紅外遙控器接收程序

1、/STC89C52RC/11.0592MHZ#include #include #define uchar unsigned char#define uint unsigned int#define TH0_VALUE 0xc5#define TL0_VALUE 0xc5 / 定時器計數值 #define ANT P24 /紅外IO口，可任意一個IO/系統變量定義區=volatile unsigned char irr_b=0,s_s=0;/irr_b接收狀態指示，s_s顯示許可volatile signed long da=0; /32位數據碼volatile unsigned char w

2、b=0, a=0; /wb為接收到的位數，a為接收到信號高低電平判斷依據volatile unsigned int js=0; /定時器計數volatile unsigned char a1=1,a2=1; /上升沿處理變量void timer_init(voidET0=0; TMOD=0x02; TCON=0x10; TL0=TL0_VALUE;TH0=TH0_VALUE;ET0=1;void timer_start(TR0=1;EA=1;void timer0_interrupt(void interrupt 1 /大約63us中斷一次js+;/判斷下降a2=ANT;if (a1>a

3、2 if(irr_b=0 /第一個中斷irr_b=1; /狀態為：開始接收js=0;else if(irr_b=1 /第二個以后的中斷a=js; /讀取定時器的值if(170 判斷是引導，還是數據 10.7ms-15.7ms 引導碼長 13.5ms wb=0; /數據計數清零 da=0; /數據清零js=0; /定時器清零 else /數據 if(8 低電平長 1.125ms wb+;js=0; da=(da<<1 ;elseif(25 高電平長 2.25ms wb+;js=0; da=(da<<1 +1 ;if(wb>=32 /數據長度夠32位irr_b=0;

4、/狀態為停止接收wb=0; /數據計數清零s_s=1; /打開顯示許可a1=a2; /a為兩個下降沿之間的時間void program(voiduchar ds=0,d1;while(1ds=js;if(ds>250 /定時器超時，接收復位js=0;irr_b=0;da=0;wb=0; s_s=0;if(s_s=1 /顯示開關打開，開始顯示TR0=0; /關閉全局中斷/顯示設備碼d1=da>>8;d1=da; /把long型的da強制轉換為char型的d1switch(d1case 0xff:P2=0xff;uart_tx(255;break; /停止，燈全滅case 0x9

5、f:P2=0xfe;uart_tx(191;break; /正轉，對應的燈亮case 0x5f:P2=0xfd;uart_tx(239;break; /反轉，對應的燈亮case 0xaf:P2=0xfb;uart_tx(251;break; /加速，對應的燈亮case 0x6f:P2=0xf7;uart_tx(254;break; /減速，對應的燈亮default:break; s_s=0; /關閉顯示開關TR0=1; /開全局中斷void delay_ms(unsigned int iunsigned int j;while(i-for(j=0;j<75;j+;void uart_in

6、it(TMOD|=0X20; /只把M1置為1，其余位不變，默認為0TH1=0XFD;TL1=0XFD;SCON=0X50; / 設定串行口工作方式PCON&=0XEF; / 波特率不倍增，只把倍增位置0，其他位保持不變，默認為0TR1=1;void uart_tx(unsigned char txdSBUF=txd;while(!TI;TI=0;void uart_cn(unsigned char *cn,unsigned char cn_nubunsigned char i;for(i=0;i<(cn_nub;i+uart_tx(cni; /發送數據i_nop_(;_nop_(;_nop_(;_nop_(;_nop_(; /無實際意義，后移cpu指針，使指令按字對