a hand book for the mechanical designer ventilation, duct, fan

1、a handbook for the mechanical designer second edition copyright 1999 this handy engineering information guide is a token of loren cook companys appreciation to the many ne mechanical designers in our industry. springeld, mo table of contents fan basics fan types . . . . . . . . . . . . . . . . . . .

2、 . . . . . . . . . . . . . . . . . . . . 1 fan selection criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 fan laws. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 fan performance tables and curves . . . . . . . . . . . . . . . . . . 2 fan testing

3、- laboratory, field . . . . . . . . . . . . . . . . . . . . . . . 2 air density factors for altitude and temperature . . . . . . . . . 3 use of air density factors - an example . . . . . . . . . . . . . . . 3 classications for spark resistant construction . . . . . . . .4-5 impeller designs - centri

4、fugal. . . . . . . . . . . . . . . . . . . . . . .5-6 impeller designs - axial . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 terminology for centrifugal fan components. . . . . . . . . . . . 8 drive arrangements for centrifugal fans . . . . . . . . . . . . .9-10 rotation & discharge

5、designations for centrifugal fans 11-12 motor positions for belt or chain drive centrifugal fans . . 13 fan installation guidelines . . . . . . . . . . . . . . . . . . . . . . . . . 14 fan troubleshooting guide. . . . . . . . . . . . . . . . . . . . . . . . . 15 motor and drive basics denitions and

6、formulas . . . . . . . . . . . . . . . . . . . . . . . . . . 16 types of alternating current motors . . . . . . . . . . . . . . . .17-18 motor insulation classes. . . . . . . . . . . . . . . . . . . . . . . . . . . 18 motor service factors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

7、locked rotor kva/hp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 motor efciency and epact. . . . . . . . . . . . . . . . . . . . . . . . . 20 full load current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-22 general effect of voltage and frequency . . . . . . . . . .

8、. . . . 23 allowable ampacities of not more than three insulated conductors . . . . . . . . . . . . . . . . . . . . . . . . .24-25 belt drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 estimated belt drive loss. . . . . . . . . . . . . . . . . . . . . . . . . . 27

9、 bearing life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 system design guidelines general ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 process ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 kitchen ventila

10、tion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 rules of thumb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31-32 noise criteria . . . . . . . . . . . . . . . . . . . . .

11、 . . . . . . . . . . . . . . 32 table of contents system design guidelines (cont.) sound power and sound power level. . . . . . . . . . . . . . . . . 32 sound pressure and sound pressure level . . . . . . . . . . . . 33 room sones dba correlation . . . . . . . . . . . . . . . . . . . . . 33 noise cr

12、iteria curves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 design criteria for room loudness. . . . . . . . . . . . . . . . .35-36 vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 vibration severity . . . . . . . . . . . . . . . . . . . . .

13、 . . . . . . . . .38-39 general ventilation design air quality method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 air change method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 suggested air changes. . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 v

14、entilation rates for acceptable indoor air quality . . . . . . . 42 heat gain from occupants of conditioned spaces . . . . . . 43 heat gain from typical electric motors. . . . . . . . . . . . . . . . 44 rate of heat gain commercial cooking appliances in air-conditioned areas. . . . . . . . . . . . .

15、 . . . . . . . . . . . . . . . 45 rate of heat gain from miscellaneous appliances . . . . . . 46 filter comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 relative size chart of common air contaminants . . . . . . . 47 optimum relative humidity ranges for health . . . . .

16、. . . . . 48 duct design backdraft or relief dampers . . . . . . . . . . . . . . . . . . . . . . . . 49 screen pressure drop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 duct resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 rectangular equivalent of rou

17、nd ducts . . . . . . . . . . . . . . . 52 typical design velocities for hvac components. . . . . . . . . 53 velocity and velocity pressure relationships . . . . . . . . . . . 54 u.s. sheet metal gauges . . . . . . . . . . . . . . . . . . . . . . . . . . 55 recommended metal gauges for ducts . . . .

18、. . . . . . . . . . . 56 wind driven rain louvers. . . . . . . . . . . . . . . . . . . . . . . . . . 56 heating & refrigeration moisture and air relationships . . . . . . . . . . . . . . . . . . . . . . 57 properties of saturated steam . . . . . . . . . . . . . . . . . . . . . . 58 cooling load

19、check figures . . . . . . . . . . . . . . . . . . . . . .59-60 heat loss estimates . . . . . . . . . . . . . . . . . . . . . . . . . . . .61-62 fuel comparisons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 fuel gas characteristics. . . . . . . . . . . . . . . . . . . . . . . .

20、. . . 62 table of contents heating & refrigeration (cont.) estimated seasonal efciencies of heating systems. . . . 63 annual fuel use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63-64 pump construction types . . . . . . . . . . . . . . . . . . . . . . . . . 64 pump impeller types.

21、 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 pump bodies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 pump mounting methods . . . . . . . . . . . . . . . . . . . . . . . . . 65 afnity laws for pumps. . . . . . . . . . . . . . . . . . . . . . . . . . . 66 pum

22、ping system troubleshooting guide . . . . . . . . . . . 67-68 pump terms, abbreviations, and conversion factors. . . . 69 common pump formulas. . . . . . . . . . . . . . . . . . . . . . . . . 70 water flow and piping . . . . . . . . . . . . . . . . . . . . . . . . .70-71 friction loss for water flow

23、 . . . . . . . . . . . . . . . . . . . . .71-72 equivalent length of pipe for valves and fittings . . . . . . . 73 standard pipe dimensions . . . . . . . . . . . . . . . . . . . . . . . . 74 copper tube dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 74 typical heat transfer coefcients.

24、 . . . . . . . . . . . . . . . . . . 75 fouling factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 cooling tower ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 evaporate condenser ratings . . . . . . . . . . . . . . . . . . . . . 78 compressor capacity vs

25、. refrigerant temperature at 100°f condensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 refrigerant line capacities for 134a. . . . . . . . . . . . . . . . . 79 refrigerant line capacities for r-22. . . . . . . . . . . . . . . . . 79 refrigerant line capacities for r-502. . .

26、 . . . . . . . . . . . . . 80 refrigerant line capacities for r-717. . . . . . . . . . . . . . . . 80 formulas & conversion factors miscellaneous formulas . . . . . . . . . . . . . . . . . . . . . . . .81-84 area and circumference of circles. . . . . . . . . . . . . . . .84-87 circle formula. .

27、. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 common fractions of an inch. . . . . . . . . . . . . . . . . . . .87-88 conversion factors . . . . . . . . . . . . . . . . . . . . . . . . . . . .88-94 psychometric chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

28、index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96-103 fan basics fan types axial fan - an axial fan discharges air parallel to the axis of the impeller rotation. as a general rule, axial fans are preferred for high volume, low pressure, and non-ducted systems.

29、 axial fan types propeller, tube axial and vane axial. centrifugal fan - centrifugal fans discharge air perpendicular to the axis of the impeller rotation. as a general rule, centrifugal fans are preferred for higher pressure ducted systems. centrifugal fan types backward inclined, airfoil, forward

30、curved, and radial tip. fan selection criteria before selecting a fan, the following information is needed. air volume required - cfm system resistance - sp air density (altitude and temperature) type of service environment type materials/vapors to be exhausted operation temperature space limitation

31、s fan type drive type (direct or belt) noise criteria number of fans discharge rotation motor position expected fan life in years 1 fan basics fan laws the simplied form of the most commonly used fan laws include. cfm varies directly with rpm cfm1/cfm2 = rpm1/rpm2 sp varies with the square of the rp

32、m sp1/sp2 = (rpm1/rpm2)2 hp varies with the cube of the rpm hp1/hp2 = (rpm1/rpm2)3 fan performance tables and curves performance tables provide a simple method of fan selection. however, it is critical to evaluate fan performance curves in the fan selection process as the margin for error is very sl

33、im when selecting a fan near the limits of tabular data. the performance curve also is a valuable tool when evaluating fan performance in the eld. fan performance tables and curves are based on standard air density of 0.075 lb/ft3. when altitude and temperature differ signicantly from standard condi

34、tions (sea level and 70° f) performance modication factors must be taken into account to ensure proper performance. for further information refer to use of air density factors an example, page 3. fan testing - laboratory, field fans are tested and performance certied under ideal laboratory cond

35、itions. when fan performance is measured in eld conditions, the difference between the ideal laboratory condition and the actual eld installation must be considered. consideration must also be given to fan inlet and discharge connections as they will dramatically affect fan performance in the eld. i

36、f possible, readings must be taken in straight runs of ductwork in order to ensure validity. if this cannot be accomplished, motor amperage and fan rpm should be used along with performance curves to estimate fan performance. for further information refer to fan installation guidelines, page 14. 2 f

37、an basics air density factors for altitude and temperature altitude temperature (ft.) 70 100 200 300 400 500 600 700 0 1.000 .946 .803 .697 .616 .552 .500 .457 1000 .964 .912 .774 .672 .594 .532 .482 .441 2000 .930 .880 .747 .648 .573 .513 .465 .425 3000 .896 .848 .720 .624 .552 .495 .448 .410 4000

38、.864 .818 .694 .604 .532 .477 .432 .395 5000 .832 .787 .668 .580 .513 .459 .416 .380 6000 .801 .758 .643 .558 .493 .442 .400 .366 7000 .772 .730 .620 .538 .476 .426 .386 .353 8000 .743 .703 .596 .518 .458 .410 .372 .340 9000 .714 .676 .573 .498 .440 .394 .352 .326 10000 .688 .651 .552 .480 .424 .380

39、 .344 .315 15000 .564 .534 .453 .393 .347 .311 .282 .258 20000 .460 .435 .369 .321 .283 .254 .230 .210 use of air density factors - an example a fan is selected to deliver 7500 cfm at 1-1/2 inch sp at an altitude of 6000 feet above sea level and an operating temperature of 200° f. from the tabl

40、e above, air density factors for altitude and temperature, the air density correction factor is determined to be .643 by using the fans operating altitude and temperature. divide the design sp by the air density correction factor. 1.5” sp/.643 = 2.33” sp referring to the fans performance rating tabl

41、e, it is determined that the fan must operate at 976 rpm to develop the desired 7500 cfm at 6000 foot above sea level and at an operating temperature of 200° f. the bhp (brake horsepower) is determined from the fans performance table to be 3.53. this is corrected to conditions at altitude by mu

42、ltiplying the bhp by the air density correction factor. 3.53 bhp x .643 = 2.27 bhp the nal operating conditions are determined to be 7500 cfm, 1-1/2” sp, 976 rpm, and 2.27 bhp. 3 fan basics classifications for spark resistant constructionfan applications may involve the handling of potentially explo

43、sive or ammable particles, fumes or vapors. such applications require careful consideration of all system components to insure the safe handling of such gas streams. this amca standard deals only with the fan unit installed in that system. the standard contains guidelines which are to be used by bot

44、h the manufacturer and user as a means of establishing general methods of construction. the exact method of construction and choice of alloys is the responsibility of the manufacturer; however, the customer must accept both the type and design with full recognition of the potential hazard and the de

45、gree of protection required. construction type a. all parts of the fan in contact with the air or gas being handled shall be made of nonferrous material. steps must also be taken to assure that the impeller, bearings, and shaft are adequately attached and/or restrained to prevent a lateral or axial

46、shift in these components. b. the fan shall have a nonferrous impeller and nonferrous ring about the opening through which the shaft passes. ferrous hubs, shafts, and hardware are allowed provided construction is such that a shift of impeller or shaft will not permit two ferrous parts of the fan to

47、rub or strike. steps must also be taken to assure the impeller, bearings, and shaft are adequately attached and/or restrained to prevent a lateral or axial shift in these components. c. the fan shall be so constructed that a shift of the impeller or shaft will not permit two ferrous parts of the fan

48、 to rub or strike. notes 1. no bearings, drive components or electrical devices shall be placed in the air or gas stream unless they are constructed or enclosed in such a manner that failure of that component cannot ignite the surrounding gas stream. 2. the user shall electrically ground all fan par

49、ts. 3. for this standard, nonferrous material shall be a material with less than 5% iron or any other material with demonstrated ability to be spark resistant. adapted from amca standard 99-401-86 4 fan basics classications for spark resistant construction (cont.) 4.the use of aluminum or aluminum a

50、lloys in the presence of steel which has been allowed to rust requires special consideration. research by the u.s. bureau of mines and others has shown that aluminum impellers rubbing on rusty steel may cause high intensity sparking. the use of the above standard in no way implies a guarantee of saf

51、ety for any level of spark resistance. “spark resistant construction also does not protect against ignition of explosive gases caused by catastrophic failure or from any airstream material that may be present in a system.” standard applications centrifugal fans axial and propeller fans power roof ve

52、ntilators this standard applies to ferrous and nonferrous metals. the potential questions which may be associated with fans constructed of frp, pvc, or any other plastic compound were not addressed. impeller designs - centrifugal airfoil - has the highest efciency of all of the centrifugal impeller

53、designs with 9 to 16 blades of airfoil contour curved away from the direction of rotation. air leaves the impeller at a velocity less than its tip speed. relatively deep blades provide for efcient expansion with the blade passages. for the given duty, the airfoil impeller design will provide for the

54、 highest speed of the centrifugal fan designs. applications - primary applications include general heating systems, and ventilating and air conditioning systems. used in larger sizes for clean air industrial applications providing signicant power savings. 5 fan basics impeller designs - centrifugal

55、(cont.) backward inclined, backward curved - efciency is slightly less than that of the airfoil design. backward inclined or backward curved blades are single thickness with 9 to 16 blades curved or inclined away from the direction of rotation. air leaves the impeller at a velocity less than its tip

56、 speed. relatively deep blades provide efcient expansion with the blade passages. applications -primary applications include general heating systems, and ventilating and air conditioning systems. also used in some industrial applications where the airfoil blade is not acceptable because of a corrosi

57、ve and/or erosive environment. radial - simplest of all centrifugal impellers and least efcient. has high mechanical strength and the impeller is easily repaired. for a given point of rating, this impeller requires medium speed. classication includes radial blades and modied radial blades), usually

58、with 6 to 10 blades. applications -used primarily for material handling applications in industrial plants. impeller can be of rugged construction and is simple to repair in the eld. impeller is sometimes coated with special material. this design also is used for high pressure industrial requirements and is not commonly fou