCR1B=0x03

13、; /256 : TCCR1B=0x04; /1024: TCCR1B=0x05; /0x06:時鐘由T1引腳輸入，下降沿驅動 0x07:時鐘由T1引腳輸入，上升沿驅動 */*/void Timer1PCPWM_10_Init(uint top,uint temp)DDRD |= 0x30;TCNT1H = 0x00;TCNT1L = 0x00;TCCR1A = 0x80|0x20|(1 << WGM11)|(0 << WGM10); /OC1A&OC1B的觸發方式設置|PWM設置 TCCR1B = (1 << WGM13)|(0 <<

14、WGM12)|0x03;/PWM設置|預分頻設置ICR1 = top; /Focnpwm = Fclk/(2N*TOP)OCR1A = temp;OCR1B = temp;/*/void Timer1PCPWM_11_Init(uint top,uint temp)DDRD |= 0x30;TCNT1H = 0x00;TCNT1L = 0x00;TCCR1A = 0x80|0x20|(1 << WGM11)|(1 << WGM10); /OC1A&OC1B的觸發方式設置 TCCR1B = (1 << WGM13)|(0 << WGM12)

15、|0x03;/PWM設置|預分頻設置OCR1A = top; /Focnpwm = Fclk/(2N*TOP)OCR1B = temp;/說明還有8 9 10位相位修正PWM可用/*/void Timer1PCPWM_A_NquiryMode(uint temp)/T/C1比較匹配A查詢方式函數while(!(TIFR&0x10); TIFR = 0x10;OCR1A = temp; /Focnpwm = Fclk/(2N*TOP)/*/void Timer1PCPWM_B_NquiryMode(uint temp)/T/C1比較匹配B查詢方式函數while(!(TIFR&0x

16、08); TIFR = 0x08;OCR1B = temp; /Focnpwm = Fclk/(2N*TOP)/*中斷方式函數視具體情況而定*/void Timer1PCPWM_InterruptMode(uint temp)/T/C1中斷方式函數 CLI(); /disable all interrupts DDRD |= 0x30; TCNT1H = 0x00; TCNT1L = 0x00; TCCR1A = 0xA0|(1 << WGM11)|(1 << WGM10); /OC1A&OC1B的觸發方式設置|PWM設置 TCCR1B = (1 << WGM13)|(1 << WGM12)|0x03;/PWM設置|預分頻設置 OCR1A = temp; OCR1B = temp; /Focnpwm = Fclk/(2N*TOP) MCUCR = 0x00; GICR = 0x00; TIMSK = 0x18; /timer interrupt sources SEI(); /re-enable in